• 전기학회논문지
• /
• 제61권8호
• /
• pp.1083-1090
• /
• 2012

In this paper, we present the section load estimation program of distribution system for smart distribution management system. The proposed program is composed with three parts. One is the consistency check part for switch measurements which consist a section. The consistency check is divided into the current and angle test. For the current test, we examine the input and output power flow for the switch group. For the angle test, the result of power flow calculation at previous step is used. Another is the voltage estimation part for the measured switches. We use the weighted least square (WLS) method for the voltage estimation. The third is the part of final section load calculation. The database structure for accomplishing the developed estimation program is also proposed. To verify the accuracy of the experimental results, case studies are performed using a actual data of Jeju island. The developed program can be effectively applied to the distribution operation systems.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.128-131
• /
• 2004

This paper is to investigate the mock up test results of mass concrete for transfer girder using setting time difference with super retarding agent(SRA) to reduce hydration heat. According to test results, the temperature history of plain concrete without placing lift had a steep rising curvature, and plain concrete had a big temperature difference between surface and middle section of mass concrete, which may result in occurrence of temperature crack. However, considering placing method B, because setting time of middle section concrete was retarded with an increase in SRA contents, higher hydration heat temperature was observed at surface section concrete compared with that at middle section concrete at early age, which can lower the possibility of hydration heat crack. In case of placing method C, although peak temperature of hydration heat was much lower, at early age, high crack occurrence possibility of the hydration heat attributable to the big temperature difference between middle section and bottom section of concrete was expected at bottom section concrete. Therefore, the structure above the ground like transfer girder is not applicable to consider the placing method C.

• 대한간호학회지
• /
• 제34권2호
• /
• pp.324-332
• /
• 2004

Purpose: The purpose of this study was to explain differences of cesarean section rates according to San- Yin-Jiao(SP6) acupressure for women in labor. Method: A noneqivalent control group pre test - post test design was used to explain differences of cesarean section rates according to SP6 acupressure. The participants were 209 women who were assigned to one of three groups SP6 acupressure(n=86), SP6 touch(n=47), and control group(n=76). For 30 minutes, the SP6 acupressure group received SP6 acupressure, and the SP6 touch group received SP6 touch for the duration of each uterine contraction. The Control group was encouraged to deep breath and relax for the duration of each uterine contraction for 30 minutes. Result: The rates of cesarean section were 12.8%, 29.8%, and 22.4% for the SP6 acupressure group, SP6 touch group, and control group respectively. There was a significant difference among groups (p=0.049). Cesarean section rateswere significantly different between the SP6 acupressure and non-SP6 acupressure group(p=0.035). Conclusion: This finding shows that 30 minutes of SP6 acupressure was effective in decreasing the cesarean section rate. Therefore, SP6 acupressure during labor could be applied as an effective nursing intervention.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.977-980
• /
• 2011

본 논문에서는 항공우주연구원에서 개발중인 1단 저압 축류압축기 성능시험리그의 개발에 대한 내용을 소개하고자 한다. 성능시험리그는 유동 입구부, 동익단, 정익단, 축, 리그 하우징, 베어링 하우징 및 유동 출구부로 구성되어 있다. 로터와 회전축을 단순화하여 회전동역학 해석 결과를 바탕으로 회전축을 설계하고 입 출구 유로의 유동해석을 통해서 시험리그 형상설계를 최적화하였다.

• 한국전산유체공학회지
• /
• 제1권1호
• /
• pp.134-141
• /
• 1996

Wall interference is one of the major obstacles to increase the model size and data accuracy. There have been many treatments for wall interference including interference correction and adaptive wall test section. Recently, two-flexible-walled adaptive wall test section is concluded adequate for three-dimensional test. But proper location of target line and pressure holes are critical to its success. In this study, a new adaptive algorithm which dispenses target line and dependency of pressure hole distribution is suggested. The wind tunnel and free air tests are simulated by the numerical computation of Euler equations. The optimum wall shape is achieved by two variable optimization which is composed of two base streamlines. The wall interference is reduced well in the optimized result which is not sensitive to the base streamlines.

