• Advances in concrete construction
• /
• 제9권2호
• /
• pp.195-205
• /
• 2020

In this study, effect of recycled aggregates and polypropylene fibers on the response of conventionally reinforced concrete element subjected to tensile loading in terms of tension stiffening and strain development was experimentally investigated. For this purpose, concrete prisms of 100 × 100 mm cross section and 500 mm length having one central deformed steel re-bar were cast using fibrous and non-fibrous Recycled Aggregate Concrete (RAC) with varying percentages of recycled aggregates (0%, 25%, 50%, 75% and 100%) and tested under uniaxial tensile load. For all fibrous RAC mixes, polypropylene fibers were used at constant dosage of 3.15 kg/㎥. Effect of recycled aggregates and fibers on the compressive strength of concrete was also explored in this study. Through studying tensile load versus global axial deformation of composite and strain development in concrete and steel, it was found that replacement of natural aggregates with recycled aggregates in concrete negatively affected the cracking load, tension stiffening and strain development, and this negative effect was observed to be increased with increasing contents of recycled aggregates in concrete. The results of this study showed that it was possible to minimize the negative effect of recycled aggregates in concrete by the addition of polypropylene fibers. Reinforced concrete element constructed using concrete containing 50% recycled aggregates and polypropylene fibers exhibited cracking behavior, tension stiffening and strain development response almost similar to that of concrete element constructed using natural aggregate concrete without fiber.

• Journal of Welding and Joining
• /
• 제35권2호
• /
• pp.23-29
• /
• 2017

Mechanical properties and hardness distributions in arc brazed joints of Dual phase steel using Cu-Al insert metal were investigated. The maximum tensile shear load was 10.4kN at the highest brazing current. It was about 54% compared to tensile load of base metal. This joint efficiency is higher than that of joint of DP steel using Cu-based filler metals which are Cu-Si, Cu-Sn. Fracture positions can be divided into two types. Crack initiation commonly occurred at three point junction among upper sheet, lower sheet and the fusion zone. However crack propagations were different with increasing the brazing current. In case of the lower current, it instantaneously propagated along with the interface between fusion zone and upper base material. On the other hand, in case of higher current, a crack propagation occurred through fusion zone. When the brazing current is low (60, 70A), the interface shape is flat type. However the interface shape is rough type, when the brazing current is high (80A). It is thought that the interface shapes were the reason why the crack propagations were different with brazing current. The interface was the intermetallic compounds which consisted of $(Fe,Al)_{0.85}Cu_{0.15}$ IMC formed by crystallization at $1200^{\circ}C$during cooling. Therefore the maximum tensile shear load and the fracture behavior were determined by a interface shape and effective sheet thickness of the fracture position.

• 한국건설순환자원학회논문집
• /
• 제8권3호
• /
• pp.349-355
• /
• 2020

이 연구의 목적은 섬유의 혼입량과 종류에 따른 고강도 섬유보강 복합재료의 정적하중에서의 압축강도 및 인장거동과 비상체 하중 하에서의 충격 저항성을 조사하고자 한다. 이를 위하여 3가지 배합을 설계하였고, 압축강도, 직접인장, 그리고 고속 비상체 충돌 실험을 수행하였다. 실험결과 섬유의 혼입량은 압축강도에 비하여 인장강도에 큰 영향을 미치며, 하이브리드 섬유 사용으로 인장변형성능이 향상되는 것으로 나타났다. 강섬유의 혼입량은 충격 저항성에 큰 영향을 미치는 것으로 나타났다. 하이브리드 섬유를 사용하면 충격 저항성이 더욱 향상되는 것으로 나타났다. 다만, 단일 섬유 사용에 비하여 실험체별성능 차이가 크게 발생하는 것으로 나타났다.

• Design & Manufacturing
• /
• 제18권2호
• /
• pp.17-22
• /
• 2024

Lightweight of plastic containers is becoming an important issue due to increasing environmental legislation and consumer awareness. In this study, the CAE analysis was conducted to optimize the shape of a 500 ml lightweight square polyethylene terephthalate(PET) bottle. First, the linear buckling alaysis using the finite element method was performed to analyze the correlation between the primary geometric parameters of the bottle and the buckling critical load. Then, the optimal geometry parameters were derived, and the actual buckling load was predicted by non-linear buckling simulation. The validity of the simulation results was verified by top-loading tests of PET bottles molded with the optimized geometry. The elastic modulus and tensile yield strength of PET through tensile tests were measured to improve the accuracy of the simulation. As a result of the tensile tests, the modulus of elasticity of PET increased from 2,900 MPa to 4,275 MPa, and the tensile yield strength increased from 52.4 MPa to 88.1 MPa. Finally the buckling load of the optimized PET bottle was found to be approximately 236 N, which is very similar to the simulation precition of 238 N. This study shows the feasibility and accuracy of the CAE analysis approach for the lightweight design of PET bottles, and will provide useful guidelines for the design of PET bottles.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1538-1545
• /
• 2005

Theoretical and experimental result studies of the unconfined penetration test (UP) method are conducted to suggest a new test method by improving the UP method for determination of the tensile strength of compacted fine-grained soils. From the theoretical aspect, the tensile strength of the specimen is estimated from the maximum load by the theory of perfect plasticity with assumptions, sufficient local deformability and modified Mohr-Coulomb failure criterion. Experimentally, some factors including relative size of specimen-disc, disc diameter, and loading rate are needed more study, because these factors significantly affect the results of tensile strength. Improvement of the alignement between two discs and specimen in the UP test is also necessary to eliminate the error due to eccentrically loading.

