• 한국의학물리학회지:의학물리
• /
• 제33권4호
• /
• pp.164-171
• /
• 2022

The number of facilities using radiation generators increases and related regulations are strengthened, the establishment of a shielding management and evaluation technology has become important. The characteristics of the radiation generator used in previous report differ from those of currently available high-frequency radiation generators. This study aimed to manufacture lead, iron, and concrete shielding materials for the re-verification of half-value layers, tenth-value layers, and attenuation curve. For a comparison of attenuation ratio, iron, lead, and concrete shields were manufactured in this study. The initial dose was measured without shielding materials, and doses measured under different types and thicknesses of shielding material were compared with the initial dose to calculate the transmission rate on 50-300 kVp X-ray. All the three shielding materials showed a tendency to require greater shielding thickness for higher energy. The attenuation graph showed an exponential shape as the thickness decreased and a straight line as the thickness increased. The difference between the measurement results and the previous study, except in extrapolated parts, may be due to the differences in the radiation generation characteristics between the generators used in the two studies. The attenuated graph measured in this study better reflects the characteristics of current radiation generators, which would be more effective for shield designing.

• Nuclear Engineering and Technology
• /
• 제53권5호
• /
• pp.1634-1641
• /
• 2021

Exposure to gamma-rays is hazardous for humans and other living beings because of their high penetration through the materials. For this reason, shielding materials (usually lead, copper and stainless steel) are used to protect against gamma rays. This study's objective was to prepare ceramic materials for gamma radiation shielding by using different natural bentonite clays. Gamma-ray attenuation performances of the prepared shielding materials at different thicknesses were investigated and evaluated for different gamma-ray energies from different standard point gamma radiation sources (²⁵¹Am, ⁵⁷Co, ¹³⁷Cs, ⁶⁰Co, and ⁸⁸Y). The mass and linear attenuation coefficients of the prepared ceramics vary between 0.238 and 0.443 cm² g^-1 and between 0.479 and 1.06 cm^-1, respectively, depending on their thicknesses. Results showed that these materials could be prioritized because of their evidential properties of gamma radiation protection in radiation applications.

• Nuclear Engineering and Technology
• /
• 제54권1호
• /
• pp.318-325
• /
• 2022

In this study, composites containing undoped and barium-doped Bi₂WO₆:Ba²⁺were investigated for their shielding against diagnostic X-ray. At first, Bi₂WO₆ and barium-doped Bi₂WO₆ were synthesized with different weight percentages of barium oxide through a hydrothermal process. The as-synthesized nanostructures were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and Raman spectroscopy (RS). After that, some shields were generated with undoped and barium-doped Bi₂WO₆:Ba²⁺ nanostructure particles incorporated into polyvinyl chloride (PVC) polymer with different thicknesses and 15% weight of the nanostructure. Finally, the prepared samples were exposed to an X-ray tube at 40, 80, and 120 kV voltages, 10 mAs and, 44.5 cm SID (i.e. the distance from the X-ray beam source to the specimen). Linear and mass attenuation coefficients were also calculated for different samples. The results indicated that, among the samples, the one with 7.5 mmol barium-doped Bi₂WO₆ had the most attenuation at the voltage of 40kV, and the attenuation coefficients would increase with an increase in the amount of barium. The samples with 15 and 17.5 mmol barium-doped Bi₂WO₆ had higher attenuation than the others at 80 and 120 kV. Moreover, the half-value layer (HVL), tenth-value layer (TVL) and 0.25 mm lead equivalent thickness were calculated for all the samples. The lowest HVL value was for the sample with 7.5 mmol barium-doped Bi₂WO₆. As the result clearly show, an increment in the barium-doping content leads to a decrease in both HVL and TVL. In every three voltages, 0.25 mm lead equivalent thickness of the barium-doped composites (7.5 mmol and 15 mmol) had less than the other composites. The lowest value of 0.25 mm lead equivalent thickness was 7.5 barium-doped in 40 kV voltage and 15 mmol barium-doped in 80 kV and 120 kV voltages. These results were obtained only for 15% weight of the nanostructure.

• Nuclear Engineering and Technology
• /
• 제55권4호
• /
• pp.1218-1224
• /
• 2023

We investigated the radiation shielding competence for TeO₂-V₂O₅-MoO₃ glasses. The Phy-X software was used to report the radiation shielding parameters for the present glasses. With an increase in TeO₂ and MoO₃ content, the samples' linear attenuation coefficient improves. However, at low energies, this change is more apparent. At low energy, the present samples have an effective atomic number (Z_eff) that is relatively high (in order of 16.17-24.48 at 0.347 MeV). In addition, the findings demonstrated that the density of the samples is a very critical factor in determining the half value layer (HVL). The minimal HVL for each sample can be found at 0.347 MeV and corresponds to 1.776, 1.519, 1.391, 1.210 and 1.167 cm for Te1 to Te5 respectively. However, the highest HVL of these glasses is recorded at 1.33 MeV, which corresponds to 3.773, 3.365, 3.218, 2.925 and 2.908 cm respectively. The tenth value layer results indicate that the thickness of the specimens needs to be increased in order to shield the photons that have a greater energy. Also, the TVL results demonstrated that the sample with the greatest TeO₂ and MoO₃ concentration has a higher capacity to attenuate photons.

• 한국의류산업학회지
• /
• 제12권1호
• /
• pp.114-121
• /
• 2010

Denim is one of the most frequently used fabrics for blue jeans. After washing denim fabric frequently changes its size and color. Salespersons recommended that after purchasing blue jeans customers should dry clean them once before washing. The aim of this study was to investigate to what degree washing with a household washing machine and dry cleaning affected the dimensions and the color of denim fabric. The denim fabric shrank greatly after the first laundering in warp direction regardless of whether it had been dry-cleaned or not. However, it shrank little from the second to the tenth laundering and after each number of dry cleanings. The thickness of the denim changed in the same way as the shrinkage occurred when the number of launderings or dry-cleanings increased. Although the indigo came out of the denim into washing liquor, both of the $L^*$ values and the $b^*$ values of the laundered and the dry-cleaned denim fabrics were lower than those of the control fabric. Darkening of the fabric after washing attributed to the shrinkage in warp; specifically the deep-blue warp yarns more spaced on the fabric face and the back. The $L^*$ and $b^*$ values of the dry-cleaned fabric decreased less than those of the laundered. The value of $a^*$ increased much less than the other values. Staining of the white cotton fabric laundered with the denim fabrics became less as the number of launderings increased. The degree of staining from the dry-cleaned denim was much lower than that of the laundered fabric.