• Nuclear Engineering and Technology
• /
• v.55 no.12
• /
• pp.4518-4526
• /
• 2023

NECP-SARAX is a neutronics analysis code system for advanced reactor developed by Nuclear Engineering Computational Physics Laboratory of Xi'an Jiaotong University. In past few years, improvements have been implemented in TULIP code which is the cross-section generation module of NECP-SARAX, including the treatment of resonance interface, considering the self-shielding effect in non-resonance energy range, hyperfine group method and nuclear library with thermal scattering law. Previous studies show that NECP-SARAX has high performance in both fast and thermal spectrum system analysis. The accuracy of TULIP code in fast and thermal spectrum system analysis is demonstrated preliminarily. However, a systematic verification and validation is still necessary. In order to validate the applicability of TULIP code for full energy range, 147 fast spectrum critical experiment benchmarks and 170 thermal spectrum critical experiment benchmarks were selected from ICSBEP and used for analysis. The keff bias between TULIP code and reference value is less than 300 pcm for all fast spectrum benchmarks. And that bias keeps within 200 pcm for thermal spectrum benchmarks with neutron-moderating materials such as polyethylene, beryllium oxide, etc. The numerical results indicate that TULIP code has good performance for the analysis of fast and thermal spectrum system.

• 한국전기화학회:학술대회논문집
• /
• 2001.11a
• /
• pp.145-161
• /
• 2001

Novel characterization of thermal properties of a battery has been introduced by defining its frequency-dependent thermal impedance function. Thermal impedance function can be approximated as a thermal impedance spectrum by analyzing experimental temperature transient which is related to the thermal impedance function through Laplace transformation. In order to obtain temperature transient, a process has been devised to generate external heat pulse with heating wire and to measure the response of battery. This process is used to study several commercial Li-ion batteries of cylindrical type. The thermal impedance measurements have been performed using potentionstat/galvanostate controlled digital signal processor, which is more commonly available than flow-meter usually applied for thermal property measurements. Thermal impedance spectra obtained for batteries produced by different manufactures are found to differ considerably. Comparison of spectra at different states of charge indicates independence of thermal impedance on charging state of battery. It is shown that thermal impedance spectrum can be used to obtain simultaneously thermal capacity and thermal conductivity of battery by non-linear complex least-square fit of the spectrum to thermal impedance model. Obtained data is used to simulate a response of the battery to internal heating during discharge. It is found that temperature inside the battery is by one-third larger that on its surface. This observation has to be considered to prevent damage by overheating.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.14-14
• /
• 2011

Graphene is known to possess excellent thermal properties, including high thermal conductivity, that make it a prime candidate material for heat management in ultra large scale integrated circuits. For device applications, the key parameters are the thermal expansion coefficient and the thermal conductivity. There has been no reliable experimental determination on the thermal expansion coefficient of graphene whereas the estimates of the thermal conductivity vary widely. In this work, we estimate the thermal expansion coefficient of graphene on silicon dioxide by measuring the temperature dependence of the Raman spectrum. The shift of the Raman peaks due to heating or cooling results from both the intrinsic temperature dependence of the Raman spectrum of graphene and the strain on the graphene film due to the thermal expansion mismatch with silicon dioxide. By carefully comparing the experimental data against theoretical calculations, it is possible to determine the thermal expansion coefficient. The thermal conductivity is measured by estimating the thermal profile of a graphene film suspended over a circular hole of the substrate.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.78.4-79
• /
• 2017

Thermal inflation is an additional inflationary mechanism before the big bang nucleosynthesis, which solves the moduli problem and naturally provides a plausible dark matter candidate. Thermal inflation leaves a slight enhancement followed by huge suppression of a factor of ~50 in the curvature and matter power spectrum, which can be expressed in terms of a single characteristic scale $k_b$. Here we describe the observability of the small-scale features of thermal inflation from various observations, such as CMB distortion, satellite galaxy abundance in the Milky-Way-sized galaxies, and 21-cm power spectrum before the epoch of reionization.

