• 비파괴검사학회지
• /
• 제28권6호
• /
• pp.477-482
• /
• 2008

The influence of dislocation substructure of metallic materials on ultrasonic velocity has been experimentally investigated. The test materials of pure Cu, brass (Cu-35Zn), 2.25Cr-1Mo steel, and AISI 316 with different stacking fault energy (SFE) are plastically deformed in order to generate dislocation substructures. The longitudinal wave velocit $(C_L)$ decreases as a function of tensile strain in each material. The $C_L$ of Cu-35Zn and AISI 316 decreases monotonously with tensile strain, but $C_L$ of Cu and 2.25Cr-1Mo steel shows plateau phenomena due to the stable dislocation substructure. The variation of ultrasonic velocity with the extent of dislocation damping and dislocation substructures is discussed.

• Interaction and multiscale mechanics
• /
• 제6권2호
• /
• pp.127-136
• /
• 2013

In this study, atomistic simulations are performed to study the effect of Al solute on the behaviour of edge dislocation in Mg alloys. After the dissociation of an Mg basal edge dislocation into two Shockley partials using molecular mechanics, the interaction between the dislocation and Al solute at different temperatures is studied using molecular dynamics. It appears from the simulations that the critical shear stress increases with the Al solute concentration. Comparing with the solute effect at T = 0 K, however, the critical shear stress at a finite temperature is lower since the kinetic energy of the atoms can help the dislocation conquer the energy barriers created by the Al atoms. The velocity of the edge dislocation decreases as the Al concentration increases when the external shear stress is relatively small regardless of temperature. The Al concentration effect on the dislocation velocity is not significant at very high shear stress level when the solute concentration is below 4.0 at%. Drag coefficient B increases with the Al concentration when the stress to temperature ratio is below 0.3 MPa/K, although the effect is more significant at low temperatures.

• 한국재료학회지
• /
• 제11권3호
• /
• pp.221-226
• /
• 2001

사파이어 ($\alpha$-$Al_2$$O_3$) 단결정에 있어 basal slip (0001)1/3<1120>의 전위속도를 4점 곡강도를 이용하여, 측정하였다. 이 곡강도는 온도 $1200^{\circ}C$ 에서 $1400^{\circ}C$ 그리고 응력은 90MPa, 120MPa, 160MPa에서 행하여졌다. 전위속도는 4 점굽힘 시편의 굽힘변위속도에 의해 구하여졌다. 얻어진 전위속도를 이용하여 전위속도의 온도 및 응력 의존성에 대해 검토하였다. 전위속도의 온도의존성을 이용하여 basal slip 전위속도를 위한 활성화에너지를 구하였으며, 그 값은 대략 2.2$\pm$0.4eV이었다. 한편, 전위속도의 응력의존성을 나타내는 응력지수 m은 2.0$\pm$0.2이었다.

• 대한기계학회논문집A
• /
• 제26권7호
• /
• pp.1317-1323
• /
• 2002

This paper describes the comparison of calculated effective stress with experimental one in austenitic heat resistant steels, STS310J1TB and STS310S with and without a small amount of Nb and N. Based on a solute atoms diffusion model, contribution from soluble nitrogen to the high-temperature strength was numerically examined for austenitic heat-resisting Fe-Cr-Ni-N(STS310J1TB) and Fe-Cr-Ni (STS310S) alloys. The solute atmosphere dragging stress of dislocation was calculated in optional dislocation velocity of STS310J1TB and STS310S at $650^{\circ}C$, $675^{\circ}C$ and $700^{\circ}C$. As a result of the numerical calculation, the solute atmosphere dragging stress of STS310J1TB was about 50 times larger than that of STS310S. When the temperature became high, the maximum value of solute atmosphere dragging stress was small and the velocity of moving dislocation was fast. From the relationship between the dislocation rate and the solute atmosphere dragging stress, the relation of both was proportional and the inclination is about 1 in the level with low velocity of moving dislocation. From above results, the mechanism of dislocation movement in STS310J1TB was the solute atmosphere dragging stress. The solute atmosphere dragging stress, which was calculated from the numerical calculation was close to the effect stress in stress relaxation tests.

• 한국결정성장학회지
• /
• 제10권4호
• /
• pp.337-343
• /
• 2000

사파이어 ($\alpha$-Al$_2$O$_3$) 단결정에 있어 prism plane slip {11$\bar{2}$0}1/3{$\bar{1}$120} 전위속도를 에치-피트 방법으로 측정하였다. 전위속도 측정시 온도범위는 $1150^{\circ}C$에서 $1400^{\circ}C$까지 였으며, 응력범위는 140 MPa에서 250 MPa까지였다. 얻어진 전위속도의 온도 및 응력 의존성에 대해 검토하였다. 전위속도의 온도의존성을 이용하여 prism plane slip 전위속도를 위한 활성화에너지를 구하였으며, 그 값은 대략 4.2$\pm$0.4 eV이었다. 또한, 전위속도의 응력의존성을 나타내는 응력지수 m은 4.5$\pm$0.8이었다. 한편, 전위속도 측정을 통해 사파이어 단결정에서 basal 면이 3-fold 대칭을 가진다는 사실을 재확인하였다.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.262-262
• /
• 1990

