• Smart Structures and Systems
• /
• 제24권3호
• /
• pp.361-377
• /
• 2019

The stiffness of shape memory alloy (SMA) spring while in actuation is represented by an empirical model that is derived from the logistic differential equation. This model correlates the stiffness to the alloy temperature and the functionality of SMA spring as active variable stiffness actuator (VSA) is analyzed based on factors that are the input conditions (activation current, duty cycle and excitation frequency) and operating conditions (pre-stress and mechanical connection). The model parameters are estimated by adopting the nonlinear least square method, henceforth, the model is validated experimentally. The average correlation factor of 0.95 between the model response and experimental results validates the proposed model. In furtherance, the justification is augmented from the comparison with existing stiffness models (logistic curve model and polynomial model). The important distinction from several observations regarding the comparison of the model prediction with the experimental states that it is more superior, flexible and adaptable than the existing. The nature of stiffness variation in the SMA spring is assessed also from the Dynamic Mechanical Thermal Analysis (DMTA), which as well proves the proposal. This model advances the ability to use SMA integrated mechanism for enhanced variable stiffness actuation. The investigation proves that the stiffness of SMA spring may be altered under controlled conditions.

• 한국의류산업학회지
• /
• 제24권6호
• /
• pp.812-824
• /
• 2022

This study proposes to develop a 3D printed re-entrant(RE) strip by shape memory thermoplastic polyurethane that can be deformed and recovered by thermal stimulation. The most suitable 3D printing infill density condition and temperature condition during shape recovery for mechanical behavior were confirmed. As the poisson's ratio indicated, the higher the recovery temperature, the closer the poisson's ratio to zero and the better the auxetic properties. After recovery testing for five minutes, it appeared that the shape recovery ratio was the highest at 70℃. The temperature range when the shape recovery ratio appeared to be more than 90% was a recovery temperature of more than 50℃ and 60℃ when deformed under a constant load of 100 gf and 300 gf, respectively. This indicated that further deformation occurred after maximum recovery when recovered at a temperature of 80℃, which is above the glass transition temperature range. As for REstrip by infill density, a shape recovery properties of 100% was superior than 50%. Additionally, as the re-entrant structure exhibited a shape recovery ratio of more than 90%, and exhibited auxetic properties. It was confirmed that the infill density condition of 100% and the temperature condition of 70℃ are suitable for REstrips for applying the actuator.

• 한국정밀공학회지
• /
• 제30권3호
• /
• pp.254-259
• /
• 2013

Ball screw system is widely used as a precision mechanical linear actuator that translates rotational motion to linear motion for its high efficiency, great stiffness and long life. Recently, according to the requirements of high accuracy and stiffness, the pre-load on the ball screw which means of remove the backlash in the ball screw is usually used. Because of the preload which means the frictional resistance between the screw and nut, becomes a dominating heat source and it generates thermal deformation of ball screw which is the reason for low accuracy of the positioning decision. There are several methods to solve the problem that includes temperature control, thermal stable design and error compensation. In the past years, researchers focused on the error compensation technique for its ability to correct ball screw error effectively rather than the capabilities of careful machine design and manufacturing. Significant amounts of researches have been done to real-time error compensation. But in this paper, we developed a series of cooling methods to get thermal equilibrium in the ball screw system. So we find the optimum cooling type for improving positioning error which caused by thermal deformation in the ball screw system.

• 한국시뮬레이션학회논문지
• /
• 제23권2호
• /
• pp.17-24
• /
• 2014

본 논문은 항공기용 EHA의 열유동 해석모델을 개발하고 활용하는 사례를 보여준다. 연구진행 절차는 다음과 같다. 첫째, 설계 컨셉에 맞는 물리량을 반영하는 유압단품 해석모델을 개발한다. 둘째, 유압단품 모델을 조합하여 EHA 유압모델로 확장한다. 셋째, 열유동이 포함된 해석모델을 개발하여 초기온도와 부하의 변화에 따른 유온의 상승시간을 검토한다. 마지막으로, 여러 케이스의 열유동 해석결과가 조합된, 설계에 활용이 가능한 지배그래프를 작성하여 제안한다. 이 모든 과정은 상용 소프트웨어인 AMEsim을 사용하여 진행한다.

• 한국항공우주학회지
• /
• 제35권5호
• /
• pp.390-396
• /
• 2007

본 연구에서는 새의 날개운동을 모사하기 위하여 스마트 재료를 이용한 플래핑 날개를 설계 및 제작하였다. 날개는 복합재료 프레임과 유연한 PVC 표피 그리고 표면 작동기로 구성되어 있으며, 주요 날개운동으로서 날갯짓, 비틀림 그리고 캠버 운동을 선정하였다. 날개의 캠버를 변화시키기 위하여 Macro-Fiber Composite를 표면작동기로서 적용하였으며, 압전-열 관계식을 이용하여 MFC의 구조 응답을 해석하였다. 양력과 추력을 동시에 측정하기 위하여 두개의 로드셀로 구성된 시험대를 제작하였으며, 공기역학적 특성을 평가하기 위하여 풍동실험을 수행하였다. 실험결과로부터 주요 양력은 기체의 전진속도와 피치각에 의존되며, 추력은 날갯짓 주파수에 의존됨을 확인하였다. 또한 MFC 작동기를 이용한 캠버효과를 통하여 정적조건에서 24.4%와 동적조건에서 20.8%의 충분한 양력증가를 확인할 수 있었다.