• Journal of the Korean Magnetics Society
• /
• v.21 no.1
• /
• pp.5-9
• /
• 2011

M$\ddot{o}$ssbauer and Raman spectrum studies have been carried out on the 2b-site Fe ion in the Ba-ferrite (M-type). The thermal dynamics of Fe ion was analyzed by M$\ddot{o}$ssbauer spectra at different angles between the $\gamma$-ray direction and c-axis. The vibration on the 2b-site was more active compare to other direction and had very strong intensity in the Raman spectrum.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.37-38
• /
• 2017

In Infrared rays, which are 50% of sunlight, act as heat rays to heat buildings. Solar heat paint is widely used to protect buildings from sunlight. Solar heat coatings are used to block buildings form sunlight. Solar heat paints are classified as heat-reflective paints and heat-insulating paints according to the differential thermal mechanism. In this study, we study the thermal differential mechanism by analyzing the temperature change of the coated steel plate and the solar reflection spectrum on the surface. In this experiment, exposed steel plate, heat-reflective coated steel plate, heat-insulating coated steel plate, and general paint coated steel plate were used. As a result, when the infrared rays of 780nm ~ 1400nm were irradiated, the heat reflective paint had a temperature lower by 10 degrees than other paints. Analysis of the reflection spectrum of the paint shows that the heat paint is lower in heat than other paints because it has higher reflectance of light and absorbs much of the infrared rays.

• Nuclear Engineering and Technology
• /
• v.5 no.4
• /
• pp.291-309
• /
• 1973

Exposure rates due to leakage gamma-rays from operating reactors TRIGA Mark II and III were measured in a horizontal plane by means of scintillation spectrometry using a 3"$\times$3" cylindrical Nal(T1) detector associated with a 400 channel pulse height analyzer under varied conditions of reactor operation. In determining exposure rate due to the leakage gamma-rays at each point of measurement, Moriuchi's spectrum-exposure rate conversion theory was applied instead of using conventional responce matrix method which necessitates very complicated procedures to convert a spectrum into exposure rate. The results show that a basic pattern of "typical" spectrum of the reactor leakage gamma-rays is neither affected by thermal output of the reactor, nor influenced by overall attenuation in radiation intensity. It was indicated that he attenuation of the leakage gamma-rays in air in terms of exposure rate as a whole follows an exponential law, and the total exposure rate due to the leakage gamma-rays at a certain point is nearly proportional to thermal output of the reactor. The complexity in spectrum measured for a movable core reactor, TRIGA Mark III, was analyzed through spectrum resolution, and proper judgement of the leakage gamma-rays in a complex spectrum was discussed.ctrum was discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.294-297
• /
• 2013

ZnO crystals with octahedral shape were synthesized by thermal evaporation technique. $ZnF_2$ powder was used as the source material. The thermal evaporation and oxidation of $ZnF_2$ powder was carried out for 1 hr at $1,000^{\circ}C$ in air under atmospheric pressure. SEM images showed that the ZnO crystals produced by oxidizing $ZnF_2$ vapor possessed a characteristic octahedral shape. XRD spectrum revealed that the ZnO octahedron had hexagonal wurtzite structure. In the room temperature photoluminescence spectrum, a strong green emission peak at around 510 nm was observed.

• The Journal of the Acoustical Society of Korea
• /
• v.12 no.1
• /
• pp.47-54
• /
• 1993

Performance analysis is very important to transmit the high quality information and to construct the optimal system for the minimze the noise from the channel of spread spectrum system. In this paper the error rate performance is analyzed with computer simulation in noncoherent frequency hopping M-qry frequency shift keying(FH/MFSk) systems with regard to thermal noise under the partial band jamming environments. AS a result, in case the thermal noise is disregarded, bit error probability of system in jamming fraction ρ and Eb/Nj(bit energy to jamming power density) is reduced with the increase of K and in worst case 32FSK system is better than 2FSK system by 3.23dB with the variatio of Eb/Nj. In case thermal noise is considered, bit error probability of system by 3.23dB with the variation of Eb/Nj. In case thermal noise is considered, bit error probability of system are reduced with the increase of K and Eb/No(bit energy to thermal noise density). Bit error probability in connection with worst case ρ is not largely influenced form over the 14dB to K=1 and 8dB to K=5 accordingly thermal noise disregarding. These results may be useful for avoiding the common vulnerabilities when the spread spectrum system is designed.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.117-126
• /
• 2008

In this paper, a new reactor core design is proposed on the basis of a mixed core concept consisting of a thermal zone and a fast zone. The geometric structure of the fuel assembly of the thermal zone is similar to that of a conventional thermal supercritical water-cooled reactor(SCWR) core with two fuel pin rows between the moderator channels. In spite of the counter-current flow mode, the co-current flow mode is used to simplify the design of the reactor core and the fuel assembly. The water temperature at the exit of the thermal zone is much lower than the water temperature at the outlet of the pressure vessel. This lower temperature reduces the maximum cladding temperature of the thermal zone. Furthermore, due to the high velocity of the fast zone, a wider lattice can be used in the fuel assembly and the nonuniformity of the local heat transfer can be minimized. This mixed core, which combines the merits of some existing thermal SCWR cores and fast SCWR cores, is proposed for further detailed analysis.