• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.477-485
• /
• 1999

The grafting of 2,3-epoxypropylmethacrylate (GMA) onto polypropylene fabric was carried out by the $\gamma$-ray preirradiation grafting technique. Subsequently, the GMA-grafted polypropylene fabric was reacted with iminodiacetic acid (IDA) in different mixed solvents to prepare the fibrous metal adsorbent. The grafting extent was found to be dependent on the reaction time, temperature, preirradiation dose and dose rate. The effects of various mixed solvents on the IDA amination onto GMA-grafted polypropylene fabric were investigated. Compared with other mixed solvents, the extent of amination was highest in the dimethylsulfoxide (DMSO)/water, but the reaction did not occur in the water. The adsorption characteristics of various metal ions by the prepared adsorbent were examined when it was immersed in the 100 ppm metal ion solution. The amount of adsorption followed the order:$Pb^{2+}>Co^{2+}>Fe^{2+}$.

• Journal of the Korean Society for Railway
• /
• v.13 no.6
• /
• pp.552-558
• /
• 2010

Ride comfort of railway vehicles is affected by many factors, such as vibration, noise, smell, temperature, visual stimuli, humidity and a seat design. In general, vibration, which originates from vehicle motion, is considered as the primary concern. In evaluating the ride comfort, relationship between passenger's feeling and vibration characteristics is very important because human feeling is dependent on frequency spectrum of vibration. Therefore, the weighing functions in frequency domain are used to evaluate the ride comfort of railway vehicles. In the present paper, we have analyzed the characteristics of the frequency weighting curves defined in many standards and reviewed the effect resulting from their difference on the ride comfort.

• Corrosion Science and Technology
• /
• v.19 no.4
• /
• pp.203-210
• /
• 2020

The corrosion behavior of super austenitic stainless steel was studied by examining the characteristics of the sigma phase formed in the steel. A range of experimental and analytical methods was employed, including potentiodynamic polarization tests, critical pitting temperature tests, transmission electron microscopy, and energy-dispersive spectroscopy. Three steel samples with different sigma phase levels were obtained by intentionally adjusting the manufacturing process. The results showed that the corrosion resistance of the samples was strongly dependent upon the size and distribution of the sigma phase precipitated in the samples. The larger the size of the sigma phase, the higher the Mo content in the sigma phase and the higher the depletion level of Mo at the interface between the matrix/sigma phase, the more samples with a coarse-sized sigma phase were susceptible to localized pitting corrosion at the interface. These results suggest that various manufacturing processes, such as welding and the post-heat treatment of the steel, should be optimized so that both the size and fraction of the sigma phase precipitated in the steel are small to improve the resistance to localized corrosion.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.492-497
• /
• 2001

We report the characteristics and the dependence of sputter-deposited Ta films on the process parameters. The properties of as-deposited Ta films such as deposition rate, resistivity, Rs uniformity, reflectivity, and stress were investigated and analyzed as a function of process parameter using a statistical experimental method. The functional relationships between the independent and dependent variables were predicted by surface response. The optimal deposition condition of DC magnetron sputtered Ta films was obtained at the chamber pressure of 2 mTorr, power density of 8 W/$\textrm{cm}^2$, and substrate temperature of 2$0^{\circ}C$ by means of resistivity and Rs uniformity. The fitness value for quadratic model as evaluated by the R- square was 0.85~ 0.9 without pooling. The as-deposited Ta films exhibited the resistivity of ~180$\mu$$\Omega$cm with Rs uniformity of ~2%. The transmission electron microscopy and x-ray diffractometry identified that the phase of as-deposited film was $\beta$-Ta having the grain size of 100~200.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.3
• /
• pp.431-437
• /
• 1998

In this paper, we have investigated the electrical properties of ultra-thin nitrided oxide(NO) and re-oxidized nitrided oxide(ONO) films that are considered to be promising candidates for replacing conventional silicon dioxide film in ULSI level integration. Especially, we have studied a variation of I-V characteristics, gate voltage shift, and time-dependent dielectric breakdown(TDDB) of thin layer NO and ONO film depending on nitridation and reoxidation time, respectively, and measured a variation of leakage current and charge-to-breakdown(Q$\_bd$) of optimized NO and ONO film depending on ambient temperature, and then compared with the properties of conventional SIO$\_2$. From the results, we find that these NO and ONO thin films are strongly influenced by process time and the optimized ONO film shows superior dielectric characteristics, and (Q$\_bd$) performance over the NO film and SIO$\_2$, while maintaining a similar electric field dependence compared with NO layer.