• 한국안전학회지
• /
• 제19권3호
• /
• pp.78-83
• /
• 2004

The channel-type lining board that partial welded on many partition frames is used to normal servicing lining board type. On this study is to investigate existing channel-type lining board's capacity by using the static loading test. From this study, to develop new-type lining board which reflect well cross section area and sectional modulus of existing channel-type lining board. Six types FEM model are adopted. The accumulated test results of stress conditions and deflections by section shapes will be used to analyzed the relation between the capacity and the section shape. With the comparing the results of static loading test and FEM analysis.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.635-642
• /
• 1997

This research focused on the development of concrete overlay and test, which was conducted at 88 Highway 105k, 2 lanes of 290 m. The field application test consists of 6 cm and 10 cm bonded concrete overlay and 25 cm unbonded concrete overlay, using the slag cement for opening lanes for traffic early. The overlay were placed in a day. The whole period of traffic closing wes 8 day and it was reopened to traffic after concrete overlay has cured for 3 day. 5 cracks were founded when the field test section was investigated after 1 month, but all these may not make significant problems to overlay because these initiated and growed at the same line of repair section. The rideability and skid resistance become much better like in the new pavement after overlay. The structural capacity against deflection was much. which were verified by FWD(Falling Weight Deflectometer). The field test section is being used in a good condition and the results of field application and pavement performance analysis are encouraging. This rehabilitation methods may be adopted in Korea after a more field performance verifications.

• 한국항공운항학회지
• /
• 제13권4호
• /
• pp.92-99
• /
• 2005

A closed-circuit type wind tunnel is designed, which has a test section with the dimensions $1.2(W){\times}1.2(H){\times}3.4(L)$. A subsonic wind tunnel is designed to improves educational circumstances and promote ground tests. It is constituted of an exchangeable test section, first and second diffusers, a fan, a settling chamber, a contraction, and 4 corners. The maximum velocity in the test section is 70m/s and the contraction ratio is 6.25:1. Input power in the wind tunnel is about 96.1 kw (128.8 hp) and its energy ratio is 3.89. It has the dimension of about $7.4(W){\times}3.6(H){\times}21.7m(L)$. The wind tunnel designed in this investigation will be an effective educational and investigational equipment.

• Nuclear Engineering and Technology
• /
• 제10권2호
• /
• pp.79-86
• /
• 1978

본 연구의 목적은 수직 연료봉 집합체에서 물-공기 2상 유동일 경우 공기분포현상에 관한 실험적 데이타를 얻는데 있다. test-section은 6각형, 61개의 연료봉 집합체로 구성되며, 각 연료봉은 helical spacers로 감겨져 있고, 사용되는 유체는 공기와 물이다. 실험은 크게 2부분으로 나누어서 물의 유량을 일정하게 하고 공기의 유량을 증가시킬 경우와 물자 공기의 유량을 동시에 증가시킬 경우의 공기분포현상에 관해 실시하였다. 공기는 4구멍을 통해 각각 주입시켰다. 보이드율의 측정은 전기적 Void-needle 방법을 적용하였으며 그 결과는 도표를 통해 보여주고 있다. 이 실험의 결과로써 물의 유랑을 증가시킬 수록 공기분포는 균일하게 되며, 공기 공급 위치는 공기분포에 큰 영향을 미치고 있음이 입증되었다.

• 한국항행학회논문지
• /
• 제18권5호
• /
• pp.445-454
• /
• 2014

본 논문에서는 다목적 디스플레이의 인증 과정에서 수행 했던 시험 중 간접 낙뢰의 영향성을 검증하기 위한 RTCA DO-160 F, Section 22 시험 수행을 위한 대책 설계 내용 및 시험 과정을 소개한다. 낙뢰 유도 전압은 항공기 전기 전자장비의 기능 장애또는 손상을 가져다 주는 데 이것을 낙뢰의 간접영향이라 한다. 이러한 항공기의 낙뢰 간접영향으로부터 항공전자장비를 보호하기 위해서는 항공기에 대한 낙뢰의 영향과 항공기 내부 시스템을 분석하고 해당 부품에 대한 위협 내용에 대한 보호 설계가 필요하다. 본 논문에서는 이와 같은 항공기용 다목적 디스플레이의 낙뢰에 대한 보호를 위하여 대책 수준을 결정을 위한 RTCA DO-160 F, Section 22 category 선정 방법 및 선정된 레벨에 따른 부품 선정 방법 등을 소개한다. 또한 선정된 부품의 설계 유효성을 확인하기 위하여 실제 시험 과정을 소개한다. 이와 같은 각 단계별 과정 소개를 통하여 향후 개발 예정인 항공전자 장비에 대한 낙뢰 대책 설계의 좋은 사례가 될 것으로 예상한다.