• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 센서 박막재료 반도체 세라믹
• /
• pp.154-157
• /
• 2003

$TiO_2$ thin films were fabricated by RF magnetron sputtering system at by controlling deposition times, ratios of $Ar:O_2$ partial presser ratio and substrate conditions. And the surface, cross-section morphology, microstructure, and composition ratio of the films were analyzed by FE-SEM, TEM and XPS. Besides, the optical absorption and transmittance of the $TiO_2$ films were measured by a UV-VIS-NIR Spectrophotometer, and photocatalytic properties were studied by G${\cdot}$C Analyzer & Data Analysis system. As the result, when $TiO_2$ thin film was made at deposition time of 120[min] and $Ar:O_2$ ratio of 60:40, the best structural and optical properties among many thin films could be accepted. The best results of properties were as follows: thickness; 360~370[nm), grain size; 40[nm], gap between two peak binding energy; $5.8{\pm}0.05[eV]$ ($2_{p3/2}$ peak and $2_{p1/2}$ peak of Ti was show at $458.3{\pm}0.05[eV]$ and $464.1{\pm}0.05[eV]$ respectively), binding energy; $530{\pm}0.05[eV]$, optical energy band gap; 3.4[eV].

• 농약과학회지
• /
• 제17권4호
• /
• pp.271-282
• /
• 2013

본 연구는 2009년도부터 2012년까지 4년간 농협중앙회를 통해 농산물우수관리제도(GAP) 인증을 받은 농산물의 농약잔류실태를 평가하기 위하여 잔류농약다성분분석법에 따라 GC(ECD, NPD)와 HPLC를 이용하여 283종의 잔류농약을 분석하였다. 이 기간 동안 6,590점의 GAP 인증 농산물을 분석한 결과 잔류농약의 검출율은 2009년, 20.27%, 2010년, 23.42%, 2011년, 28.07% 및 2012년, 31.75%였으며, 부적합율은 2009년, 2.25%, 2010년, 1.82% 2011년, 1.67% 및 2012년, 3.47% 로 나타났다. 잔류허용기준을 초과한 농약은 carbendazim 등 12종 이었고, 미적용 농약 사용으로 인한 부적합 성분은 endosulfan을 비롯하여 40종 이었다. 대부분의 농산물에서 농약이 잔류허용기준 이내로 나타났기 때문에 안전하다고 보이지만 딸기에서 검출된 endosulfan 과 같이 해당작물에 대한 등록되지 않은 농약사용으로 인한 부적합이 127건, 사과에서 검출된 carbendazim 같이 허용기준 초과로 인한 부적합이 총 25 건이 발생하여 향후 GAP 농산물의 생산단계에서 농약사용에 대한 지속적인 관리가 필요할 것으로 사료된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.88-88
• /
• 2010

We synthesized molybdenum thin films deposited by RF magnetron sputtering and physicochemical analysis was performed. The physical and chemical properties of these films were examined with X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The obtained film at the oxygen ratio of 0% showed crystallinity of cubic Mo(110) phase. After the oxygen ratio increased more than 5% in the sputter gas, the molybdenum films were formed as an amorphous phase. The thickness of the Mo thin film was drastically decreased from 1000 nm to ca 70 nm after introduction of oxygen in the sputter gas confirmed by spectroscopic ellipsometer (SE) and scanning electron spectroscopy (SEM). The calculated band gap of the film deduced from SE data increased from 3.17 to 3.63 eV by addition of oxygen in the sputter gas. The roughness of the Mo film was examined with atomic force microscopy (AFM) and it was dramatically decreased by introducing of oxygen during sputtering. XPS results revealed that the ratio of metallic Mo species in the film decreased by the contents of Mo(VI) species increased at the ratio of oxygen increased in the sputter gas and fully oxidized at low content of oxygen in the sputter gas.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.207-213
• /
• 1996

