• 한국에너지공학회:학술대회논문집
• /
• 한국태양에너지학회, 한국에너지공학회 1993년도 춘계 공동학술발표회 초록집
• /
• pp.70-78
• /
• 1993

Heat pipes, applied to flat plate solar collectors, have a long and slender configuration with relatively low heat flux on the evaporator. Such a heat pipe has a tendency to build-up a liquid pool at the lower half of evaporator zone, and at this pool occurs such complicated phenomena of evaporation and fluid dynamics as superheat, sudden generation of bubble, its likely explosive growth process and flooding etc. In the present study, we tried to solve those problems by means of adjusting the two principle design parameters, liquid fill charge and wick length, using 4 heat pipes and 3 thermosyphons, with different values of parameter respectively. The corresponding results can be summarized as followings, - The thermal conductance of heat pipes was largely improved by el eliminating wick from adiabatic and condenser zone. - But on evaporator zone wick is inevitable to reduce behavior of the build -up of liquid pool , where arise diverse internal complex phenomena. - The liquid fill charge should have to be increased by 10∼20％ more than the quantity to saturate the wick.

• 한국안전학회지
• /
• 제16권3호
• /
• pp.1-6
• /
• 2001

The study is to investigate the influence on the fatigue crack growth behaviors for the welded configuration in pressure vessel stiffener. In order to perform this goal, the automatic welded specimens were prepared. The material is ASTM A516 grade 60 steel used in pressure vessel mainly. In skip welding of pad-on-plate, continuous fillet welding and PWHT specimen, fatigue crack is generally initiated at the starting and end old toe zone, and ruptured at the starting old toe zone. The fatigue life of pad-on-plate of the continuous fillet welding specimen is larger than that of pad-on-plate skip fillet welding specimen about 85% under low load, about 20% under high load and less than that of two-pad continuous fillet welding specimen about 85%. In da/dN-$\Delta$K curve under low load, skip fillet welding specimen of pad-on-plate showed retardation on the initial crack, and the fatigue crack growth rate at the low region of $\Delta$K greater specimen E($3.8 {\times} 10^{-6}mm/cycle$). And the fatigue life of welding specimen was smaller than that of PWHT specimen.

• 한국전기전자재료학회논문지
• /
• 제23권2호
• /
• pp.137-142
• /
• 2010

A plane wave expansion method (PWEM) was applied for photonic band structure calculation. We examined zero group velocity modes in photonic crystal. The zero group velocity modes were obtained at the second band along F-K direction. We expanded higher order Brillouin zone (BZ) to find the locations of zero group velocity modes and to investicate their properties. We found twelve locations, inside the first Brillouin zone, where the group velocities became zero. Also, we calculated band structure and group velocity in off-plane configuration.

• Steel and Composite Structures
• /
• 제35권4호
• /
• pp.579-598
• /
• 2020

Consideration of the panel zone (PZ) deformations in the analysis of steel moment frames (SMFs) has a substantial effect on structural response. One way to include the PZ effect on the structural response is Krawinkler's PZ model, which is one of the best and conventional models. However, modeling of Krawinkler's PZ model has its complexity, and finding an alternative procedure for PZ modeling is of interest. In this study, an efficient model is proposed to simplify Krawinkler's PZ model into an Adjusted Rigid-End Zone (AREZ). In this way, the rigid-end-zone dimensions of the beam and column elements are defined through an appropriate rigid-end-zone factor. The dimensions of this region depend on the PZ stiffness, beam(s) and columns' specifications, and connection joint configuration. Thus, to obtain a relationship for the AREZ model, which yields the dimensions of the rigid-end zone, the story drift of an SMF with Krawinkler's PZ model is equalized with the story drift of the same structure with the AREZ model. Then, the degree of accuracy of the resulting relationship is examined in several connections of generic SMFs. Also, in order to demonstrate the applicability of the proposed model in SMFs, several SMFs ranging from 3- to 30-story representing low- to high-rise buildings are examined through linear static and dynamic time history analysis. Furthermore, non-linear dynamic analyses of three SMFs conducted to validate the degree of accuracy of the proposed model in the non-linear analysis of SMFs. Analytical results show that there is considerable conformity between inter-story drift ratio (IDR) results of the SMFs with Krawinkler's PZ model and those of the centerline SMFs with AREZ.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2004년도 추계학술대회
• /
• pp.153-158
• /
• 2004

해양에 방류되는 오폐수의 흐름형태 즉 흔합특성을 제어하고 설계하기 위해 다양한 연구가 진행되고 있다. 최근 들어 선진국을 중심으로 바람직한 수질관리를 목표로 법적혼합역과 관련한 수질기준을 정하여 오염무의 방류로 인한 해양수질환경의 오염을 최소화하고자 하는 노력이 진행되고 있다. 본 논문에서는 이러한 근역 및 원역에서의 법적혼합역을 CORMIX 모델로 구현하고 법적혼합역의 필요성을 강조하며 이를 효율적으로 규제하기 위한 방안을 모색하고자 하였다. 이는 보다 개선된 방류수 모델링을 제안하고 나아가 효율적인 해양방류관 설계뿐 아니라 건전한 항만의 설계 및 개발에 기여할 것이다.

