• 한국기계가공학회지
• /
• 제12권2호
• /
• pp.62-67
• /
• 2013

The influence of internal stress and joint strength(shear, tensile) according to the deposition conditions was investigated by the Polyimide substrate and ZnO thin film. Deposition thickness and temperature affect the internal stress and the internal stress was minimum at the 60nm and $200^{\circ}C$ of the deposition conditions. Tensile strength is large at the deposition condition that shear strength is large and the shear strength was about 50% of the tensile strength. The shear strength and tensile strength were large at deposition condition that internal stress was small. Crack occurred near the joint interface of Polyimide substrate and progressed along the interface until the final fracture.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.89-96
• /
• 2004

Micro-tensile testing system, consisting of a micro tensile loading system and micro-ESPI(Electronic Speckle Pattern Interferometry) system, has been developed for measurement of micro-tensile properties of thin micro-materials. Micro-tensile loading system had a load cell with the maximum capacity of 50N and micro actuator with resolution of 4.5nm in stroke. The system was used to apply a tensile load to the micro-sized specimen. During tensile loading, the micro-ESPI system acquired interferornetric speckle patterns in the deformed specimen and measured the in-plane tensile strain. The ESPI system consisted of a CCD-camera with a lens and the window-based program developed for this experiment. Using this system, stress-strain curves for 4 kinds of electrolytic copper foil 18$\square$m thick were obtained. From these curves, tensile properties, including the elastic modulus. yielding strength and tensile strength, were determined and also values of the plastic exponent and coefficient based on Ramberg-Osgood relationship were evaluated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.579-580
• /
• 2006

In this study, an injection mold of tensile test specimen was manufactured by international standard. Pressure and temperature in the cavity of the injection mold was measured by sensors. Simulation of injection molding process was performed with the same condition of experiment and linear structural tensile analysis was also performed with the initial condition of the residual stress induced by injection molding analysis. Normalized elastic coefficient of tensile test was compared with that of structural analysis. It was shown that the residual stress induced by injection molding has an effect on both the experiment of tensile test and linear structural analysis.

• Journal of Welding and Joining
• /
• 제22권4호
• /
• pp.50-58
• /
• 2004

In this study, high temperature tensile properties of high strength steels(POSTEN60, POSTEN80) were investigated. The three-dimensional thermal elastic-plastic analyses were conducted to investigate the characteristics of welding residual stresses in welds of high strength steels on the basis of thermal and mechanical properites at high temperature obtained from the experiment. According to the results, high temperature tensile strength of POSTEN60 steel deteriorated slowly to 10$0^{\circ}C$. As the temperature went up, the tensile strength became better because of blue shortness, and it deteriorated radically after reaching to the maximum value around 30$0^{\circ}C$. For the POSTEN80 steel, high temperature tensile strength deteriorated slowly to 20$0^{\circ}C$. As the temperature went up the tensile strength became better and it deteriorated slowly to $600^{\circ}C$ after reached to the maximum value around 30$0^{\circ}C$. Strain of high strength steels at the elevated temperature increased radically after the mercury rose to $600^{\circ}C$. The strain hardening ratio of POSTEN60 steel was larger then that of POSTEN80 steel at the elevated temperature as in the case at the room temperature and it became smaller radically after the mercury rose to 40$0^{\circ}C$. And, in the welding of high strength steels, increasing tensile strength of the steel (POSTEN60

• 한국재료학회지
• /
• 제12권10호
• /
• pp.820-824
• /
• 2002

It is of importance to know that the bonding strength and interfacial stress of SOI wafer pairs to meet with mechanical and thermal stresses during process. We fabricated Si/2000$\AA$-SiO$_2$ ∥ 2000$\AA$-SiO$_2$/Si SOI wafer pairs with electric furnace annealing, rapid thermal annealing (RTA), and fast linear annealing (FLA), respectively, by varying the annealing temperatures at a given annealing process. Bonding strength and interfacial stress were measured by a razor blade crack opening method and a laser curvature characterization method, respectively. All the annealing process induced the tensile thermal stresses. Electrical furnace annealing achieved the maximum bonding strength at $1000^{\circ}C$-2 hr anneal, while it produced constant thermal tensile stress by $1000^{\circ}C$. RTA showed very small bonding strength due to premating failure during annealing. FLA showed enough bonding strength at $500^{\circ}C$, however large thermal tensile stress were induced. We confirmed that premated wafer pairs should have appropriate compressive interfacial stress to compensate the thermal tensile stress during a given annealing process.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.1085-1088
• /
• 2008