• International Journal of Aerospace System Engineering
• /
• 제9권2호
• /
• pp.1-9
• /
• 2022

The NEA release mechanism is used to provide restraint and release functions with low shock for critical deployment operations on solar arrays after launch. The GK3 solar array consists of 2 wings and 6 hold down points per panel. The NEA SSD9103S1 is a part of the GK3 solar array hold-down and release mechanism. Each NEA unit is equipped with two Z-diodes which provide power to a NEA unit connected in series after actuation of the fuse wire. This paper presents the hot firing test results of a quadrature NEA SSD9103S1 configuration. One output powers a maximum of 4 NEA SSD9103S1 units simultaneously. The necessary actuation pulse duration has been determined to meet margin requirement for thermal energy of minimum 4. Actuation thermal energy difference is about 6.6% between each half of two fired serial NEAs. Thermal energy margin at worst case is minimum 5.9 in case of an actuation pulse duration of 500 ms. Two series Zener impedance depend on current applied has been characterized by an additional actuation after all fuse wires are open circuit. Total number of actuation commands to the GK3 NEA unit reduce drastically from 24 in case of single NEA configuration down to 8 in case of parallel and quadrature NEA configurations. It can be accommodated by the existing HP2U Pyro design without any impact.

• 한국소음진동공학회논문집
• /
• 제27권2호
• /
• pp.168-174
• /
• 2017

In this work, a piezostack single-stage valve (PSSV) system is proposed and its control performance is experimentally evaluated at high temperature up to $150^{\circ}C$. In order to achieve this goal, a PSSV system is designed and operating principle and mechanical dimensions are discussed. A displacement amplifier and an adjust bolt are used to generate target displacement and to compensate thermal expansion. Then, an experimental apparatus is constructed to evaluate control performance of the PSSV system. The experimental apparatus consists of a heat chamber, a hydraulic circuit, a pneumatic circuit, pneumatic-hydraulic cylinders, thermal insulator, electronic devices, sensors, data acquisition (DAQ) board and a voltage amplifier. The flow rate and displacement control performance of the valve system are evaluated via experiment. The experimental results are evaluated and discussed at different temperatures and frequencies showing the controlled flow rate and spool displacement.

• Structural Engineering and Mechanics
• /
• 제58권5호
• /
• pp.931-947
• /
• 2016

The effects of nanotechnology and smartness on the buckling reduction of pipes are the main contributions of present work. For this ends, the pipe is simulated with classical piezoelectric polymeric cylindrical shell reinforced by armchair double walled boron nitride nanotubes (DWBNNTs), The structure is subjected to combined electro-thermo-mechanical loads. The surrounding elastic foundation is modeled with a novel model namely as orthotropic nonhomogeneous Pasternak medium. Using representative volume element (RVE) based on micromechanical modeling, mechanical, electrical and thermal characteristics of the equivalent composite are determined. Employing nonlinear strains-displacements and stress-strain relations as well as the charge equation for coupling of electrical and mechanical fields, the governing equations are derived based on Hamilton's principal. Based on differential quadrature method (DQM), the buckling load of pipe is calculated. The influences of electrical and thermal loads, geometrical parameters of shell, elastic foundation, orientation angle and volume percent of DWBNNTs in polymer are investigated on the buckling of pipe. Results showed that the generated ${\Phi}$ improved sensor and actuator applications in several process industries, because it increases the stability of structure. Furthermore, using nanotechnology in reinforcing the pipe, the buckling load of structure increases.

• Smart Structures and Systems
• /
• 제8권3호
• /
• pp.275-302
• /
• 2011

This is a review paper on mathematical modeling of actively controlled piezo smart structures. Paper has four sections to discuss the techniques to: (i) write the equations of motion (ii) implement sensor-actuator design (iii) model real life environmental effects and, (iv) control structural vibrations. In section (i), methods of writing equations of motion using equilibrium relations, Hamilton's principle, finite element technique and modal testing are discussed. In section (ii), self-sensing actuators, extension-bending actuators, shear actuators and modal sensors/actuators are discussed. In section (iii), modeling of thermal, hygro and other non-linear effects is discussed. Finally in section (iv), various vibration control techniques and useful software are mentioned. This review has two objectives: (i) practicing engineers can pick the most suitable philosophy for their end application and, (ii) researchers can come to know how the field has evolved, how it can be extended to real life structures and what the potential gaps in the literature are.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.372-373
• /
• 2008

The snap-through phenomena of the curved IPMC actuators were investigated according to the initial curvature of the actuators. The curved actuators were fabricated by long time thermal treatments. Cantilevered IPMCs have a constant curvature and their initial tip-displacements are 0, 8, and 16mm, respectively. These actuators were tested in terms of f response. AC response, FRF test for evaluating the effect of initial shape. The hysteresis and instant speed of tip point were measured for observation of the snap-through. Present results show that initial deformation strongly affects the snap-through phenomena, resulting in much larger tip-displacements.