• 항공우주시스템공학회지
• /
• 제15권6호
• /
• pp.19-25
• /
• 2021

This paper presents a method that uses the stress failure criteria to predict the tensile failure strength of open-hole laminates with stress concentrations. The composite material used in this study corresponds to a 177 ℃ cured, carbon/epoxy unidirectional tape prepreg. The results obtained by testing ten different laminates were compared and analyzed to verify the tensile strength of the open-hole laminates predicted using the proposed stress failure criteria. The findings of this study confirm that the tensile strength predictions performed using the proposed method are generally accurate, except in cases involving highly soft laminates (10% of 0° ply).

• Geomechanics and Engineering
• /
• 제23권5호
• /
• pp.467-480
• /
• 2020

The failure behavior and tensile strength of sandstone materials under different strain rates are greatly different, especially under static loads and impact loads. In order to clearly investigate the failure mechanism of sandstone materials under static and impact loads, a series of Brazilian disc samples were used by employing green sandstone, red sandstone and black sandstone to carry out static and impact loading splitting tensile tests, and the failure properties subjected to two different loading conditions were analyzed and discussed. Subsequently, the failure behavior of sandstone materials also were simulated by finite element code. The good agreement between simulation results and experimental results can obtain the following significantly conclusions: (1) The relationship of the tensile strength among sandstone materials is that green sandstone < red sandstone < black sandstone, and the variation of the tensile sensitivity of sandstone materials is that green sandstone > red sandstone > black sandstone; (2) The mainly cause for the difference of dynamic tensile strength of sandstone materials is that the strength of crystal particles in sandstone material, and the tensile strength of sandstone is proportional to the fractal dimension; (3) The dynamic failure behavior of sandstone is greatly different from that of static failure behavior, and the dynamic tensile failure rate in dynamic failure behavior is about 54.92%.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.1013-1021
• /
• 2001

A series of rabbit common extensor tendon specimens of the humeral epicondyle were subjected to tensile tests under two displacement rates (100mm/min and 10mm/min) and different elbow flexion positions 45°, 90°and 135°. Biomechanical properties of ultimate tensile strength, failure strain, energy absorption and stiffness of the bone-tendon specimen were determined. Statistically significant differences were found in ultimate tensile strength, failure strain, energy absorption and stiffness of bone-tendon specimens as a consequence of different elbow flexion angles and displacement rates. The results indicated that the bone-tendon specimens at the 45°elbow flexion had the lowest ultimate tensile strength; this flexion angle also had the highest failure strain and the lowest stiffness compared to other elbow flexion positions. In comparing the data from two displacement rates, bone-tendon specimens had lower ultimate tensile strength at all flexion angles when tested at the 10mm/min displacement rate. These results indicate that creep damage occurred during the slow displacement rate. The major failure mode of bone-tendon specimens during tensile testing changed from 100% of midsubstance failure at the 90°and 135°elbow flexion to 40% of bone-tendon origin failure at 45°. We conclude that failure mechanics of the bone-tendon unit of the lateral epicondyle are substantially affected by loading direction and displacement rate.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.936-938
• /
• 2017

본 논문에서는 발사체 및 무기체계의 연소관 등에 적용되고 있는 복합재의 볼트체결부에 대한 점진적 파손 해석을 수행하였다. 해석에 사용된 Hashin 파손 판정식은 복합재 파손모드에 따라 섬유 인장 파손 모드(Fiber tensile failure mode), 섬유 압축 파손 모드(Fiber compressive failure mode), 기지 인장 파손 모드(Matrix tensile failure mode), 기지 압축 파손 모드(Matrix compressive failure mode)의 4가지 모드로 고려되었으며, 이를 이용해 user subroutine인 UMAT을 개발하였다. 점진적 파손 해석을 통해 복합재 볼트체결부에 대한 파손강도를 예측 하였으며, 이를 시편 시험 결과와 비교하였다.

• Advanced Composite Materials
• /
• 제16권2호
• /
• pp.167-180
• /
• 2007

The tensile strength of unidirectional carbon fiber reinforced plastics under a high strain rate was experimentally investigated. A high-strain-rate test was performed using the tension-type split Hopkinson bar technique. In order to obtain the tensile stress-strain relations, a special fixture was used for the impact tensile specimen. The experimental results demonstrated that the tensile modulus and strength in the longitudinal direction are independent of the strain rate. In contrast, the tensile properties in the transverse direction and the shear properties increase with the strain rate. Moreover, it was observed that the strain-rate dependence of the shear strength is much stronger than that of the transverse strength. The tensile strength of off-axis specimens was measured using an oblique tab, and the experimental results were compared with the tensile strength predicted based on the Tsai-Hill failure criterion. It was concluded that the tensile strength can be characterized quite well using the above failure criterion under dynamic loading conditions.

