• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.837-846
• /
• 1989

본 연구에서는 일반적인 평벨트 구동의 Eytelwein식을 이용하여 가공물이 풀리와 풀리사이의 벨트에서 연삭되는 벨트 접촉식 연삭에서 벨트 장력분포를 이론 및 실험적으로 구하고 벨트와 풀리사이의 내접촉 특성을 밝혀 벨트 연삭장치의 효율 개선을 위한 설계자료를 구하고자 하였다.

• 한국산학기술학회논문지
• /
• 제11권9호
• /
• pp.3599-3609
• /
• 2010

연안개발과 해안매립을 사용하여 개발된 새로운 도시 건설의 수요가 증가하면서 해안구조물과 고층구조물의 시공이 증가하는 추세이다. 이러한 구조물에서 수평력과 인발력을 받는 구조물의 기초의 적용이 증가하고 있으며, 특히 구조물에서 인발력에 효과적으로 저항하기 위한 기초형식으로 선단확장형말뚝의 사용이 증가하고 있는 실정이다. 압축력을 받는 기초에 관한 많은 연구들이 이루어지고 있으나, 선단확장형말뚝의 인발저항에 관한 연구는 미비한 상태이다. 따라서 본 논문에서는 국외 4개 현장을 대상으로 선단확장형말뚝을 시공하고 정재하시험을 실시하여 말뚝의 지지력 및 하중-변위특성과 주면마찰력을 고려한 하중분담을 고찰하였다. 또한 3차원 유한요소해석 및 이론에 의해 산정된 극한인발력과 현장시험의 극한인발력을 비교 평가하였다.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.44-49
• /
• 2011

The crawler crane, which consists of a lattice boom, a driving system, and movable vehicle, is widely used in a construction site. It needs to be installed an overload limiter to prevent the overturning accident and the fracture of structure. This research is undertaken to provide the relation formula for designing the overload limiter as follows: First the relation formulas between the wire-rope tension and the hoisting load or the overturning ratio according to the luffing angle and length of a lattice boom are established. Secondly the derived formulas are corrected by using the compensated angle considering the deflection of boom through the finite element analysis. The stiffness analysis is carried out for 30-kinds of models as a combination of 6-kinds of luffing angle and 5-kinds of length of boom. Finally the shape design of a stick type load cell, which is the device to measure the wire-rope tension, is performed. 5-kinds of notch radius and 5-kinds of center hole radius are adopted as the design parameter for the strength analysis of the load cell.

• 대한기계학회논문집A
• /
• 제29권8호
• /
• pp.1118-1122
• /
• 2005

The direct current potential drop (DCPD) method and the unloading compliance (UC) method with a crack opening displacement gauge were applied simultaneously to the Zr-2.5Nb curved compact tension (CCT) specimens to determine which of the two methods can precisely determine the crack initiation point and hence the crack length for evaluation of their fracture toughness. The DCPD method detected the crack initiation at a smaller load-line displacement compared to the UC method. As a verification, a direct observation of the fracture surfaces on the curved compact tension specimens was made on the CCT specimens experiencing either 0.8 to 1.0 mm load line displacement or various loads from $50\%\;to\;80\%$ of the maximum peak load, or $P_{max}$. The DCPD method is concluded to be more precise in determining the crack initiation and fracture toughness, J in Zr-2.5Nb CCT specimens than the UC method.

• 기술발표회
• /
• 통권2006호
• /
• pp.66-72
• /
• 2006

The ground anchoring has been utilized over 40 years. It is growing the application of the removal ground anchor with tension force for holding earth retaining constructions in the city. It transmits tension stress of prestressed steel wire through grouting to fixed the ground that is of great advantage adjacent ground stability. Nowadays, we can find the compression dispersion anchor on many site. But, it has some problems in behavior of anchors because of impossible to tense p.c strand uniformly under the existing equipment due to different length of p c strand. Hence, motive of this research was to study the application of the newly developed tension system, that analyze and compare with the current anchoring method build on the data of in-site test and laboratory test. As a result, in case of auto back tension system, it became clear that tension pressure was equally distributed among the steal wires but the existing tension system showed sign of instability by indicating stress deflection of about 30% compare with design load. This can cause an ultimate failure of the concentrated p.c strand and a shear failure of ground.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.450-454
• /
• 2003

