• Korean Journal of Optics and Photonics
• /
• v.28 no.3
• /
• pp.108-115
• /
• 2017

We report the assembly procedure and performance evaluation of a visible and near-infrared spectrometer in the wavelength region of 400-900 nm, which is later to be combined with fore-optics (a telescope) to form a f/2.5 imaging spectrometer with a field of view of ${\pm}7.68^{\circ}$. The detector at the final image plane is a $640{\times}480$ charge-coupled device with a $24{\mu}m$ pixel size. The spectrometer is in an Offner relay configuration consisting of two concentric, spherical mirrors, the secondary of which is replaced by a convex grating mirror. A double-pass test method with an interferometer is often applied in the assembly process of precision optics, but was excluded from our study due to a large residual wavefront error (WFE) in optical design of 210 nm ($0.35{\lambda}$ at 600 nm) root-mean-square (RMS). This results in a single-path test method with a Shack-Hartmann sensor. The final assembly was tested to have a RMS WFE increase of less than 90 nm over the entire field of view, a keystone of 0.08 pixels, a smile of 1.13 pixels and a spectral resolution of 4.32 nm. During the procedure, we confirmed the validity of using a Shack-Hartmann wavefront sensor to monitor alignment in the assembly of an Offner-like spectrometer.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.3
• /
• pp.33-38
• /
• 2021

Recently, rollable and foldable displays are attracting great attention in the flexible display market due to their excellent form factor. To predict and prevent the mechanical failure of the display panels, it is essential to accurately understand the mechanical properties of brittle SiN_x thin films, which have been used as an insulating film in flexible displays. In this study, tensile properties of the ~130 nm- and ~320 nm-thick SiN_x thin films were successfully measured by coating a ~190 nm-thick organic nano-support-layer (PMMA, PS, P3HT) on the fragile SiN_x thin films and stretching the films as a bilayer state. Young's modulus values of the ~130 nm and ~320 nm SiN_x thin films fabricated through the controlled chamber pressure and deposition power (A: 1250 mTorr, 450 W/B: 1000 mTorr, 600 W/C: 750 mTorr, 700 W) were calculated as A: 76.6±3.5, B: 85.8±4.6, C: 117.4±6.5 GPa and A: 100.1±12.9, B: 117.9±9.7, C: 159.6 GPa, respectively. As a result, Young's modulus of ~320 nm SiN_x thin films fabricated through the same deposition condition increased compared to the ~130 nm SiN_x thin films. The tensile testing method using the organic nano-support-layer was effective in the precise measurement of the mechanical properties of the brittle thin films. The method developed in this study can contribute to the robust design of the rollable and foldable displays by enabling quantitative measurement of mechanical properties of fragile thin films for flexible displays.

• Journal of Korean Society of Disaster and Security
• /
• v.12 no.2
• /
• pp.73-82
• /
• 2019

Recently, as the occurrence frequency of sudden floods due to climate change increased, the flood damage on riverside social infrastructures was extended so that there has been a threat of overflow. Therefore, a rapid prediction of potential flooding in riverside social infrastructure is necessary for administrators. However, most current flood forecasting models including hydraulic model have limitations which are the high accuracy of numerical results but longer simulation time. To alleviate such limitation, data driven models using artificial neural network have been widely used. However, there is a limitation that the existing models can not consider the time-series parameters. In this study the water surface elevation of the Hangang River bridge was predicted using the NARX model considering the time-series parameter. And the results of the ANN and RNN models are compared with the NARX model to determine the suitability of NARX model. Using the 10-year hydrological data from 2009 to 2018, 70% of the hydrological data were used for learning and 15% was used for testing and evaluation respectively. As a result of predicting the water surface elevation after 3 hours from the Hangang River bridge in 2018, the ANN, RNN and NARX models for RMSE were 0.20 m, 0.11 m, and 0.09 m, respectively, and 0.12 m, 0.06 m, and 0.05 m for MAE, and 1.56 m, 0.55 m and 0.10 m for peak errors respectively. By analyzing the error of the prediction results considering the time-series parameters, the NARX model is most suitable for predicting water surface elevation. This is because the NARX model can learn the trend of the time series data and also can derive the accurate prediction value even in the high water surface elevation prediction by using the hyperbolic tangent and Rectified Linear Unit function as an activation function. However, the NARX model has a limit to generate a vanishing gradient as the sequence length becomes longer. In the future, the accuracy of the water surface elevation prediction will be examined by using the LSTM model.