• Computers and Concrete
• /
• 제7권2호
• /
• pp.169-190
• /
• 2010

The focus of this research effort was characterization of the flexural and tensile properties of a specific ultra-high-strength, fiber-reinforced concrete material. The material exhibited a mean unconfined compressive strength of approximately 140 MPa and was reinforced with short, randomly distributed alkali resistant glass fibers. As a part of the study, coupled experimental, analytical and numerical investigations were performed. Flexural and direct tension tests were first conducted to experimentally characterize material behavior. Following experimentation, a micromechanically-based analytical model was utilized to calculate the material's tensile failure response, which was compared to the experimental results. Lastly, to investigate the relationship between the tensile failure and flexural response, a numerical analysis of the flexural experiments was performed utilizing the experimentally developed tensile failure function. Results of the experimental, analytical and numerical investigations are presented herein.

• 대한기계학회논문집A
• /
• 제33권4호
• /
• pp.360-365
• /
• 2009

In the manufacture of CFRP(Carbon Fiber Reinforced Polymer Composite) composite structures, various independent components join by bolts and pins. Holes for bolts and pins have an effect on the failure strength of such structures, because those act as notches in structures. The failure characteristic of such structures are different from those of plain plate subject to remote load. In this paper, tensile properties of woven CFRP composite plates with laminates of $0^{\circ}$, $30^{\circ}$ and $45^{\circ}$ were obtained according to ASTM D 3039. By using obtained tensile failure strength and Tan-Cheng failure criterion, tensile failure strength of CFRP laminate with arbitrary fiber angle were evaluated. Also, the degradation of tensile properties by center hole(${\phi}10mm$) with a remote load was evaluated and the failure strengths were applied to Tan's failure criterion, similarly.

• 비파괴검사학회지
• /
• 제30권2호
• /
• pp.116-120
• /
• 2010

차축과 차륜으로 구성되는 철도차량 윤축은 차량의 운행과 관련하여 안전과 직결되는 중요한 철도 부품의 하나이다. 본 연구에서는 철도차량의 차축 재료의 인장파괴거동에 대한 특성을 분석하였다. 20년 이상 운행된 전기기관차 및 디젤전기기관차의 차축 시편에 대하여 연장시험을 수행하였다. 인장시험 동안 시편의 파괴특성을 모니터링하기 위해 고속 적외선카메라가 사용되었는데, 인장시험 동안의 시편 표변의 온도 변화를 모니터링하여 온도 분포로부터 인장파괴거동을 설명하고 파괴모드를 규명하고자 하였다.

• 한국철도학회논문집
• /
• 제11권3호
• /
• pp.280-285
• /
• 2008

Gurson model과 shear failure model 두 가지 파괴모델을 이용하여 노치인장시험과 초기 균열을 가지는 파쇄튜브의 압축거동을 유한요소법으로 해석하였다. Shear failure model의 파라미터 값은 노치인장시편의 시험 및 해석을 통하여 결정하였다. 항복강도와 파괴전단변형률 등의 파라미터 값을 정한 후, Gurson model과 shear failure model을 파쇄튜브의 해석에 적용하였다. Gurson model과 shear failure model이 인장시편에 대하여는 비슷한 파괴 거동을 보여주지만 파쇄튜브의 압축력과 균열 성장 속도에서는 다른 결과를 보임을 확인하였다. 즉, shear failure model에서는 Gurson model에 비하여 균열이 전파되기 위해 더 큰 압축력이 요구되었다. 이러한 현상은 shear failure model 이 재질의 손상 과정에 대한 고려를 포함하고 있지 않기 때문인 것으로 생각된다. 어느 모델이 튜브의 해석에 적당한 지를 실험을 통하여 검증할 필요가 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제31권5호
• /
• pp.96-103
• /
• 2003

국산 주요 침엽수재인 소나무, 잣나무, 낙엽송의 철물접합부 인장하중 특성 구명을 위하여 본 연구를 수행하였다. 철물 접합부의 최대 인장하중은 AA형의 경우 소나무가 3,612 kgf로 낙엽송, 잣나무에 비해 각각 1.2배, 1.7배, EA형의 경우 2,704 kgf로 1.1배, 1.5배 우수하였다. 또한 AA형은 EA형에 비해 3 수종 모두 약 1.2배 이상 높은 인장하중을 나타내었다. 철물접합부의 파괴모드는 주로 이의 빠짐, 철물의 인장파괴와 목재의 전단파괴로 이루어지며, 특히 소나무 접합부는 철물의 인장파괴를 나타내었다. 철물접합부재의 인장하중-변위 특성은 Foschi 모형으로 정확하게 추정할 수 있었으며, 철물접합부의 초기강성은 소나무 접합부재가 높게 나타났다. 국산 침엽수재의 철물접합부에 대한 설계하중은 소나무, 낙엽송, 잣나무의 순으로 높게 나타났으며, AA형의 경우 이당 설계하중이 소나무 25 kgf, 낙엽송 22 kgf, 잣나무 15 kgf이었으며, EA형의 경우 소나무 19 kgf, 낙엽송 17 kgf, 잣나무 13 kgf 이었다.