• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.1
• /
• pp.14-21
• /
• 2012

The effects of cutting condition and tempering temperature for the shape of cutting chip were investigated. For this purpose, a lead-free brass containing 1wt.% of Bi extruded at $750^{\circ}C$ in straight turning was used in this study. The cutting chip preferred was mainly found to be loose form of arc chips with curling discontinuity, and these were formed by shear fracture. However, some of fragmental element chip were found to be mixed when tempering temperature was as high as $500^{\circ}C$. The form and size of chip was more affected by feed rate than by tempering temperature and cutting rate. In addition, the cutting surface was observed to be formed more rough in the case of high feed rate and low cutting rate compared to low feed rate and high cutting rate.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.1
• /
• pp.7-14
• /
• 2023

We investigated the effect of multiple tempering on the microstructure and mechanical properties of AISI 4340 steel. The austenitized and quenched AISI 4340 steels were tempered at 550, 600, and 650℃ for 1, 2, and 4 h by single-tempering (ST). The multiple tempering was conducted for 4 h by double-tempering (DT, 2 h + 2 h), and quadruple-tempering (QT, 1 h + 1 h + 1 h + 1 h). As tempering temperature increases, yield strength and ultimate tensile strength decrease and elongation increases due to recovery and recrystallization of martensite and coarsening of carbides. At 550℃, as the number of tempering cycles increases, the yield strength and tensile strength decrease at the expense of fracture elongation. At 600 and 650℃, the yield strength and tensile strength increase with increasing the number of tempering cycles while fracture elongation maintains similar values. The multiple tempering at the same tempering time of 4 h improves the modulus of toughness at all tempering temperatures, which is presumed to be due to the change in carbide precipitation behavior by multiple tempering.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.10
• /
• pp.69-74
• /
• 2009

The tempering system which is developed by this research which sees energy curtailment and from the environmental side which is essential for in hazard analysis critical control point. The tempering system with development experimented frozen pork and fish. As test result, frozen pork region was not thawed occurred plentifully. Like this the actual condition, the case of frozen fish is grind and the bulk and density uniformly was formed, the pork the density was dense and was thought with the fact that the temperature difference change is big. Also after tempering from measurement location center the temperature appeared substitutionally with the low-end thing. This central part of the frozene region is thought the impedance change appears few. To hereafter respects an impedance change is thought that has the necessity which will change the structure of tempering system.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.3
• /
• pp.120-125
• /
• 2013

In this study, the effect of tempering treatment on the mechanical properties in modified 440A steel has been investigated. The amount of remaining carbide decreased with increasing the austenitizing treatment temperature, and all carbides were completely dissolved at $1250^{\circ}C$. The amount of remaining carbide decreased with increasing the time of austenitizing, but the carbide remained insoluble up to 120 minutes at $1050^{\circ}C$. With increasing the tempering temperature, tensile strength decreased, and elongation increased slowly, while hardness rapidly decreased, and impact value unchanged and then rapidly increased over $500^{\circ}C$. The strength and hardness slowly decreased, while the elongation and impact absorbed energy increased with increasing the tempering time. $Cr_{23}C_6$ type carbide was precipitated and sharp decrease of elongation and toughness by tempering did not appear.

• Journal of Power System Engineering
• /
• v.15 no.2
• /
• pp.42-48
• /
• 2011

440A martensitic stainless steels which were modified with reduced carbon content(~0.5%) and addition of small amount of nickel, vanadium, tungsten and molybdenum were manufactured. Effects of alloying elements and tempering temperatures on the uniform corrosion in the solution of lN H2S04 were investigated through the electrochemical polarization test. When tempering temperature is constant, corrosion current density in active-passive transition point, Icorr, decreased a little with an increase of austenitizing temperature. In addition to this, when austenitizing temperature is constant, longer holding time showed a little lower Icorr and Ipass, passive current density. And when austenitized at $1050^{\circ}C$ and tempered in a range of $350{\sim}750^{\circ}C$, best anti-corrosion properties were obtained at $350^{\circ}C$ tempering temperature while worst at $450^{\circ}C$ or $550^{\circ}C$. The specimens tempered at below $450^{\circ}C$ and above $550^{\circ}C$, similar and good anti-corrosion characteristics were obtained regardless of alloying elements added, showing anti-corrosion characteristics are influenced more by tempering temperature than by alloying elements.

