• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.496-498
• /
• 2005

We reported that high dielectric hafnium oxide nano-film deposited by thermal atomic layer deposition on the poly-silicon film (poly-Si). The poly -Si film was produced by plasma enhanced chemical vapor deposition and excimer laser annealing. We used the hafniu m chloride ($HfCl_4$) and water as the precursors and analyzed the hafnium oxide film by transmission electron microscope and secondary ion mass spectrometer. Hafnium oxide produced by the ALD method showed very good coverage on the rough surface of poly-Si film. While deposited with 200 cycles, these hafnium oxide films revealed a relatively smooth surface and good uniformity, but the cumulative roughness produced by the incomplete reaction was apparent when the amount of deposition cycle increased to 600 cycles.

• Journal of the Korea Society of Computer and Information
• /
• v.22 no.7
• /
• pp.39-45
• /
• 2017

In this paper, we propose three compensation methods to solve problems in high-resolution airborne infrared camera and to improve long-range target information acquisition performance. First, image motion and temporal noise reduction technique which is caused by atmospheric turbulence. Second, thermal blurring image correction technique by imperfect performance of NUC(Non Uniformity Correction) or raising the internal temperature of the camera. Finally, DRC(Dynamic Range Compression) and flicker removing technique of 14bits HDR(High Dynamic Range) infrared image. Through this study, we designed techniques to improve the acquisition performance of long-range target information of high-resolution airborne infrared camera, and compared and analyzed the performance improvement result with implemented images.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.338-338
• /
• 2011

최근 FPD (Flat Pannel Display) 시장이 커짐에 따라 고효율, 저비용 제작 공정이 화두로 떠오르고 있다. ELA (Excimer Laser Annenling)을 이용한 LTPS (Low Temperature Poly Silicon) 공정은 mobility와 전류 점멸비 등에서 장점을 가지지만, 고비용, 대면적과 short-range에서 uniformity가 어렵다는 단점이 있다. 이를 극복하기 위한 방법으로 dLTA (diode Laser Thermal Annealing) 공정에 대한 연구가 진행되고 있다. 본 연구에서는 Flexible Display을 만들기 위한 방법으로 dLTA 공정을 진행하였다. 이 방법은 PI (Poly imide) 기판 위에 a-Si을 ICP CVD로 증착시킨 후, Diode Laser (980 nm)를 이용한 annealing을 통하여 a-Si이 poly-Si으로 결정화가 되는 것을 확인하였고, 에너지 조사량에 따른 grain boundary와 grain size을 통하여 비교 분석하였다. 실험 결과 ELA 공정을 이용한 것과 버금가는 실험 결과를 얻을 수 있었다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.2
• /
• pp.244-249
• /
• 2000

Thermal gradient chemical vapor infiltration (TG-CVI) process, which is one of the CVI techniques to densify a porous fiber preform, requires for a heater to have uniform surface temperature distribution. Thus, it is essential to design the shape of the heater and to predict the temperature distribution when the heater has a profile which is not a simple cylinder. In this study, an analytical method has been used to design the inner profile of a conical heater showing uniform temperature distribution, if its outer shape is specified. Temperature distribution on the heater surface has been calculated with the finite difference method and compared with the experimental results. When a heater had a combined profile with a large cone and a small cylinder, temperature was higher in the cylindrical part. To reduce the temperature difference between these areas, a hole-machining method has been proposed including other possible ones. A shape design and optimization program has been made to improve the temperature uniformity of the TG-CVI heater better than that designed with the analytical method.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.5
• /
• pp.278-285
• /
• 2006

A micro hotplate for micro gas sensor was fabricated by MEMS technology. In order to heat up the gas sensing material to a target temperature, a micro hotplate was built on the gas sensor. The sensing material was deposited on the heater and electrodes, and did not contact with the silicon base to minimize the heat loss to the silicon base. The electric power to heat up the gas sensor was measured. The temperature distribution of micro gas sensor was analyzed by a CFD program. The predicted electric power to heat up th sensing material showed a good agreement with the measured data. The design of micro gas sensor could be modified to increase the temperature uniformity and to decrease the electric power consumption by optimizing the layout of micro hotplate and electrodes.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2886-2891
• /
• 2008

The purpose of this study is to develop a highly-efficient and compact steam reformer for PEMFC changing the burner types. For the purpose some of the Can type flat burners were adopted and the results were compared with 'O' company's typical cylinderical flat burner. We used commercial STAR-CD tools for numerical calculation. We found the optimum Can type STR burner and this type of burner was highly efficient comparing with typical burner.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.103-106
• /
• 2006

The Plate reformer consisting of combustion chamber and reforming chamber for 25 kW MCFC stack has been operated and computational fluid dynamics was applied to estimate reactions and thermal fluid behavior in the reformer. The methane air 2-stage reaction was assumed in the combustion chamber, and three step steam reforming reactions were included in the calculation. Flow uniformity, reaction rate and species distribution, and temperature distribution were analyzed. In particular, temperature distribution was compared with the measurements to show good agreement in the combustion chamber, however, inappropriate agreement in the reformer chamber

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.12
• /
• pp.54-64
• /
• 2021

Electric vehicles use lithium-ion battery packs as the power supply, where the batteries are connected in series or parallel. The temperature control of each battery is essential to ensure a consistent overall temperature. This study focused on reducing ohmic heating caused by batteries to realize a uniform battery temperature. The battery spacing was optimized to improve air cooling, and the tilt angle between the batteries was varied to optimize the internal structure of the batterypack. Simulations were performed to evaluate the effects of these parameters, and the results showed that the optimal scheme effectively achieved a uniform battery temperature under a constant power discharge. These findings can contribute to future research on cooling methods for battery packs.

• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.42-46
• /
• 2012

The effect of the parameters for few-layered graphene growth by thermal CVD on nickel substrate was investigated. Graphene can be synthesized by using different strategies. Chemical vapor deposition (CVD) has known as one of the most attractive methods to produce graphene due to its good film uniformity, compatibility and large scale production. The control of parameters such as temperature, growth time and pressure in CVD process has been widely recognized as the most important process in graphene growth. Different carbon precursors, methane and acetylene, were introduced in the quartz tube with a variety of growth conditions. Raman spectroscopy was used to confirm the presence of a few- or multi-layered graphene.

• Journal of Information Display
• /
• v.2 no.3
• /
• pp.44-47
• /
• 2001

The extracted field emission current can be used to controllably heat microfabricated cold field emission cathode tips. The heating can be sufficient to smooth and recrystallize the tip surface by surface self-diffusion, and at least partially clean the surface of contaminants by thermal desorption. Self-heating not only allows for the achievement and maintenance of stable emission characteristics, but can be used to make the current-voltage characteristics of microfabricated field emitter tips nearly identical to one another. The resulting improvement in emission uniformity will allow for more reliable array operation at increased electron emission current densities.