Natural periods are usually determined by the so-called linearized finite displacement theory even for a suspension bridge. This linearized method, with formulating structural stiffness by taking dead-load tension into consideration, calculates the natural periods of the bridge. As a result, the assumed initial tensions for each cable member may affect the accuracy of calculated natural periods and some other dynamic responses. This paper mainly demonstrates the effect of initially introduced tension accuracy on the evaluation of dynamic characteristics for a suspension bridge.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1777-1784
• /
• 2001

This paper provides d simplified engineering J estimation method fur semi-e1liptical surface cracked plates in tension, based on the reference stress approach. Note that the essential element of the reference stress approach is the plastic limit lead in the definition of the reference stress. However, for surface cracks, the definition of the limit load is ambiguous ("local" or "global"limit lead), and thus the most relevant limit load (and thus reference stress) for the J estimation should be determined. In the present work, such limit load solution is found by comparing reference stress bated J results with those from extensive 3-D finite element analyses. Validation of the proposed equation against FF J results based on tactual experimental tensile data of a 304 stainless steel shows excellent agreements not only far the J values at the deepest point but also for those at an arbitrary paint along the crack front, including at the surface point. Thus the present results provide a good engineering tool for elastic-plastic fracture analyses of surface cracked plates in tension.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.281-284
• /
• 2006

ASCE-ACI Committee 426 and 445, on Shear and Torsion, well noted in their report that recent research work regarding shear and torsion had been devoted primarily to members. But it was not logical approach of PSC members applied by axial force based on the shear deformation in web element. And it was not included that the effect of axial is to shift the shear strain(or crack width) in the web element versus the applied shear curve up or down by the amount by which the biaxial tension-compression state varies. The shear strength also increases or decreases, so that the change in shear strain at service load due to the presence of axial load is to some extent changed. Generally, in corresponding beams the shear strain at service load is less in the beam subject to axial compression and greater in the beam subject to axial tension, than in the beam without axial load. In particular, however, no research were available on the shear deformation in shear of PSC members with web reinforcement, subject to axial force in addition to shear and bending. Therefore, this study was basically performed to develop the program for the calculation of the shear deformation based on the shear effect of axial force in prestressed concrete members.

• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.3112-3121
• /
• 2021

One of the major factors affecting the life span of a Reactor Pressure Vessel (RPV) is the Pressurised Thermal Shock (PTS). PTS is a thermo-mechanical load on the RPV wall due to steep temperature gradients and structural load created by internal pressure of the fluid within the RPV. Safe operating life of a nuclear power plant is ensured by carrying out fracture analysis of the RPV against thermal shock. Carrying out fracture tests on RPV/large scale components is not always feasible. Hence, studies on laboratory level specimens are necessary to validate and supplement the prototype results. This paper aims to study the fracture behaviour of standard Compact Tension [C(T)] specimens, made of RPV steel 20MnMoNi55, subjected to thermal shock through experimental and numerical investigations. Fracture tests have been carried out on the C(T) specimens subjected to thermal transient load and tensile load to quantify the effect of thermal shock. Crack resistance curves are obtained from the fracture tests as per ASTM E1820 and compared with those obtained numerically using XFEM and a good agreement was found. A quantitative study on the crack tip plastic zone, computed using cohesive segment approach, from the numerical analyses justified the experimental crack initiation toughness.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권6호
• /
• pp.948-954
• /
• 2008

Now, but task for stringing trolley wire is worked manually by a measurement of dip, we need to development the automatic control system for a safety and effective tasks. In this paper, in works of stringing trolley wire by a mobile of robot, a method is proposed tension control for the stringing trolley wire. On the basics of a wire model with hard nonlinear, ac servo motor model for torque generating and stringing wire tension, the tension control scheme is design and implemented with a detected wire tension by a load cell. We experimentally show that the performance of the tension response are satisfactory to regulator tension. The proposed system is simulated and experimented, results is verified the utilities.