• The Journal of Korean Academy of Prosthodontics
• /
• v.57 no.2
• /
• pp.127-133
• /
• 2019

Purpose: The purpose of present study was to investigate fracture strength and mode of failure of endodontically treated teeth restored with metal cast post-core system, prefabricated fiber post system, and newly introduced polyetherketoneketone (PEKK) post-core system. Materials and methods: A total of 21 mandibular premolar were randomly grouped into 3 groups of 7 each according to the post material. Group A was for metal cast post core; Group B for prefabricated glass fiber post and resin core; and Group C for milled PEKK post cores. All specimens were restored with metal crown. The fracture strength of each specimen was measured by applying a static load of 135-degree to the tooth at 2 mm/min crosshead speed using a universal testing machine. After the fracture strength measurement, the mode of failure was observed. The results were analyzed using Kruscal-Wallis test and post hoc Mann-Whitney U test at confidence interval ${\alpha}=.05$. Results: Fracture resistance of PEKK post core was lower than those of cast metal post and fiber reinforced post with composite resin core. In the aspect of fracture mode most of the root fracture occurred in the metal post core, whereas the post detachment occurred mainly in the fiber reinforced post. In the case of PEKK post core, teeth and post were fractured together. Conclusion: It is necessary to select appropriate materials of post for extensively damaged teeth restoration and clinical application of the PEKK post seems to require more research on improvement of strength.

• Korean Journal of Ecology and Environment
• /
• v.56 no.1
• /
• pp.45-56
• /
• 2023

In stream ecosystem assessment, RIVPACS, which makes a simple but clear evaluation based on macroinvertebrate community, is widely used. In this study, a preliminary study was conducted to develop a RIVPACS-type model suitable for Korean streams nationwide. Reference streams were classified into two types(upstream and downstream), and a prediction model for macroinvertebrates was developed based on each family. A model for upstream was divided into 7 (train): 3 (test), and that for downstream was made using a leave-one-out method. Variables for the models were selected by non-metric multidimensional scaling, and seven variables were chosen, including elevation, slope, annual average temperature, stream width, forest ratio in land use, riffle ratio in hydrological characteristics, and boulder ratio in substrate composition. Stream order classified 3,224 sites as upstream and downstream, and community compositions of sites were predicted. The prediction was conducted for 30 macroinvertebrate families. Expected (E) and observed fauna (O) were compared using an ASPT biotic index, which is computed by dividing the BMWPK score into the number of families in a community. EQR values (i.e. O/E) for ASPT were used to assess stream condition. Lastly, we compared EQR to BMI, an index that is commonly used in the assessment. In the results, the average observed ASPT was 4.82 (±2.04 SD) and the expected one was 6.30 (±0.79 SD), and the expected ASPT was higher than the observed one. In the comparison between EQR and BMI index, EQR generally showed a higher value than the BMI index.

