• Korean Journal of Materials Research
• /
• v.24 no.10
• /
• pp.565-571
• /
• 2014

Nitrogen-doped ZnO nanoparticle-carbon nanofiber composites were prepared using electrospinning. As the relative amounts of N-doped ZnO nanoparticles in the composites were controlled to levels of 3.4, 9.6, and 13.8 wt%, the morphological, structural, and chemical properties of the composites were characterized by means of field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). In particular, the carbon nanofiber composites containing 13.8 wt% N-doped ZnO nanoparticles exhibited superior catalytic properties, making them suitable for use as counter electrodes in dye-sensitized solar cells (DSSCs). This result can be attributed to the enhanced surface roughness of the composites, which offers sites for $I_3{^-}$ ion reductions and the formation of Zn3N2 phases that facilitate electron transfer. Therefore, DSSCs fabricated with 13.8 wt% N-doped ZnO nanoparticle-carbon nanofiber composites showed high current density ($16.3mA/cm^2$), high fill factor (57.8%), and excellent power-conversion efficiency (6.69%); at the same time, these DSSCs displayed power-conversion efficiency almost identical to that of DSSCs fabricated with a pure Pt counter electrode (6.57%).

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.6
• /
• pp.1138-1150
• /
• 1996

This study was carried out to investigate the effects of dyeing on the mechanical properties, primary hand, total hand value (THV), and total appearance value (TAV) of woven fabrics. Cotton, PET, nylon, cotton/PET, and cotton/nylon woven fabrics were used as test specimens. Each of fabric was dyed under the same conditions as the fabrics for sportswear which consumers have selected as best. Mechanical properties of specimens were measured by KES-FB system and primary hand and THV were calculated by equation KN -201-MDY and KN-301-WINTER respectively. TAV was calculated by KN (eq. 10). The results were as follows: 1. In mechanical properties. tensile energy increased when cotton and two cotton mixture fabrics were dyed and decreased when polyester and nylon fabrics were dyed. Bending rigidity and shear rigidity decreased after all fabrics were dyed except nylon and cotton/ nylon mixture fabrics showing higher rigidities. Cotton fabrics showed higher surface roughness while other fabrics did lower values after dyeing. 2. In evaluation of primary hand and total hand , four primary hands of cotton fabrics so decreased after dyeing that THV were lowered. Numeri, Fukurami, and Sofutosa in primary hand of polyester, cotton/polyester, and cotton/nylon fabrics and Koshi and Numeri of nylon fabrics increased after dyeing and therefore THV of four fabrics were improved. 3. Cotton and polyester fabrics showed higher TAV due to their lower bending and shear rigidity, while nylon and cotton/nylon fabrics did lower values due to their higher shear rigidity. 4. It was proposed that the method of dyeing or treatment for minimizing the decrease of THV of cotton fabrics and TAV of nylon fabrics should be developed.

• Journal of Adhesion and Interface
• /
• v.16 no.3
• /
• pp.116-121
• /
• 2015

In this study, octadecyltrichlorosilane (OTS) has been used to replace fluoro-silanes which are much more expensive than OTS. In order to improve the mechanical and adhesive properties of coating layers, inorganic binders were separately synthesized based on sol-gel reaction in acidic condition. Since the synthesized silica nanoparticles gave only nano-scaled roughness, superhydrophobicity is not well obtained. Here, we present a new simple approach by intentionally inducing particle aggregation in the solution which is controlled by adjusting solvent amount. With selecting suitable sizes of silica nanoparticles, superhydrophobic surfaces were obtained with increasing the amount of organic solvents after surface hydrophobization using OTS, and an extremely water-repellent behavior was observed with zero sliding angle. This superhydrophobicity was achived only for the dielectric constant lower than 25, regardless of the composition of solvent, meaning that the dielectric constant could be an excellent indicator for fabricating superhydrobic surfaces induced by particle aggregation in the solution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.9
• /
• pp.589-593
• /
• 2014

AlNO multi-layer thin films on aluminum substrates were prepared by DC reactive magnetron sputtering method. $Al_2O_3$/AlNO(LMVF)/AlNO(HMVF)/Al/substrate of 4 multi-layer has been prepared in an Ar and ($N_2+O_2$) gas mixture, and $Al_2O_3$ of top layer is anti-reflection layer on double AlNO(LMVF)/AlNO(HMVF) layers and Al metal of infrared reflection layer. In this study, the roughness and surface properties of AlNO thin films were estimated by field emission scanning electron microscopy(FE-SEM). The grain size of AlNO thin films increased with increasing sputtering power. The composition of thin films has been systematically investigated using electron probe microanalysis(EPMA). The optical properties with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at a range of 200~1,500 nm. The absorptance of AlNO films shows the increasing trend with swelling ($N_2+O_2$) gas mixture in HMVF and LMVF deposition. The excellent optical performance showed above 98% of absorptance in visible wavelength region.

