• Journal of the Korean Applied Science and Technology
• /
• v.24 no.3
• /
• pp.278-286
• /
• 2007

As a part of enhancing the performance of wood-plastic composites (WPC), polypropylene (PP)/ nanoclay (NC)/ wood flour (WF) nanocomposites were prepared using melt blending and injection molding process to evaluate their thermal stability. Thermogravimetric analysis (TGA) was employed to investigate thermal degradation kinetics of the nanocomposites both dynamic and isothermal conditions. Dynamic scans of the TGA showed an increased thermal stability of the nanocomposites at moderate wood flour concentrations (up to 20 phr, percentage based on hundred percent resin) while it decreased with the addition of 30 phr wood flour. The activation energy $(E_a)$ of thermal degradation of nanocomposites increased when nanoclay was added and the concentration of wood flour increased. Different equations were used to evaluate isothermal degradation kinetics using the rate of thermal degradation of the composites, expressed as weight loss (%) from their isothermal TGA curves. Degradation occurred at faster rate in the initial stages of about 60 min., and then proceeded in a gradual manner. However, nanocomposites with wood flour of 30 phr heated at $300^{\circ}C$ showed a drastic difference in their degradation behavior, and reached almost a complete decomposition after 40 min. of the isothermal heating. The degree of decomposition was greater at higher temperatures, and the residual weight of isothermal degradation of nanocomposites greatly varied from about 10 to 90%, depending on isothermal temperatures. The isothermal degradation of nanocomposites also increased their thermal stability with the addition of 1 phr nanoclay and of wood flour up to 20 phr. But, the degradation of PP100/NC1/MAPP3/WF30 nanocomposites with 30 phr wood flour occurs at a faster rate compared to those of the others, indicating a decrease in their thermal stability.

• Clean Technology
• /
• v.17 no.3
• /
• pp.250-258
• /
• 2011

Thermal plasma has been presented for the decomposition of perfluorocompounds (PFCs) which are extensively used in the semiconductor manufacturing and display industry. We developed pilot-scale equipment to investigate the large scale treatment of PFCs and called it a "thermal plasma scrubber". PFCs such as $CF_4$, $C_2F_6$, $SF_6$, and $NF_3$ used in experiments were diluted with $N_2$. There were two different types of experiment setup related to the water spray direction inside the thermal plasma scrubber. The first type was that the water was sprayed directly into the gas outlet located at the exit of the reaction section. The second type was that the water was sprayed on the wall of the quenching section. More effective decomposition took place when the water was sprayed on the quenching section wall. For $C_2F_6$, $SF_6$, and $NF_3$ the maximum destruction and removal efficiency was nearly 100%, and for $CF_4$ was up to 93%.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.7
• /
• pp.2086-2092
• /
• 2013

Two new high-nitrogen energetic compounds $ZTO{\cdot}2H_2O$ and $ZTO(phen){\cdot}H_2O$ have been synthesized (where ZTO = 4,4-azo-1,2,4-triazol-5-one and phen = 1,10-phenanthroline). The crystal structure, elemental analysis and IR spectroscopy are presented. Compound 1 $ZTO{\cdot}2H_2O$ crystallizes in the orthorhombic crystal system with space group Pnna and compound 2 $ZTO(phen){\cdot}H_2O$ in the triclinic crystal system with space group P-1. In $ZTO(phen){\cdot}H_2O$, there is intermolecular hydrogen bonds between the -NH group of ZTO molecule (as donor) and N atom of phen molecule (as acceptor). Thermal decomposition process is studied by applying the differential scanning calorimetry (DSC) and thermo thermogravimetric differential analysis (TG-DTG). The DSC curve shows that there is one exothermic peak in $ZTO{\cdot}2H_2O$ and $ZTO(phen){\cdot}H_2O$, respectively. The critical temperature of thermal explosion ($T_b$) for $ZTO{\cdot}2H_2O$ and $ZTO(phen){\cdot}H_2O$ is $282.21^{\circ}C$ and $195.94^{\circ}C$, respectively.