A ternary compound semiconductor $Al_{x}$-Ga/1-x/Sb crystals which have energy gap from 0.7eV to 1.6ev at room temperature with the composition ratio were grown by using the vertical Bridgman method. The characteristics of $Al_{x}$-Ga/1-x/Sb were investigated in this study. The lattice constants of $Al_{x}$-Ga/1-x/Sb crystals with the composition ratio were appeared from 6.096$\AA$ to 6.135$\AA$ with the composition ratio. The electrical properties of the $Al_{x}$-Ga/1-x/Sb crystals measured the Hall effect by van der Pauw method at the magnetic field of 3 kilogauss and at room temperature. The resistivity of Te-doped $Al_{x}$-Ga/1-x/Sb crystals increased from 0.771 $\Omega$-cm to 5 $\Omega$-cm at room temperature with increasing the composition ratio. The mobility of Te-doped $Al_{x}$-Ga/1-x/Sb crystals varied with the composition ratio x, within the following three different regions, such as GaSb-like (0$\leq$x$\leq$0.3), intermediate (0.3$\leq$x$\leq$0.4) and AlSb-like (0.4$\leq$x$\leq$1).eq$1).

• Journal of Ecology and Environment
• /
• 제41권9호
• /
• pp.246-255
• /
• 2017

Background: The aim of this study was to examine the resource allocation among the organs and the leaf morphology of Polygonatum humile. The data were collected from June 2014 to May 2015 in a natural P. humile stand of a temperate forest gap. Results: The dry weight of new rhizome ($R_0$) sharply decreased to the time of new shoot sprouting in next year and was constant for 2 ~ 3 years. However, dry weight of root on $R_0$ increased to the end of growth season and, thereafter, decreased slowly along the time elapsed. The correlation coefficients between the rhizome and the leaf sizes were 0.5 for the last year's rhizome ($R_1$) and 0.6 for $R_0$ and were significant at 0.1% level for $R_0$. The increase of one leaf a plant led to increase of the total leaf area, total leaf weight, and stem length. Moreover, the organ sizes' differences between two plants of the one leaf difference were almost significant at 1% level. In 11-leaf plant, the leaf length/width ratio and specific lea area increased to the second, relative leaf area to the fourth and relative leaf dry weight to the fifth, and thereafter, decreased to the last leaf. The differences in the values of these four parameters between two leaves on a stem were almost significant at 5% level. Conclusion: P. humile examined showed the close relationships between the last year's rhizome or this year's one and the shoot system (leaf and stem) sizes. The leaf number a shoot greatly influenced specific leaf area. P. humile's leaf might showed diverse morphology with leaf rank on a stem in a forest gap environment.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권2호
• /
• pp.132-139
• /
• 2000

This paper reports a novel micromachining process based on UV-LIGA process and (110) silicon anisotropic etching for fabrication of a high-aspect-ratio comb actuator. The comb electrodes are fabricated by (110) SILICON comb structure considering the etch-rate-ratio between (110) and (111) planes and lateral etch rate of a beam-type structure. The fabricated structure was$ 400\mum \; thick\; and\; 18\mum$ wide comb electrodes separated by $7\mim$ so that the height-gap ratio was about 57. Also considering resonant frequency of the comb actuator and the frequency-matching between sensing and driving mode for gyroscope application, we designed the number, width, height and length of the spring structures. Electroplated gold springs on both sides of the seismic mass were $15\mum\; wide,\; 14\mum\; thick\; and \; 500\mum$ long. The fabricated comb actuator had resonant frequency ay 1430Hz, which was calculated to be 1441Hz. The proposed fabrication process can be applicable to the fabrication of a high-aspect-ratio comb actuator for a large displacement actuator and precision sensors. Moreover, this combined process enables to fabricate a more complex structure which cannot be fabricate only by surface or bulk micromachining.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1306-1317
• /
• 2018

For determining the in-plane buckling resistance of a concrete-filled steel tubular (CFST) arch, the current technical code GB50923-2013 specifies the use of an equivalent beam-column method which ignores the effect of rise-to-span ratio. This may induce a gap between the calculated result and actual stability capacity. In this study, a FE model is used to predict the buckling behavior of CFST truss arches subjected to uniformly distributed loads. The influence of rise-to-span ratio on the capacity of truss arches is investigated, and it is found that the stability capacity reduces as rise-to-span ratio declines. Besides, the calculations of equivalent slenderness ratio for different truss sections are made to consider the effect of shear deformation. Moreover, based on FE results, a new design equation is proposed to predict the in-plane strength of CFST parabolic truss arches under uniformly distributed loads.