• 한국정밀공학회지
• /
• 제14권7호
• /
• pp.91-98
• /
• 1997

Because of a complicated behavior of fatigue in mechanical structures, the analysis of fatigue is in need of much researches on life prediction. A method is developed for the dynamic tensile strength analysis by simple tensile test, which is for the failure life prediction by lethargy coefficient of various materials. Then it is programed to analyze the failure life prediction of mechanical system by virtue of fracture. Thus the dynamic tensile strength analysis is performed to evaluate life parameters as a numerical example, using the developed method.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.202-205
• /
• 2003

Investigated whether fiber orientation situation of fiber reinforcement macromolecule composition board and the fiber inclusion rate are perpendicular and horizontal direction tensile strength and some correlation. Fiber orientation situation of tensile strength of 0 direction of composition board increased changelessly by aeolotropy in isotropy. Tensile strength of 90 direction that is isotropy and tensile strength of 0 direction that is aeolotropy agreed almost. Get into aeolotropy, the reinforcement rate of fiber decreased. When load interacts for width direction of reinforcement.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.231-236
• /
• 2001

A newly developed Advanced Indentation System (AIS), which is a portable and nondestructive system for evaluating tensile properties, was used to measure mechanical behavior of materials used under high temperature and pressure conditions. This test measures indentation load-depth curve during indentation and analyzes the mechanical properties related to deformation and fracture. Aging effects of Cr-Mo and Cr-Mo-V steel at high temperature were simulated. Tensile properties including yield strength and tensile strength at various temperature are obtained from the test. For all test materials and conditions, the AIS-derived results were in good agreement with those from conventional standard test method. Examples of the test results ate given and potential applications of the AIS to assess the integrity of aging structures are briefly discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.21-24
• /
• 2007

This paper deals with introduction of testing equipments for the evaluation of dynamic tensile characteristics of auto-body steel sheets and the crashworthiness of auto-body members. The servo-hydraulic high speed material testing machine was developed for tensile tests at the intermediate strain rate to obtain the tensile material properties at the strain rate under 500/sec. The split Hopkinson bar apparatus using the elastic wave was developed for dynamic material characteristics at the high strain rate ranged from 1,000 to 10,000/sec. The servo-hydraulic high speed crash testing machine is the equipment for the evaluation of the collapse load and crashworthiness of auto-body members. High speed carrying truck crashes to specimen with the maximum velocity of 17 m/sec.

• 대한토목학회논문집
• /
• 제12권2호
• /
• pp.67-76
• /
• 1992

본 연구에서는 아스팔트 콘크리트 포장구조체의 제한교통하중 산정과정을 제안하였다. 제한교통하중은 아스팔트 콘크리트 포장구조체의 파괴기준이 되는 노상상단의 연직변형율과 아스팔트 안정처리 기층 최하단에서의 인장변형용을 포장구조체 모델에 따른 바퀴의 영향선을 고려하여 산정한 후 포장 구조체의 변형율과 축하중과의 관계에 설계한계치를 적용하여 산정한다. 본 연구에서는 우리나라 고속도로중 경부선, 경인선, 영동선 확장구간 모델의 제한교통하중을 산정하기 위하여 바퀴의 영향선을 고려하여 변형율을 산정하였다. 제한교통하중의 기준은 세계 여러 관계기관에서 제안한 파괴기준식으로부터 설계한계치를 산정하여 이용하였다. 축구성(단축, 탄뎀축, 트라이뎀축)에 따른 제한교통하중을 분석한 결과 제한교통하중은 포장구조체의 두께와 밀접한 관계가 있음을 알 수 있었다. 또한 탄뎀축과 트라이뎀축의 제한교통하중은 단축의 제한교통하중에 축 수를 곱하여 구한 값과 유사함을 알 수 있었다. 따라서 본 연구에서는 제한교통하중을 단축기준의 제한교통하중으로 제안하였다. 단축기준의 제한교통하중은 우리나라 고속도로중 경부선, 경인선, 영동선 확장구간을 대상으로 해석한 결과, 인장변형율에 의한 제한교통하중이 연직변형율에 의한 제한교통하중보다 포장구조체에 미치는 영향이 더 큼을 알 수 있었다.