• Applied Microscopy
• /
• 제40권1호
• /
• pp.21-28
• /
• 2010

단층 및 복층의 그래핀에 대한 원자분해 투과전자현미경 영상 시뮬레이션 연구에서, 통상의 Boch-wave 방법에 의한 영상이론식들이 고 준위 Laue 영역의 역 격자 회절을 적절히 포함 했을 때 시뮬레이션에 잘 적용될 수 있음을 보여 주었다. 적절한 조건에서 복층 그래핀의 시뮬레이션 영상들은 육방정계의 대칭성 보다는 삼방정계의 대칭성을 보여 주었다. 이 결과는 복층 그래핀이 3차원 공간에서 [0001] 축 방향 회전에 대해 갖는 삼방정계의 격자 대칭성이 영상에 구현되는 것으로 이해될 수 있다. 단층 그래핀에 대해서는, 관측 위상영상이 삼방정계의 대칭성을 보여주는 현상들이 특히 주목되었다. 이 현상은 그래핀 표면에 전자 밀도의 재 배치에 의한 것으로 설명되었다. 그리고 그래핀의 전자 재 배치를 반영하는, 다만 2번째 Laue 준위 영역의 회절 빔까지만 포함하면 관측 영상과 일치하는 시뮬레이션 위상 영상이 얻어졌다.

• 한국임상수의학회지
• /
• 제40권3호
• /
• pp.203-208
• /
• 2023

A 13-year-old neutered male mixed-breed dog presented with generalized lymphadenopathy and erythematous cutaneous lesions in the ear pinnae. Fine-needle aspiration cytology of the lymph nodes revealed small to intermediate lymphocytes with a "hand mirror" configuration as the predominant cell type. Histopathological analysis of the lymph node showed an infiltrate of CD3-positive small lymphocytes compressing the follicles against the capsule owing to neoplastic cell expansion. Flow cytometric analysis revealed a homogeneous population of CD3+/CD4-/CD5+/CD8-/CD21+/CD34-/CD45- cells in both the peripheral blood and aspirated lymph nodes, which supports the diagnosis of T-zone lymphoma. Laboratory tests revealed lymphocytosis (14,144 cells/µL) in the peripheral blood. However, contrary to expectations, the bone marrow examination revealed no evidence of lymphocytic infiltration. T-zone lymphoma is an indolent lymphoma with a long survival period, and knowledge of its characteristics may affect disease staging and prognosis evaluation. Therefore, peripheral blood count as a sole screening tool for bone marrow metastasis should be used with caution.

• 반도체디스플레이기술학회지
• /
• 제6권1호
• /
• pp.17-22
• /
• 2007

Recent new packages such as MCP(Multi-Chip Package), QDP(Quadratic Die Package) and DDP(Dual Die Package) have stack type configuration. This kind of multi-layer package is thicker than single layer package. So there is need for the low height looping technology in wirebonder to make these packages thinner. There is stiff zone above ball in wirebonder wire which is called HAZ(Heat Affect Zone). When making low height loop (below $80\;{\mu}m$) with traditional forward loop, stiff wire in HAZ(Heat Affected Zone) above ball is bended and weakened. So the traditional forward looping method cannot be applied to low height loop. SSB(stand-off stitch) wire bonding method was applied to many packages which require very low loops. The drawback of SSB method is making frequent errors at making ball, neck damage above ball on lead and the weakness of ball bonding on lead. The alternative looping method is BNL(ball neckless) looping technology which is already applied to some package(DDP, QDP). The advantage of this method is faster in bonding process and making little errors in wire bonding compared with SSB method. This paper presents the result of BNL looping technology applied in assembly house and several issues related to low loop height consistence and BNL zone weakness.

• 대한방사선기술학회지:방사선기술과학
• /
• 제25권1호
• /
• pp.55-62
• /
• 2002

Aneurysm-mimicking findings were frequently visualized due to hemodynamical causes of dephasing effects around area of A-com artery during magnetic resonance angiography(MRA) and these kind of phenomena have not been clearly known yet. We investigated the hemodynamical patterns of dephasing effect around area of the A-com artery that might be a cause of false intracranial aneurysms on MRA. For experimental study, We used hand-made silicon phantoms of the asymmetric A-com artery as like a bifurcation configuration. In a closed circulatory system with UHDC computer driven cardiac pump system. MRA and fast digital subfraction angiography(DSA) involved the use of these phantoms. Flow patterns were evaluated with axial and coronal imaging of MRA(2D-TOF, 3D-TOF) and DSA of Phantoms constructed from an automated closed-type circulatory system filled with glycerol solution [circulation fluid(glycerol:water = 1:1.4)]. These findings were then compared with those obtained from computational fluid dynamic(CFD) for inter-experimental correlation study. Imaging findings of MRA, DSA and CFD on inflow zone according to the following: a) MRA demonstrated high signal intensity zone as inflow zone on silicon phantom; b) Patterns of DSA were well matched with MRA on trajectory of inflow zone; and c) CFD were well matched with MRA on the pattern of main flow. Imaging findings of MRA. DSA and CFD on turbulent flow zone according to the following: a) MRA demonstrated hyposignal intensity zone at shoulder and axillar zone of main inflow; b) DSA delineated prominent vortex flow at the same area. The hemodynamical causes of signal defect, which could Induce the false aneurysm on MRA, turned out to be dephasing effects at axilla area of bifurcation from turbulent flow as the results of MRA, DSA and CFD.

• 한국실내디자인학회논문집
• /
• 제36호
• /
• pp.93-101
• /
• 2003

The first object of this study is to clarify the newly demanded service to the visiter in the museum. And the second is to consider the spatial configuration on the layout of exhibition and the shape of exhibition room from the view points of behavior of appreciation and other methodology. The results of this study are as follows : The exhibition content and structure of Seoul Museum of History formed by a story-line according to the theme of an each zone fixed sequence in an each exhibition that we are achieved. But the layout of exhibition and the shape of exhibition consist on the other hand of the freedom selection. So the problem appeared In the difference of the exhibition content and the layout of exhibition to the behavior of appreciation. It can be said that the concept of exhibition space should be taken into account and the spatial configuration by the completed floor plan in order to satisfy the planning concepts.