• Journal of the Korean Institute of Gas
• /
• v.24 no.3
• /
• pp.40-46
• /
• 2020

Tertbutylperoxymaleate is the one of the organic peroxides used as a raw material of initiator formulations of artificial marble manufacturing. In this study, the thermal decomposition characteristic of TBPM was evaluated using the differential scanning calorimeter in the air and nitrogen circumstance. Regardless of the reaction atmosphere, TBPM showed the exothermic peak due to the drastic decomposition reaction below 130 ℃. The activation energy estimated by dynamic methods had a range of 203~217 kJ/mol and that estimated by model-free analysis method had a range of 118~232 kJ/mol with a thermal conversion. And the ADT₂₄, the temperature that lead to the maximum heating rate within 24 hours, was evaluated as (80~95) ℃ using the estimated activation energy.

• Journal of the Korean Magnetics Society
• /
• v.26 no.4
• /
• pp.129-132
• /
• 2016

The effect of thermal-nitrification on L1o transfomation in nano-sized FePt particles was studied. As-synthesized FePt nanoparticles by thermal decomposition method have fcc structured phase and their Hc and Ms were 247.34 Oe and 27.308 emu/g, respectively. According to the XRD analysis, phase transformation from fcc (face centered cubic) to fct (face centered tetragonal) structure was revealed by heating under $NH_3+H_2$ mixed-gas atmosphere. Also a slight shift of each (111) peak indicated phase transformation from fcc to fct structure. Hc and Ms of fct FePtN were 1058.2 Oe and 32.718 emu/g, respectively. The nano-sized FePtN magnetic particles synthesized by thermal decomposition method and mixed-gas nitrification are expected for advanced applications such as high density magnetic recording media and biomedical materials.

• Journal of Hydrogen and New Energy
• /
• v.24 no.5
• /
• pp.413-420
• /
• 2013

Effect of inherent volatile matters in fuels on electrochemical reactions of anode was investigated for a single direct carbon fuel cell (DCFC). Raw coals used as power source in the DCFC release light gases into the atmosphere under the operating temperature of DCFC ($700^{\circ}C$) by thermal decomposition and only char remained. These exhausted gases change the gas composition around anode and affect the electrochemical oxidation reaction of system. To investigate the effect of produced gases, comparative study was conducted between Indonesian sub-bituminous coal and its char obtained through thermal treatment, carbonizing. Maximum power density of raw coal ($52mW/cm^2$) was appeared higher than that of char ($37mW/cm^2$) because the gases produced from the raw coal during thermal decomposition gave additional positive results to electrochemical reaction of the system. The produced gases from coals were analyzed using TGA and FT-IR. The influence of volatile matters on anodic electrolyteelectrode interface was observed by the equivalent circuit induced from fitting of impedance spectroscopy data.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.13 no.4
• /
• pp.79-88
• /
• 2005

The wastes generated in farming or fishing villages are mostly those of high moisture content or those once used for farming or fishing work, which require a complex process even for disposing of them alone, and moreover they have been recognized to cause a secondary side effects. The study thus is intended to conduct the basic character analysis and incineration test so as to develop the thermal decomposition furnace which will be optimal in disposing of the wastes generated from urban area that mostly have a high thermal energy or require a complex treatment process. And the subject included in the study, in addition, is to design and develop the furnace aimed at reducing the harmful ingredient as well as recycling the heat generated in the course of incineration.

• Journal of the Korean Chemical Society
• /
• v.7 no.2
• /
• pp.96-105
• /
• 1963