• 대한지역사회영양학회지
• /
• 제28권2호
• /
• pp.95-103
• /
• 2023

Objectives: The budget gap in the health sector of local governments affects the supply of health services, which can cause the health gap. This study classified local governments according to their financial characteristics, such as local financial independence and health budget level. It analyzed the health behaviors and disease prevalence of local residents to examine the effect of local government financial investment on the health of local residents. Methods: To classify types according to the financial characteristics of local governments, financial independence and the health budget data for 17 local governments were collected from the local fiscal yearbook of the Ministry of Public Administration and Security. The prevalence of chronic diseases and healthy behavior was compared using the 16,333 data of adults between the ages of 30 and 65 years among the original data of the National Health and Nutrition Examination Survey (2016-2020). Results: Cluster analysis was used to classify local governments into five clusters according to the health financial capacity type. A comparison of the prevalence of local residents by cluster revealed a similar prevalence of hypertension, diabetes, and hypercholesterolemia. On the other hand, the obesity rate (P < 0.01), high-risk drinking rate (P < 0.01), aerobic physical activity rate (P < 0.001), and healthy eating practice rate (P < 0.001) were significantly different. In addition, an analysis of the odds ratio based on the Seoul area revealed a higher risk of health behavior of non-Seoul residents. Conclusions: It is necessary to review the universal health promotion project budget considering the degree of regional financial vulnerability from the viewpoint of health equity to narrow the health gap among regions.

• 한국정보통신학회논문지
• /
• 제8권2호
• /
• pp.440-448
• /
• 2004

본 논문에서는 II-Vl족의 ZnTe 화합물반도체 태양전지를 제작하기 위하여 투명전극(AZO) 및 Buffer layer(ZnO)의 특성과 태양전지의 효율에 가장 큰 영향을 미치는 광흡수층의 에너지밴드갭을 줄이는 연구를 하였다. ZnTe박막은 Zn(Zinc)과 Te(Tellurium)를 co-sputtering법을 이용하여 증착하였다. ZnTe 박막은 Zn과 Te의 RF power를 각각 50W, 30W로 하여 10mTorr의 Ae 분위기에서 20$0^{\circ}C$의 기판온도로 제작되었으며, 이때의 에너지밴드갭은 1.73eV였다. 이렇게 제작된 박막을 진공상태에서 $400^{\circ}C$의 온도로 10초간 열처리하여 1.67eV의 에너지밴드갭을 얻을 수 있었고, 이때의 Zn과 Te의 비율은 32%:68%였다. 최적의 조건에서 태양전지는 6.85% (Voc:0.69V, Jsc:21.408㎃/$cm^2$, Fill Factor (FF):0.46)의 효율을 얻을 수 있었다.

• Advances in pediatric surgery
• /
• 제7권1호
• /
• pp.1-6
• /
• 2001

The aims of this study were to evaluate the prognostic predictabilities of the risk classifications (Waterston, Montreal, and Spitz), preoperative treatment of pneumonia and the length of esophageal gap in esophageal atresia. Twenty-five cases of esophageal atresia were reviewed retrospectively. The data was analyzed with Likelihood ratio test for trend and Fisher's exact test. Survival rates were 100.0 % in group A and B, and 60.0 % in group C according to Waters ton classification (p=0.027). By Montreal classification, 95.7 % in group I and 50.0 % in group II (p=0.086). By Spitz classification, 95.5 % in group I and 66.7% in group II (p=0.159). The survival rate was 85.7 % in the patients with pneumonia preoperatively treated and 94.4% in the patients without pneumonia. The difference was not significant (p=0.490). Survival rate in the patients with long gap (${\geq}$3cm) was 50.0 % and 100.0 % in patients with short gap (<3cm) with significant difference (p=0.020). The Waterston classification could be modified into two groups because the prognosis of both group A and B were the same. Preoperative pneumonia does not seem to be a risk factor. The length of the esophageal gap showed prognostic value.