• Journal of Korea Water Resources Association
• /
• v.38 no.9 s.158
• /
• pp.699-711
• /
• 2005

In this study, the U.S. Geological Survey's DR3M-II(Distributed Routing Rainfall-Runoff Model) was applied for small urban drainage. DR3M-II is a watershed model for routing storm runoff through a branched system of pipes and natural channels using rainfall input. The model was calibrated and verified using short term rainfall-runoff data collected from Sanbon basin. Also, the parameters were optimized using Rosenbrock technic. An estimated simulation error for peak discharge was about 7.4 percent and the result was quite acceptable. Results of the sensitivity analysis indicate that the percent of effective impervious area and ${\alpha}$ defining surface slope and roughness were the most sensitive variables affecting runoff volumes and peak discharge for low and high intensity storm respectively. In most cases, soil moisture accounting and infiltration parameters are the variables that give more effects to runoff volumes than peak discharge. Parameter ${\alpha}$ showed the opposite result.

• Journal of Hydrogen and New Energy
• /
• v.18 no.4
• /
• pp.391-398
• /
• 2007

The covalently cross-linked sulfonated polyetheretherketone (CL-SPEEK) membrane was prepared by four-step synthesis of sulfonation-sulfochlorination, partial reduction, lithiation, and cross-linking, and its electrochemical and mechanical properties were investigated for water electrolysis application. The prepared ion exchange membranes showed good electrochemical and mechanical properties; proton conductivity of 0.116 S/cm at $80^{\circ}C$, water uptake of 44.6%, ion exchange capacity of 1.75 meq/g-dry-memb., tensile strength of 64.25 MPa and elongation of 61.11%. The membrane electrode assembly (MEA) with homemade membranes were prepared by non-equilibrium impregnation-reduction (I-R) method. Especially, the electrochemical surface area (ESA) and roughness factor of CL-SPEEK electrolyte by cyclic voltammetry method were 23.46 $m^2/g$ and 307.3 $cm^2-Pt/cm^2$, respectively. The prepared MEA was used in the unit cell of water electrolysis and the cell voltage was 1.81 V at 1 A/$cm^2$ and $80^{\circ}C$, with platinum loadings of 1.31 mg/$cm^2$.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.359-363
• /
• 2005

The organic insulation devices with MIM (metal-insulator-metal) structures as PVP gate insulation films were prepared for the application of organic thin film transistors (OTFT). The co-polymer organic insulation films were synthesized by using PVP(poly-4-vinylphenol) as solute and PGMEA (propylene glycol monomethyl ether acetate) as solvent. The cross-linked PVP insulation films were also prepared by addition of poly (melamine-co-formaldehyde) as thermal hardener. The leakage current of the cross-linked PVP films was found to be about 300 pA with low current noise. and showed better property in electrical properties as compared with the co-polymer PVP insulation films. In addition, cross-linked PVP insulation films showed better surface morphology (roughness), showing about 0.11${\~}$0.18 nF in capacitance for all PVP film samples.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.7-12
• /
• 2010

In this paper, $C_{60}$ based Organic thin film transistor OTFTs) have been fabricated using BPhen(Bathophenanthroline) and BPhen doped with Cs interlayers between $C_{60}$ active layer and Al electrodes to improve the electrical performance. The addition of the BPhen layer resulted in enhanced performances by reducing surface roughness between organic-metal interface. And the contact resistance was reduced by using the BPhen doped with Cs interlayer with co-evaporation method. These performances suggests that the $C_{60}$ based OTFT with BPhen doped with Cs interlayer is a promising application in the fabrication of n-type organic transistors.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.89-94
• /
• 2019

Glass base sealant is required as a ceramic-ceramic joining material between α-alumina insulation cap and β-alumina electrolyte tube in the development of NaS battery cell package for electrical energy storage system. The fabrication of glass frit by thermal quenching method, phase analysis, particle size analysis, coefficient of thermal expansion and surface roughness according to the glass compositions were analyzed for the fabrication of glass sealing paste for ceramic-ceramic joining. Also, a new evaluation method of the adhesion strength of glass sealant at the small area in ceramic-ceramic joining component was proposed using conventional Dage bond tester that was used to measure the adhesion of solder ball joint.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.442-443
• /
• 2006

Electrical, optical, surface, and structural properties of amorphous indium zinc oxide (IZO) films grown on $SiO_2$/PES/$SiO_2$ substrate by a RF sputtering in pure Ar ambient at room temperature were investigated. A sheet resistance of $13.5\;{\Omega}{\square}$, average transmittance above 85 % in 550 nm, and root mean square roughness of $10.5\;{\AA}$ were obtained even in the IZO layers grown at room temperature in pure Ar ambient. Without addition of oxygen gas during IZO sputtering process, we can obtain high quality IZO anode films from the specially synthesized oxygen rich IZO target. XRD result shows that the IZO films grown at room temperature is completely amorphous structure due to low substrate temperature. In addition, the electrical and optical properties of the flexible OLED fabricated on IZO/$SiO_2$/PES/$SiO_2$ is critically influenced by the electrical properties of a IZO anode. This findings indicate that the IZO/$SiO_2$/PES/$SiO_2$ is a promising anode/substrate scheme for realizing organic based flexible displays.