철근공사에서 이음은 필연적으로 발생되며, 일반적으로 겹침이음을 통해 이음강도를 확보한다. 인장 이음길이는 인장 정착길이를 기준으로 산정되며, 정착길이는 실험적으로 도출된 부착강도 모델을 기반으로 결정된다. 인장이음은 휨을 받는 경우에 발생되므로 부재의 휨변형이 반드시 발생된다. 휨변형에의해 프라이(Prying) 거동이 발생되어, 철근이 피복콘크리트를 밀어내는 힘이 발생된다. 이러한 힘은 부착응력에 의해 발생되는 인장응력과 동일한 역할을 한다. 프라이 거동에 의해 발생된 인장응력과 부착응력에 의해 발생된 인장응력의 합이 콘크리트 인장강도에 도달하면 이음부가 파괴되므로, 프라이거동의 존재는 부착강도를 저하시키게 된다. 역학적 모델을 구성하여 휨부재의 인장이음에서 프라이거동이 이음강도에 미치는 영향을 분석하였다. 프라이 거동에 의한 인장응력은 보강근의 인장강도와 탄성계수에 비례하며, 휨부재의 휨강성에도 영향을 받는 것으로 나타났다. 또한 이음되는 보강근의 간격에 반비례하여 인장응력이 유발된다. 따라서 슬래브와 같이 휨강성이 작은 부재에 촘촘하게 이음된 경우에는 현행 설계기준보다 긴 이음길이를 확보할 필요가 있다.

• 한국산학기술학회논문지
• /
• 제19권12호
• /
• pp.25-31
• /
• 2018

선택적 레이저 용융 (Selective Laser Melting) 기법은 금속 소재를 다루는 대표적인 3D 프린팅 기법중의 하나이다. SLM 기법으로 제작되는 구조물의 특성을 좌우하는 주요 제작 인자로는 구조물의 적층 제작 방향, 레이저 파워, 레이저 스캔 스피드 및 스캔 간격 등을 고려할 수 있다. 이번 연구에서는 AlSi10Mg 합금을 대상 소재로 하여, 인장 시편의 제작 방향, 레이저 스캔 스피드 및 스캔 간격을 변수로 하여, 인장특성 결과를 비교 분석하였다. 인장특성으로는 항복 응력, 인장강도 및 연신율을 고려하였다. 시험결과로부터, 인장 시편의 제작 방향 기준으로 0도, 45도, 90도 순서로 항복 응력 값이 낮아짐을 확인하였다. 레이저 스캔 스피드 기준으로는 1870mm/min에서 가장 큰 항복 응력값을 보였으며, 스캔 스피드가 낮아질수록 항복 응력 크기도 줄어들었다. 레이저 스캔 간격 기준으로, 그 크기가 증가할수록 항복 응력값은 증가하지만, 다른 시험 기준에 비해 그 변화폭은 가장 적었다. 인장강도 및 연신율은 시험조건에 따른 명확한 경향성을 파악하기 어려웠다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1585-1587
• /
• 2008

Fibroblast is constantly subjected to mechanical loads in connective tissues where mechanical signals are converted to intercellular biochemical events. The aim of this study is to understand the effects of tensile stress on the neurotrophin (NT) and transforming growth factor (TGF) expression of fibroblast in vitro. Nerve growth factor (NGF) stimulates fibroblast migration, and TGF is related to tissue repair. In this study, at the uniaxial stretch of 10% strain and frequency of 0.5 Hz, different resting times of 0, 20, and 60 min are placed in between 10 min stimulations periods. Results show increase in NGF mRNA levels and a substantial decrease in NT3 mRNA after 1 hr of stimulation, indicating that the tensile stress may regulate NGF and NT3, key factors for the neurocosmetic applications. The mRNA level for TGF-${\alpha}$ and TGF-${\beta}2$ had increased up to two-folds after 1 hr of stimulation, showing that the tensile stress may control TGF, an important part of wound healing.

• 대한건축학회논문집:구조계
• /
• 제35권3호
• /
• pp.27-33
• /
• 2019

The purpose of this study is to provide and evaluate the tensile properties of masonry element such as tensile strength, strain, modulus of elasticity and stress-strain relationship through the direct tension test with varies of mortar strength. From the experiment, the tension fracture was observed along the interfaces between the brick and the mortar. Tension properties of masonry element was significantly affected by compressive strength of mortar, $f_m$, indicating that higher tensile strength and modulus of elasticity of masonry element were obtained with increase of $f_m$. The strain of a masonry element was inversely proportional to $f_m$ due to the lower ductility of a higher mortar strength. A tensile stress-strain relationship of masonry element was generalized based on the numerical analysis and the regression analysis using test data. The proposed model shows fairly good agreement with the test measurements.

• Journal of the Korean Wood Science and Technology
• /
• 제31권3호
• /
• pp.35-41
• /
• 2003

The mechanical and physical properties of wood are strongly dependent upon the slope of grain. Specially, tensile strength is more severely affected by the slope of grain. Therefore, tension tests were performed on small thin wood samples made from Pinus radiata with varying the slope of grain. Determining the tensile strength for clear thin wood samples the other variabilities associated with material, size, drying, defects, etc were discarded. Slope of grain was measured by the slope of grain indicator and actual slope of grain was also determined by a protractor. Correlation coefficients between machine measured and actual slope of grain for 40 pieces of 2×20 mm, 300 mm long Pinus radiata were 0.84 for wide face measurement. Results also showed that tensile strength and MOE from stress wave tests decreased with increasing the slope of grain. This study did not establish a relationships for tensile strength and MOE from stress wave with slope of grain. However, the trends of MOEs from stress wave test with both slope of grain are agreed well with Hankinson's equation. Predicted tension strength curve by Hankinson's equation was also agreed well with the experimental data over the range from 0 to 13 degrees for slope of grain.