The weight decrease curves of 18 kinds of polymers have been measured by thermobalance at the same condition where temperature is increased $1^{\circ}C$ per minutes under nitrogen or air atmosphere. The curves are further differentiated to obtain rate curve of weight decrease. Those curve offer a method to compare relative thermal stability, effects of oxygen or modes of thermal degradation of polymers qualitatively. The curves could be classified into following four types: Polystyrene, polymethylmethacrylate and acetal polymer belong to the first type. Those polymers depolymerize mainly into corresponding monomers, weight decrease curves are steepy up to perfect vaporization of polymers and rate curves show a relatively sharp peak. (Type I) Polyvinyl chloride represents the second type. This polymer decomposes with splitting off of hydrogen chloride. The thermogravimetric curve rises rapidly at first, then level off at the moderate weight decrease and gradually rises. Polyvinyl acetate also belongs to this class. (Type II) The modification of the second type is represented by polyester. The curve at the early stage is less steep, the leveling off at the next stage is less clear and the final rising of the curve is steeper than the normal second type. Polyamide, polyurethane, and polycarbonate belong to this type. (Type II') The thermal decomposition of the third type polymers is more complex than that of others. Various irregular chain scissions including side chain splitting and depolymerization to monomers occur simultaneously. The weight of the polymer decreases gradually and the rate curve does not show sharp peaks. Polyvinyl alcohol and diene polymers belong to this type. (Type III) Generally, polycondensation polymers are more stable toward heat than addition polymers and polymers having aromatic nucleus show good thermal stability. Polymers having tertiary carbon atoms such as polystyrene or polypropylene and acetal resin start decomposition under airatmosphere at the temprature below $50^{\circ}C$ or more of the temperature where the polymers start decomposition under nitrogen atmosphere.

• Resources Recycling
• /
• v.9 no.6
• /
• pp.15-22
• /
• 2000

There are many intensive efforts to develop the recycling technologies of waste plastics in steel works to tackle the saving of resources and the protection of the natural environment. In this study, the thermogravimetric analyses for three kinds of plastics, the combustion experiments and the theoretical approach for calculating the flame temperature in the blast furnace had been performed to understand the behavior of plastics in the raceway. The thermal decompositions of plastics were studied using thermogravimetric analyzer under the atmospheric condition. The starting temperature of thermal decomposition and the maximum weight loss point were increased in proportion to the logarithmic values of heating rate. The combustion characteristics of plastics were simulated in a coke-bed combustor. The combustion efficiency of plastics was lower than that of pulverized coal. The oxygen enrichment was found out to be one of the useful methods to increase the combustibility of plastics in raceway. The maximum injection rate of plastics was calculated based on the flame temperature.

• Nuclear Engineering and Technology
• /
• v.51 no.6
• /
• pp.1487-1503
• /
• 2019

The methods and performance of a pin-level nuclear reactor core thermal-hydraulics (T/H) code ESCOT employing the drift-flux model are presented. This code aims at providing an accurate yet fast core thermal-hydraulics solution capability to high-fidelity multiphysics core analysis systems targeting massively parallel computing platforms. The four equation drift-flux model is adopted for two-phase calculations, and numerical solutions are obtained by applying the Finite Volume Method (FVM) and the Semi-Implicit Method for Pressure-Linked Equation (SIMPLE)-like algorithm in a staggered grid system. Constitutive models involving turbulent mixing, pressure drop, and vapor generation are employed to simulate key phenomena in subchannel-scale analyses. ESCOT is parallelized by a domain decomposition scheme that involves both radial and axial decomposition to enable highly parallelized execution. The ESCOT solutions are validated through the applications to various experiments which include CNEN $4{\times}4$, Weiss et al. two assemblies, PNNL $2{\times}6$, RPI $2{\times}2$ air-water, and PSBT covering single/two-phase and unheated/heated conditions. The parameters of interest for validation include various flow characteristics such as turbulent mixing, spacer grid pressure drop, cross-flow, reverse flow, buoyancy effect, void drift, and bubble generation. For all the validation tests, ESCOT shows good agreements with measured data in the extent comparable to those of other subchannel-scale codes: COBRA-TF, MATRA and/or CUPID. The execution performance is examined with a mini-sized whole core consisting of 89 fuel assemblies and for an OPR1000 core. It turns out that it is about 1.5 times faster than a subchannel code based on the two-fluid three field model and the axial domain decomposition scheme works as well as the radial one yielding a steady-state solution for the OPR1000 core within 30 s with 104 processors.