• Analytical Science and Technology
• /
• v.20 no.5
• /
• pp.434-441
• /
• 2007

The aim of this paper is to investigate composition of fatty acids in sweat on purpose of latent fingerprint detectant developing and crime evidence searching. Fingerprint from 5 male donors (aged 29-50 years) were collected. We identified fatty acid components on sweat using methylester mixture (37species) as standard fatty acid and analyzed them by GC-FID. As donor was aged, the level of total fat was found to decrease markedly (aged 20-30 years: 56.4-72.0 %, aged 50 years : 32.4-45.4 %). We identifided 28 species fatty acid, primarilly C16:0(palmitic acid), C16:1 (palmitoleic acid), C18:1n9c(oleic acid), C18:0 (stearic acid), C14:0 (tetradecanoic acid) and all sweats were found to contain C12:0 (lauric acid), C15:0 (pentadecanoic acid), C18:2n6c (linoleic acid), C18:2n6t (linolelaidic acid), C20:0 (arachidic acid), C24:0/C20:5n3 (lignoceric acid/eicosapentaenoic acid), but with differing frequencies and at varying levels. C14:1 (myristoleic acid), C15:1 (pentadecenoic acid), C21:0 (heneicosanoic acid), C22:1n9 (erucic acid) were often observed in sample. Ratio of saturated and unsaturated fatty acid was from 0.94:1 to 2.6:1. And decrease of total fatty acids components caused by loss of saturated fatty acid and monounsaturated fatty acid. In case of sweat amino acids, we detected serine ($0-31.9{\mu}L/mL$), threonine ($0-26.2{\mu}L/mL$), glycine ($0-18.9{\mu}L/mL$) and 20-30 years old, highly protein intake ratio individuals increased (10 times) than 50 years old. We observed greatly individual characterization of amino acid compounds in sweat.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.902-909
• /
• 2023

This study evaluated the performance test of a small-sized LTE-Maritime(LTE-M) transceiver that was developed and promoted to expand the use of intelligent maritime traf ic information services led by the Ministry of Oceans and Fisheries with the aim of supporting the prevention of maritime accidents. Accoriding to statistics, approximately 30% of all marine accidents in Korean water occur with ships weighing less than 3 tons. Therefore, the blind spots of maritime safety must be supplemented through the development of small-sized transceivers. The small transceiver may be used in fishing boats that are active near coastal waters and in water leisure equipment near the coastline. Therefore, verifying whether sufficient performance and stable communication quality are provided is necessary, considering the environment of their real usage. In this study, we reviewed the communication quality goals of the LTE-M network and the performance requirements of small-sized transceivers suggested by the Ministry of Oceans and Fisheries, and proposed a test plan to appropriately evaluate the performance of small-sized transceivers. The validity of the proposed test method was verified for six real-sea areas with a high frequency of marine accidents. Consequently, the downlink and uplink transmission speeds of the small-sized LTE-M transceiver showed performances of 9 Mbps or more and 3 Mbps or more, respectively. In addition, using the coverage analysis system, coverage of more than 95% and 100% were confirmed in the intensive management zone (0-30 km) and interesting zone (30-50 km), respectively. The performance evaluation method and test results proposed in this paper are expected to be used as reference materials for verifying the performance of transceivers, contributing to the spread of government-promoted e-navigation services and small-sized transceivers.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.6
• /
• pp.120-129
• /
• 2023

To evaluate the vertical loads on railway bridges, conventional load tests are typically conducted. However, these tests often entail significant costs and procedural challenges. Railway conditions involve nearly identical load profiles due to standardized rail systems, which may appear straightforward in terms of load conditions. Nevertheless, this study aims to validate load tests conducted under operational train conditions by comparing the results with those obtained from conventional load tests. Additionally, static and dynamic structural behaviors are extracted from the measurement data for evaluation. To ensure the reliability of load testing, this research demonstrates feasibility through comparisons of existing measurement data with sensor attachment locations, train speeds, responses between different rail lines, tendency analysis, selection of impact coefficients, and analysis of natural frequencies. This study applies to the Dongho Railway Bridge and verifies the applicability of the proposed method. Ten operational trains and 44 sensors were deployed on the bridge to measure deformations and deflections during load test intervals, which were then compared with theoretical values. The analysis results indicate good symmetry and overlap of loads, as well as a favorable comparison between static and dynamic load test results. The maximum measured impact coefficient (0.092) was found to be lower than the theoretical impact coefficient (0.327), and the impact influence from live loads was deemed acceptable. The measured natural frequencies approximated the theoretical values, with an average of 2.393Hz compared to the calculated value of 2.415Hz. Based on these results, this paper demonstrates that for evaluating vertical loads, it is possible to measure deformations and deflections of truss railway bridges through load tests under operational train conditions without traffic control, enabling the calculation of response factors for stress adjustments.

