• 한국항공우주학회지
• /
• 제32권6호
• /
• pp.117-125
• /
• 2004

본 논문에서는 기체 구조건전성 기준서 (MIL-HDBK-1530B) 및 기체 구조건전성 프로그램 (ASIP)에 의거하여 고등 훈련기 (T-50)의 구조건전성평가와 양산 결정자료 획득을 위한 전기체 내구성시험 기법 개발에 대하여 기술하였다. 전기체 부유식 시험조립 기법, 시험하중 최적화 모사 기법, 시험부가 장치 설계 시법, 시험조립 기법, 및 설치 기법, 시험안전장치 설계 및 운용 기법 및 전기체 내구성시험 수행 결과를 수록하였다. 1배 수명 전기체 내구성시험을 성공적으로 수행함으로써 시험기법의 타당성을 입증하였다.

• 한국기계가공학회지
• /
• 제20권1호
• /
• pp.125-131
• /
• 2021

For the vibration reliability tests, the jigs for mounting the test specimen on a vibration reliability tester are required. The dynamic stabilities of the jigs should be verified before the tests for obtaining the accurate reliability of the test specimen. This paper proposes an analytical technology for ensuring the dynamic structural stability for the test setup including the jig. The technology includes the mode analyses for checking resonance, the harmonic analyses for evaluating the dynamic structural stability of test setup including the jig, and the fatigue analyses for obtaining the durable reliability time with calculating the life cycles at the area of weakness. The cause investigation of the damaged jig during vibration reliability test of a rubber hose and the design of new revised jig are performed by using the technology. The vibration reliability test for the rubber hose with the new revised jig by analysis results is successfully conducted without any problem. Therefore the jig's design technology proposed in this paper may be useful for other items as well.

• 한국군사과학기술학회지
• /
• 제10권3호
• /
• pp.154-160
• /
• 2007

A direction finding system test-bed(DFSTB) at the electronic warfare communication-band is presented to efficiently evaluate and optimize the performance of the direction finding system through the indoor test setup. This test-bed gives a significant benefit to the designers of the direction finding system because it allows flexible test and design trade-off in the system design cycle. The system description and implementation of test-bed architecture, and the experiment results of direction finding accuracy according to modulation schemes are presented.

• Nuclear Engineering and Technology
• /
• 제50권8호
• /
• pp.1298-1305
• /
• 2018

The use of System-on-Chip (SoC) solutions in the design of on-board data handling systems is an important step towards further miniaturization in space. However, the Total Ionizing Dose (TID) and Single Event Effects (SEE) characterization of these complex devices present new challenges that are either not fully addressed by current testing guidelines or may result in expensive, cumbersome test configurations. In this paper we report the test setups, procedures and results for TID testing of a SoC microcontroller both using standard $^{60}Co$ and low-energy protons beams. This paper specifically points out the differences in the test methodology and in the challenges between TID testing with proton beam and with the conventional gamma ray irradiation. New test setup and procedures are proposed which are capable of emulating typical mission conditions (clock, bias, software, reprogramming, etc.) while keeping the test setup as simple as possible at the same time.

• Structural Engineering and Mechanics
• /
• 제17권2호
• /
• pp.167-186
• /
• 2004

The design load-carrying capacities of wooden shores depend on factors, such as the wood species and properties, and construction methods. This paper focuses on the construction methods, including an upright single shore, group of upright shores, group of inclined shores, butt connections and lap connections. This paper reports experiments to obtain critical loads and then developed an empirical equation based on Euler' formula for the critical loads and design load-carrying capacities. The test results show that the critical loads for an upright single wooden shore are greater than the average values for a group of upright shores, and the latter are greater than the average values for a group of inclined shores. Test results also show that the critical loads become smaller when butt or lap connections are used, butt connections possessing greater critical loads than lap connections. Groups of inclined shores are very popular at work sites because they have some practical advantages even though they actually possess inferior critical loads. This paper presents an improved setup for constructing groups of inclined shores. With this method, the inclined shores have larger critical loads than upright shores. The design load-carrying capacities were obtained by multiplying the average critical loads by a resistance factor (or strength reduction factor, ${\phi}$) that were all smaller than 1. This article preliminarily suggests ${\phi}$ factors based on the test results for the reference of engineers or specification committees.