In order to check the effect of dislocation behavior on creep rate in 12% Chromium steel, 14 samples of different compositions were examined by creep rupture test, and subgrain sizes, distribution of dislocations and precipitates were checked. And, authors reviewed the behaviors of dislocations, the formation and growth of subgrains and precipitates during creep. The results are as the following: 1) Creep rates calculated by .epsilon. over dot = .rho.bv show 10-15% higher values than actual data measured. However, authors conclude that the density and velocity of dislocations together with subgrain size are important factors governing deformation during creep in 12% chromium steel. 2) The values of the strength of obstacles in the mobility of dislocations are more clearly depended on the effective stress in the range of $10{\pm}5kgf/mm^{2}$ and increase with the increase of temperature. 3) Creep rates decrease with the smaller sizes of subgrains formed and can result in the longer creep rupture lives(hours). The smaller subgrains can be made by forming shorter free gliding distances of dislocations with very fine precipitates formed in the matrix during creep by applying proper alloy design. 4) Dislocation mobility gets hindered by precipitates occurring, which are coarsened by the softening process governed by diffusion during long time creep.

• 한국해양공학회지
• /
• 제4권2호
• /
• pp.112-120
• /
• 1990

In order to check the effect of dislocation behavior on creep rate in 12% Chromium steel, 14 samples of different compositions were examined by creep rupture test, and subgrain sizes, distribution of dislocations and precipitates were checked. And, authors reviewed the behaviors of dislocations, the formation and growth of subgrains and precipitates during creep. The results are as the following: 1) Creep rates calculated by .epsilon. over dot = .rho.bv show 10-15% higher values than actual data measured. However, authors conclude that the density and velocity of dislocations together with subgrain size are important factors governing deformation during creep in 12% chromium steel. 2) The values of the strength of obstacles in the mobility of dislocations are more clearly depended on the effective stress in the range of $10{\pm}5kgf/mm^{2}$ and increase with the increase of temperature. 3) Creep rates decrease with the smaller sizes of subgrains formed and can result in the longer creep rupture lives(hours). The smaller subgrains can be made by forming shorter free gliding distances of dislocations with very fine precipitates formed in the matrix during creep by applying proper alloy design. 4) Dislocation mobility gets hindered by precipitates occurring, which are coarsened by the softening process governed by diffusion during long time creep.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.296-301
• /
• 2004

By the purpose to investigate the change of internal stress and mobile dislocation density in creep, the stress relaxation test is carried out in the condition of each strain. Mobile dislocation density increased until it reached minimum creep rate and after that, it decreased and internal stress didn't have the change approximately until it reached minimum creep rate and after that, it decreased. The stress relaxation rate is fast and approached zero after 1.5 seconds after the beginning of the stress relaxation. And the larger the applied stress is, the larger the internal stress is. By the evaluation of mobility of dislocation, the dislocations glide viscously in STS31OJlTB but it is the dislocations glide viscously which N passes by cutting Cr atom rather than typical viscosity movement after calculating mobility of dislocation.

• 비파괴검사학회지
• /
• 제31권1호
• /
• pp.32-39
• /
• 2011

본 연구에서는 Cu와 Cu-Zn 합금의 저주기 피로 동안 발달한 전위 하부조직의 변화를 비파괴적으로 구분하고 평가하고자 하였다. 비파괴시험으로 초음파속도, 전기비저항 그리고 양성자소멸시간을 측정하였다. 서로 다른 적층결함 에너지를 갖는 Cu와 Cu-Zn에 대해 반복피로시험을 수행하고 이들 재료에서의 전위거동과 비파괴평가 파라미터와의 상관성을 연구하였다. Cu는 전위셀 하부구조를 형성하였지만, Cu-Zn 합금은 피로 사이클에 따라서 전위밀도는 증가하고 단지 평면배열의 전위구조를 형성하였다. 상온에서의 반복적인 피로에 의해 발달한 격자결함인 전위와 공공으로 인해 초음파속도의 감소, 전기비저항의 증가 그리고 양성자 소멸시간이 증가하였다. 비파괴평가파라미터의 지속적인 변화를 보이는 평면배열의 전위구조를 갖는 Cu-Zn에서와 달리, Cu에서는 전위셀구조가 발달하면서 더 이상의 큰 변화를 보이지 않았다.

• 한국재료학회지
• /
• 제11권6호
• /
• pp.508-511
• /
• 2001

사파이어 단결정의 취성-연성전이에 대한 실험을 행하였다. 사파이어 단결정의 취성-연성전이온도는 변형율 3.3$\times$ $10^{-5}$/sec에서 $1000\pm$$25^{\circ}C$ 그리고 변형률 3.3$\times$$10^{-5}$/sec에서는 1100$\pm$26$^{\circ}C$이었다. 취성-연성전이모델을 이용하여 Prism Plane slip {1120} <1100> 전위속도의 활성화에너지를 계산하였으며, 그 결과 활성화에너지는 4.6$\pm$2.3eV의 범위를 가졌다. 이 활성화에너지는 에치-퍼트법을 이용하여 전위속도측정으로부터 구한 결과치 3.8eV와 유사하였다.