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.2
• /
• pp.10-19
• /
• 1990

The tempering behavoirs of 0.45% carbon steel treated by automatic progressive high frequency induction hardening equipment have been investigated. In order to examine the correlation of hardness with both tempering temperature and time, simple regression analysis has been made using the statistical quality control package. The maximum surface hardness value of induction hardened zone and its effective hardening depth have been determined to be Hv 810 and 0.76mm, respectively. The hardness obtained after tempering has been shown to vary lineary with tempering time at six different temperatures. The activation energies during tempering have been calculated to be 25.34kcal/mole, 32.73kcal/mole and 49.24kcal/mole for HRcs 60, 50 and 40, respectively, showing that tempering process occurs by a complex mechanism, The tempering hardness equation of $H=90.113{\sim}4.531{\times}10^{-3}$ [T(11.996+log t)] has proved to be in a reasonably good agreement with experimently determined data and it is also expected to be useful for the determination of tempering treatment conditions to obtain a required hardness value.

• Journal of Welding and Joining
• /
• v.28 no.5
• /
• pp.51-57
• /
• 2010

Brittle microstructure created in a heat affected zone (HAZ) during the welding of low alloy steel can be eliminated by post-weld heat treatment (PWHT). If the PWHT is not possible during a repair welding, the controlled bead depositions of multi-pass welding should be applied to obtain tempering effect on the HAZ without PWHT. In order to anticipate and control the tempering effect during the temper bead welding, the definition of temperature curve obtained from the analytical solution was suggested in this research. Because the analytical solution for heat flow is expressed as a mathematical equation of weld parameters, it may be effective in anticipating the effect of each weld parameter on the tempering in HAZ during the successive bead depositions. The reheating effect by the successive bead layer on the brittle coarse grained HAZ formed by earlier bead deposition was estimated by comparing the overlapped distance between the temperature curves in the HAZ. Three layered weld specimens of SA508 base metal with A52 filler were prepared by controlling heat input ratio between layers. The tempering effect anticipated by using the overlapped distance between the temperature curves was verified by measuring the micro-hardness distribution in the HAZ of prepared specimens. The temperature curve obtained from analytical solution was expected as a good tool to find optimal temper bead welding conditions.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.29-36
• /
• 2016

Aluminum alloys have been widely used in engine materials, cold & hot-water storage vessels and piping etc., Furthermore, the aluminum alloy of AC8A have been widely used in mold casting material of engine piston for various vehicles because of its properties of temperature, wear and corrosion resistance. Therefore, it is considered that evaluation of corrosion resistance as well as wear resistance of AC8A material is also important to improve its property and to prolong its lifetime. In previous paper, the effect of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 16, 24, and 36 hrs)heat treatments to corrosion resistance and hardness were investigated using electrochemical method. In this study, in order to examine completely the effect of the tempering hours to hardness variation and corrosion resistance, the results of solution($510^{\circ}C$:4hrs) and tempering($190^{\circ}C$: 2, 4, 8 and 12hrs)heat treatments to hardness and corrosion resistance were investigated using electrochemical method. The hardness decreased with solution heat treatment compared to mold casting condition, but its value increased with tempering heat treatment. Furthermore, the corrosion resistance increased with decreasing of the hardness, and decreased with increasing of the hardness reversely. And the tempering heat treatment temperature at $190^{\circ}C$ for 8 hrs exhibited the highest value of the hardness and also indicated the highest corrosion current density. However, the values of hardness and corrosion current density was again increasingly decreased with increasing of tempering hours than 8 hrs, Consequently, it is suggested that decision of the optimum. tempering hours is very important to improve the corrosion or wear resistance.

• Journal of Power System Engineering
• /
• v.15 no.2
• /
• pp.49-54
• /
• 2011

Effect of tempering treatment on the mechanical properties of 12Cr heat resistant steel with ferrite phase was investigate in this study. As time and temperature of tempering treatment were increase, C and Cr contents in matrix structure were decreased. Due to increase of the amount of Cr26C6 type carbides. It was confirmed in mechanical properties experimental that tensile strength and hardness were decreased, while elongation and impact value were, increased with increasing the time and temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.38-39
• /
• 2009

The precipitate percentage and the spheroidization percentage were analyzed as a function of the tempering temperatures and the alloying elements for high strength preheat-treated steel. The optimum temperature of tempering produced the small precipitates of nano size. The precipitate percentage and the spheroidization percentage were increased with the tempering temperatures. The size of precipitate decreased as the spheroidization of carbon precipitates progressed. The alloying elements such as Cr and Mo reduced the sphereidization temperature.