• Tunnel and Underground Space
• /
• v.8 no.4
• /
• pp.332-341
• /
• 1998

Conventional polishing of stone panel edges has been done by hand. While this has changed somewhat with the advent of automatic machines, it is still very much a hand finishing technology. For the development of edge shape milling tool, the primary test on characteristics of edge shape milling tool was carried out. This paper presents the results of tests focused upon the milling capability that was varied by the variables of operation parameters. Author tried to confirm the effect of six operation parameters of equipment such as rotation speed, advance speed, applied load, water flow rate and rotational direction. The result from test was described in term of shape milling capability that was defined as cutting volume of rock by unit weight of tool wear. The variance of the results could indicate the optimum level of each operating parameters. The test was also carried out to determine the abrasion resistance varied according to the abrasive flow rate. The abrasion resistance was increased with the abrasive flow rate, but over some rate it was not changed.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.627-634
• /
• 2014

Machine tool vibration is well known for reducing machining accuracy. Because vibration response of a linear structure generally depends on its transfer function if the magnitude of excitation were kept constant, this study introduces a RET(Random Excitation Test) based on FRF method to evaluate stiffness of a prototype HDMTL(Heavy-Duty Multi-Tasking Lathe) for large crankshaft of marine engine. Firstly, two force loops of the lathe and corresponding structural loops were identified:1) workpiece - spindle - head stock - main bed, 2) workpiece - tool post - carriage bed. Secondly, compliances of each structural loop were measured respectively using RET with a hydraulic exciter and then converted into stiffness. Finally, the measured stiffness was compared with that obtained previously by FEM analysis. As the result, both measured and computed stiffness were closely in agreement with each other. And the prototype HDMTL has evidently sufficient rigidity above ordinary heavy-duty lathes.

• The Korean Journal of Health Service Management
• /
• v.7 no.2
• /
• pp.101-111
• /
• 2013

To develop the Korean-Version-Improvement program for ordinary people, we investigate how Korean-High-Intelligent people use their cognitive function, intellectual capacity and Intelligent Quotient test. Using Mensa iq test, we classify intelligent examination tool into various components; visual, geometrical component and cognitive interpretation component. Also we organized each component, got database of intelligent subjects sample, classified itemized availability. Based on these things, we prove efficiency of intelligent examination tool. We found out that high intelligent people showed high Intelligent Index using visual cognitive stimulation with cognitive function when subjects were exposed to certain situation; solving the problem. This intelligent examination tool is low price and safe and easily carrying out with personal computer. If we develop intelligence quotient examination customized with mental retardation populations, a variety of subjects will improve their cognition with efficiency and inexpensively.

• Journal of the Korean Society for Railway
• /
• v.3 no.3
• /
• pp.147-153
• /
• 2000

The train control and monitoring system (TCMS) is an on board computer system in railway vehicles performing the control, supervisory and diagnostic functions of the complete train system. This system replaces a lot of hard-wired relays and minimizes the necessary vehicle wiring thus increasing the reliability of the train. It is also one of more important equipment on vehicle to implement much higher safety and reliability train system. We studied a software design technique of TCMS using a CASE tool that is a kind of safety critical software engineering tool (SCADE). This tool has mainly four functions such as the graphical editor, the document maker, tile automatically code generator, and the test simulator. The several functions of TCMS are implemented in this software easily programmed using a functional block diagram and a graphic programming language. We applied to automatically generated TCMS modules on the SCADE each functional block for the Standard type EMU in Korea. We performed the combination test using TCMS simulator and the running test in Seoul subway 7 Line. We proved that this technique is more useful for the software design of TCMS in urban transit

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.75-78
• /
• 2000

There are several effective factors to influence die life in the warm forging process. For instance process design die design and die materials etc This study presented heat treatment method which could improve toughness and wear resistance simultaneously in high temperature to apply high speed tool steels like SKH51 to die material for warm forging process. To verify the feasibility of application of heat treatment method mentioned above wear test was performed under the condition of constant time in 40$0^{\circ}C$ Wear coefficient was examined to search a relation between wear amount and time for each material and heat treatment method in 30, 60, and 130 minutes. To quantify the toughness-behavior between room and high temperature impact test was performed and heat fatigue test also fulfilled to compare with the resistance of heat check in room, 200, 400, and $600^{\circ}C$ temperature. On the basis of experimental results mentioned above high speed tool steel was applied to verify appropriateness of newly proposed heat treatment method for die of rotor pole used in automobile alternator. As a result die life of high speed tool steel applied newly proposed heat treatment is longer than that of STD61.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.2
• /
• pp.38-44
• /
• 2021