• Journal of the Korean Applied Science and Technology
• /
• v.41 no.2
• /
• pp.484-497
• /
• 2024

Neonicotinoid pesticides, widely used worldwide as potent insecticides, have been found to have detrimental effects on the environment and living organisms due to their persistent residues. This study aimed to investigate the neonicotinoid pesticides, imidacloprid, and clothianidin, focusing on their impact on honey bee toxicity and foliar residue levels. Alfalfa was selected as control crop while bell peppers, and cucumbers were chosen as representative application crops, respectively. The investigation involved comparing the toxicity and foliar residue levels resulting from soil and foliar treatments, with a focus on identifying potential shortcomings in conventional foliar residue toxicity testing methods. Imidacloprid and clothianidin were applied to crops or soil at recommended rates and through irrigation. The honey bee mortality rate (RT₂₅) over time was determined, and pesticide residues on leaves were quantified using High-Performance Liquid Chromatography (HPLC). The results revealed that foliar treatment with imidacloprid on alfalfa resulted in an RT₂₅ of less than 1 day, with residues ranging from 1.07 to 19.27 mg/kg. In contrast, application on bell peppers showed RT₂₅ within 9 days, with residues ranging from 1.00 to 45.10 mg/kg. Clothianidin foliar treatment displayed RT₂₅ within 10 days on alfalfa, with residues between 0.61 and 2.57 mg/kg. On bell peppers, RT₂₅ was within 28 days, with residues ranging from 0.13 to 2.85 mg/kg. Soil treatment with imidacloprid and clothianidin in alfalfa exhibited minimal impact on honey bees and residues of 0.05 to 0.37 mg/kg. However, in applied crops, imidacloprid showed RT₂₅ within 28 days and residues ranging from 4.47 to 130.43 mg/kg, while clothianidin exhibited RT₂₅ within 35 days and residues between 5.96 and 42.32 mg/kg. In conclusion, when comparing honey bee toxicity and foliar residues among crops, application crops had a more significant impact on honey bee mortality and higher residue levels compared to control crops. Moreover, soil treatment for application crops resulted in higher RT₂₅ and residue levels compared to foliar treatment. Therefore, to ensure pesticide safety and environmental sustainability, diverse research approaches considering different crops and application methods are necessary for the safety assessment of imidacloprid and clothianidin.

• Economic and Environmental Geology
• /
• v.57 no.2
• /
• pp.205-217
• /
• 2024

This study evaluated the physical characteristics and quality of volcanic rocks distributed in the Jeju Island-Ulleung Island area as aggregate resources. The main rocks in the Jeju Island area include conglomerate, volcanic rock, and volcanic rock. Conglomerate is composed of yellow-red or gray heterogeneous sedimentary rock, conglomerate, and encapsulated conglomerate in a state between lavas. Volcanic rocks are classified according to their chemical composition into basalt, trachybasalt, basaltic trachytic andesite, trachytic andesite, and trachyte. By stratigraphy, from bottom to top, Seogwipo Formation, trachyte andesite, trachybasalt (I), basalt (I), trachybasalt (II), basalt (II), trachybasalt (III, IV), trachyte, trachybasalt (V, VI), basalt (III), and trachybasalt (VII, VIII). The bedrock of the Ulleung Island is composed of basalt, trachyte, trachytic basalt, and trachytic andesite, and some phonolite and tuffaceous clastic volcanic sedimentary rock. Aggregate quality evaluation factors of these rocks included soundness, resistance to abrasion, absorption rate, absolute dry density and alkali aggregate reactivity. Most volcanic rock quality results in the study area were found to satisfy aggregate quality standards, and differences in physical properties and quality were observed depending on the area. Resistance to abrasion and absolute dry density have similar distribution ranges, but Ulleung Island showed better soundness and Jeju Island showed better absorption rate. Overall, Jeju Island showed better quality as aggregate. In addition, the alkaline aggregate reactivity test results showed that harmless aggregates existed in both area, but Ulleungdo volcanic rock was found to be more advantageous than Jeju Island volcanic rock. Aggregate quality testing is typically performed simply for each gravel, but even similar rocks can vary depending on their geological origin and mineral composition. Therefore, when evaluating and analyzing aggregate resources, it will be possible to use them more efficiently if the petrological-mineralological research is performed together.