• 한국지하수토양환경학회지:지하수토양환경
• /
• 제19권3호
• /
• pp.134-141
• /
• 2014

A testing inspection is one of the important in the industry, owing to determine the reliability and directivity of testing inspection results. Therefore, the quality assurance and quality control (QA/QC) work which performed by personnel not directly in the inventory compilation development, in testing inspection must be thoroughly considered. Some agencies for environmental test inspection, they sometimes misunderstood that the QA/QC was ended with proficiency testing performance and on-site assessment by a director. Thus, results were often calculated without QA/QC work by self manual when conducting test. The objective of this study was to improve reliability of testing and inspection agency through the QA/QC case study which basically performed to raising reliability of testing and inspection agency. In this study, it increased reliability of result by verifying calibration curve (IC, ICV, CCV), blank, accuracy (LCS, MS) and precision as QA/QC performance, while performing investigation of soil contamination in mining areas. This study suggests that reliability establishing method of test result and management method of analysis process, through the QA/QC instance of testing agency.

• Architectural research
• /
• 제9권1호
• /
• pp.47-52
• /
• 2007

The purpose of this research is to evaluate the feasibility of outsourcing test/inspection activity in construction work. This research conducted a questionnaire of interested parties as well as a survey by Analytic Hierarchy Process (AHP) with experts on quality control. For the evaluation by AHP, five criteria were adopted and a number of pair-wise comparisons were conducted through two stages. Finally, the weighting coefficient to approve the outsourcing was calculated at 0.606 and it therefore appeared more reasonable to permit rather than prohibit outsourcing. According to the AHP result, it was found that outsourcing would be necessary to enhance the objectivity and specialties of quality testing and inspection, even though somewhat undesirable in terms of enhancing a sense of responsibility and systemically conducting the testing and inspection.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 1997년도 춘계학술발표회 논문집
• /
• pp.139-144
• /
• 1997

• 품질경영학회지
• /
• 제8권2호
• /
• pp.15-22
• /
• 1980

This paper deals with the problem of determining a minimum cost sampling inspection plan for a single destructive testing by attribute. The cost for inspection lot is constructed by following three cost factors: (1) cost of inspection, (2) cost of accepted defective, (3) cost of rejected lot Using Hald's Bayesian approach in a single non-destructive testing, procedure's for finding the minimum cost single destructive sampling inspection plan by attribute are given. Assuming the uniform distribution as a prior-distribution and using numerical analysis by computer, a minimum cost single destructive sampling inspection plan by attribute for several lot sizes, unit cost, destructive testing cost, and salvage cost is given.

• 비파괴검사학회지
• /
• 제31권6호
• /
• pp.626-634
• /
• 2011

The investigation of concrete structure typically relies on visual inspection which is one of the basic inspection techniques. Image processing techniques play a crucial role in the growing field of automatic surface inspection technique. However, kinds of inspection equipment, environmental condition and detection algorithm have much influence on the reliability of inspection result. This paper proposes a verification method and testing procedure for the reliability of inspection results and surveys characteristics of image acquisition systems and crack inspection algorithms.

• 품질경영학회지
• /
• 제15권1호
• /
• pp.68-75
• /
• 1987

A rectifying inspection plan is considered for the case of destructive testing. Screening inspection for rejected lots is performed by some nondestructive testing which is prone to misclassification errors. Apparent defectives found in the screening process is replaced with apparent good items. The plan provides LTPD protection on each individual lot while the sum of the cost of testing and the cost due to producer's risk at process average quality is minimized. A brief discussion on average outgoing quality is also given.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권3호
• /
• pp.224-235
• /
• 2017

Purpose: Reliability is the most important factor to detect defects as wind turbines are deployed in large blades. The methods of detecting defects are various, such as non-destructive inspection and thermal imaging inspection. We propose the phased array ultrasonic testing method of non-destructive testing. Methods: We propose the active pressure mechanism for wind power blade. The phase array ultrasonic inspection method is used for fault detection inner blade surface. Controlled pressure of mechanism with respect to z-axis is important for guarantee the result of phase array ultrasonic inspection. The model based control and proposed mechanism are utilized for overall system stability and effectiveness of system. Result: The result of proposed pressure mechanism B is more stable than A. Convergence speed is also faster than A. Conclusion: We confirmed the performance of the proposed constant pressure mechanism through experiments. Non-destructive testing was applied to the specimen to confirm the reliability of detecting defects.

• 비파괴검사학회지
• /
• 제21권4호
• /
• pp.383-390
• /
• 2001

Long-range guided wave inspection is a new emerging technology for rapidly and globally inspecting a large area of a structure from a single test location. This paper describes a general overview of the guided wave properties and its application for long-range inspection of structures the principle and instrument system for a guided wave inspection technology called "magnetostrictive sensor (MsS)" that generates and detects guided waves electromagnetically in the material under testing, and examples of long-range guided wave inspection of structures that can be accomplished using the MsS.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.422-424
• /
• 2006

This paper suggests an automatic spot-inspection algorithm for LCD modules. Usually, LCD module testing is classified by two categories. One is for uniform pattern testing and the other is Non-uniform testing. The uniform pattern testing is well defined and also fully automated in the factory. However non-uniform pattern testing is not defined well yet, so non-uniform testing is conducted by human operators. In this paper a spot-pattern, which is one of non-uniform pattern, inspection algorithms are proposed. The performance of the proposed algorithm is tested by extensive simulations using artificial slot-patterns and real ones in the LCD modules.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 1997년도 추계총회 및 학술발표회 논문집
• /
• pp.89-92
• /
• 1997