To cater to the transition from single-color to multicolor/multi-material printing, this paper proposes a cartridge-replacing type multi-nozzle Fused Depositon Modeling(FDM) three-dimensional (3D) printer. In the test printing run, tool change failure/wobble/layer shift occurred. It was confirmed that improper support was the cause of this tool change failure. As a solution, spline and electromagnetic cartridges were designed. Wobble was caused by machine vibration and the motor stepping out. To minimize wobble, an additional Z-axis was installed, and the four-point bed leveling method was used instead of the three-point bed leveling method. The occurrence of layer shift was ascribed to the eccentricity of the Z-axis lead screw. Therefore, slit coupler was replaced with an Oldham type. In addition to the mechanical supplementation, the control environment was integrated to prevent accidents and signal errors due to wire connections. Before the final test printing run, a rectifier circuit was added to the motor to secure precise control stability. The final test printing run confirmed that the wobble/layer shift phenomenon was minimized, and the maximum error between layers was reduced to 0.05.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.84-87
• /
• 2008

ATTOL is a software unit testing tool produced by the ATTOL Testware SA in France. It automates the entire software unit testing process: test plan template and test program generation, test program execution, test result analysis and test report generation. ATTOL is suited for the development of embedded software as it allows programmers to operate in native and cross development environments. Particularly, it is used for the development of the flight software which is embedded in the Communication Ocean Meteorological Satellite (COMS). As the flight software is mission-critical, it requires the strict software quality and high testing constraints. The flight software of COMS is verified by ATTOL in native and cross platforms. In 2002, ATTOL was taken over by the IDM Rational Software and has been supplied with the name of Test RealTime (TestRT). The test process of TestRT becomes different from that of ATTOL as TestRT provides the new functionalities that were absent from ATTOL. TestRT provides the new features in the test script language, as well. In this paper, we compare the test process of ATTOL to TestRT With an example of COMS and explain what has been changed in the test script language.

• MALSORI
• /
• no.33_34
• /
• pp.91-98
• /
• 1997

Auditory discrimination which represents a very basic and important perceptual skill in children is a necessary condition for effective learning. It is necessary, therefore, to devise a standardized test tool for a reliable assessment of the auditory discrimination ability of children. The Korean Auditory Discrimination Test(KADT) is a tentative test tool that the authors have devised to meet such demand, i.e., to test the auditory discrimination ability of Korean children, both normal and hearing- and speech-impaired, between the ages of 4 and 8. The KADT consists of 40 pairs of words arranged in a systematic manner, of which thirty are 'minimal pairs' of words and the rest homophonous synonyms. The 30 minimal pairs are composed in such a way that major phonological contrasts involving consonants and vowels at initial, medial and final positions are duly represented. The test score will be determined by the number of right responses made by the children. Further attempts will be made to refine and improve KADT in future.

• Journal of Preventive Medicine and Public Health
• /
• v.26 no.4 s.44
• /
• pp.650-660
• /
• 1993

This study aims to describe the causes of medically unnecessary hospital stay at a teaching tertiary hospital, using modified version of Delay Tool in which the causes of delay are divided into slx major categories : delay related to test scheduling, test results, surgery, medical staff, patient/family, and administration. For the analysis of hospital stay, 6,479 inpatient-days were reviewed in two medical and four surgical departments for one month. Initially inappropriate hospital stays were identified using Appropriateness Evaluation Protocol (AEP), and causes of delay listed in Delay Tool were assigned to each of them. In both medical and surgical services, the most important cause of delay was related to medical staffs, ranging from 3.6% to 51.6% of total inpatient days. Next important category was delay related to test scheduling in medical services ($4.7{\sim}9.2%$), and delay related to surgery in surgical services ($7.3{\sim}15.0%$). Among subcategories of delay related to medical staffs, delay due to conservative care was the most important cause of inappropriate hospital stay ($2.9{\sim}6.4%$). Each clinical departments had different distribution among delay categories, which could not be fully justified by their clinical charateristics. The Delay Tool would be helpful in exploring factors related to the inefficient use of hospital beds. As a measurement tool of inappropriate hospital stay, however, the Delay Tool should be refined in the definitions of categories and its contents.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.5B
• /
• pp.247-252
• /
• 2005

The testing tools implemented up to now for the LDAP(Light-weight Directory Access Protocol) interoperability tests are not easy to modify or add new test items since their source codes are not open. The object-oriented approach, therefore, is required to implement such a testing tool which can be easily modified or add new test items. Thus we designed the architecture for the testing tool applying the object-oriented approach. Java language, appropriate for the object-oriented approach, was used to implement the testing tool. The newly implemented testing tool can modify partly to adapt to the already stored data in the test suite information even during tests. Five LDAP servers can be tested simultaneously with the same configuration setup. Actual testing for the two LDAP servers validates the usefulness of the designed architecture with the proper working of the implemented testing tool according to the architecture.