• Computers and Concrete
• /
• 제28권5호
• /
• pp.479-486
• /
• 2021

Reinforced concrete (RC) slabs are exposed to several static and dynamic effects during their period of service. Accordingly, there are many studies focused on the behavior of RC slabs under these effects in the literature. However, impact loading which can be more effective than other loads is not considered in the design phase of RC slabs. This study aims to investigate the dynamic behavior of two-way RC slabs under sudden impact loading. For this purpose, 3 different simply supported slab specimens are manufactured. These specimens are tested under impact loading by using the drop test setup and necessary measurement devices such as accelerometers, dynamic load cell, LVDT and data-logger. Mass and drop height of the hammer are taken constant during experimental study. It is seen that rigidity of the specimens effect experimental results. While acceleration values increase, displacement values decrease as the sizes of the specimens have bigger values. In the numerical part of the study, artificial neural networks (ANN) analysis is utilized. ANN analysis is used to model different physical dynamic processes depending upon the experimental variables. Maximum acceleration and displacement values are predicted by ANN analysis. Experimental and numerical values are compared and it is found out that proposed ANN model has yielded consistent results in the estimation of experimental values of the test specimens.

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권2호
• /
• pp.30-36
• /
• 1999

Superconductors are dissipative when exposed to time-varying magnetic fields. To analyze the AC characteristics of a superconductor, one usually needs to know magnetization curves of it. Good magnetization curves can be obtained only in homogeneous magnetic filed. In This paper, we report the setup and test results of a magnetization measurement system, which consists mainly of frequency-variable power supply and homeogenous magnet with 7-cm long air gap. Special emphasis are foused on the design and fabrication of the magnet, which aims to give background magnetic fields, and on the overall characteristics of the system.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.723-730
• /
• 2007

The typical design of automotive driveshafts generally utilizes Constant Velocity(CV) joints as a solution to NVH. CV joints are an integral part of vehicles and significantly affect steering, suspension, and vehicle vibration comfort levels. Thus, CV joints have been favored over universal joints due to the constant velocity torque transfer and plunging capability. Although CV joints are common in vehicle applications, current research works on modeling CV joint friction and assumes constant empirical friction coefficient values. However, such models are long known to be inaccurate, especially under dynamic conditions, which is the case for CV joints. In this paper, an instrumented advanced CV joint friction apparatus was developed to measure the internal friction behavior of CV joints using actual tripod-type joint assemblies. The setup is capable of measuring key performance of friction under different realistic operating conditions of oscillatory speeds, torque and joint installation angles. The apparatus incorporates a custom-installed triaxial force sensor inside of the joint to measure the internal CV joint forces(including friction). Using the designed test setup, the intrinsic interfacial parameters of CV joints were investigated in order to understand their contact and friction mechanisms. The results provide a better understanding of CV joint friction characteristics in developing improved automotive driveshafts.

• 대한조선학회논문집
• /
• 제54권2호
• /
• pp.125-131
• /
• 2017

In order to develop test and performance analysis techniques for a CRP propulsion, a CRP dynamometer which can be installed inside the model ship was designed and manufactured. The object ship was the 16000TEU container carrier, which has test results for the single propeller. The design concept of the present CRP is that forward & after propellers have the same power ratio and their RPM ratio is 0.75:1. To begin with, we checked the performance of the CRP dynamometer through the calibration and then installed it inside the model ship. After the model ship setup including the design CRP and the rudder in the Large Cavitation Tunnel(LCT), a series of model tests composed of power ratio check, propeller behind wake(PBW) test, cavitation observation and pressure fluctuation tests was conducted. Through the model test and data analysis for CRP, the experimental technique was established and the improved method for CRP design was suggested.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1993년도 춘계학술대회논문집; 한국과학연구소, 21 May 1993
• /
• pp.93-100
• /
• 1993

With increasing technology, requirement to car noise and related dynamics are getting competitive keypoint. Unfortunately, vibro - acoustic behavior of a car is nowadays only possible after development of prototypes. But, obviously, in the Area of Research, many of Industrials, Universities and research centers try to codevelop the design tools to predict the vibro-acoustic behaviors. At this stage, it is more realistic to represent the existing technologies in order for the engineer to get their own know-how to design and to Integrate existing techniques, to setup their test facility, and to develope some tools with which they can successfully predict noise levels of car in the design phase. Moreover, most of the theories which will be represented in this paper can be used in the design phase. At any way, finding the cause of trouble shooting is more urgent than the design of a car to the test engineer. In this paper, transfer path analysis, noise source identification, and the key test method of modal analysis is introduced. Later, if I get the opportunity to present in KSNVE, the approach method of modal analysis is introduced. Later, if I get the opportunity to present in KSNVE, the approach method of finding characteristics of joint and welding part will be introduced. Most parts of this paper was quoted from the papers of LMS.