• Journal of Korea Water Resources Association
• /
• v.32 no.2
• /
• pp.153-162
• /
• 1999

In this study, mixing and dilution characteristics of vertical multijet discharged by multiport diffuser into stagnant water are investigated. The results obtained from the experiment of multiport diffuser performed in the three dimensional flume are as follows. As far as merging process of multiport diffuser is concerned, merging starts at about z/l = 3 although merging length is dependent upon stability condition and thereafter lateral temperature distribution becomes gradually uniform which is typical distribution of plane jet. Analyses of experimental data for minimum dilution show that characteristics of minimum dilution are described based on three regions which are jet region where momentum is dominated, intermediate region, and plume region where buoyancy is dominated. Minimum dilution coefficient in plume region of multiport diffuser obtained in this study is 15% higher than that of plane diffuser. This is because individual jet of multiport diffuser entrains more ambient water before merging is occurred, and therefore dilution increases.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.2
• /
• pp.85-91
• /
• 2016

The most important factor in the structural design of ships and offshore structures operating in arctic region is ice load, which results from ice-structure interaction during the ice collision process. The mechanical properties of ice related to strength and failure, however, show very complicated aspect varying with temperature, volume fraction of brine, grain size, strain rate and etc. So it is nearly impossible to establish a perfect material model of ice satisfying all the mechanical characteristics completely. Therefore, in general, ice collision analysis was carried out by relatively simple material models considering only specific aspects of mechanical characteristics of ice and it would be the most significant cause of inevitable errors in the analysis. Especially, it is well-known that the most distinctive mechanical property of ice is high dependency on strain rate. Ice shows brittle attribute in higher strain rate while it becomes ductile in lower strain rate range. In this study, the simulation method of ice collision to ship hull using the nonlinear dynamic FE analysis was dealt with. To consider the strain rate effects of ice during ice-structural interaction, strain rate dependent constitutive model in which yield stress and hardening behaviors vary with strain rate was adopted. To reduce the huge amount of computing time, the modeling range of ice and ship structure were restricted to the confined region of interest. Under the various scenario of ice-ship hull collision, the structural behavior of hull panels and failure modes of ice were examined by nonlinear FE analysis technique.

• The Korean Journal of Food And Nutrition
• /
• v.32 no.2
• /
• pp.89-97
• /
• 2019

In this paper, quality properties and antioxidant capacity of cooked black carrot has been studied. Five different cooking methods have been applied: microwave (45 sec), boiling ($100^{\circ}C$, 14 min), steaming ($100^{\circ}C$, 20 min), sous vide ($75^{\circ}C$, 80 min), sous-vide ($95^{\circ}C$, 30 min). The color value was slightly different (p<0.05), the boiling method was the highest in L-value and Sous vide $75^{\circ}C$ method was the lowest. The steaming method indicated the highest a-value at 5.50. The b-value was significantly different between the samples (p<0.05). The microwave method was the highest at 3.49 while the sous vide $95^{\circ}C$ method was the lowest at -0.34. No significant difference was observed between the samples when only the moisture content results were considered. The highest pH was observed in samples cooked using the boiling method. The softening (%) was higher when the cooking water was in contact with samples and it was dependent on the temperatures. In addition, this study shows that not only temperature but also cooking time and cooking media are very crucial in the preparation and cooking of black carrot to prevent the loss of the antioxidant compound. In conclusion, the comparison of the quality characteristics and antioxidant properties of black carrots indicated that the most appropriate cooking method is sous-vide method.

• Advances in nano research
• /
• v.15 no.1
• /
• pp.1-13
• /
• 2023

Ti₃C₂T_x MXene, a 2D material, is known to exhibit unique characteristics that are strongly dependent on surface termination groups. Here, we developed a novel annealing approach with Ca as a reducing agent to simultaneously remove F and O groups from the surface of multilayered MXene powder. Unlike H₂ annealing that removes F effectively but has difficulty in removing O, annealing with Ca effectively removed both O and F. X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy revealed that the proposed approach effectively removed F and O from the MXene powder. The results of O/N analyses showed that the O concentration decreased by 57.5% (from 2.66 to 1.13 wt%). In addition, XPS fitting showed that the volume fraction of metal oxides (TiO₂ and Al₂O₃) decreased, while surface termination groups (-O and -OH) were enhanced, which could increase the hydrophilic and adsorption properties of the MXene. These findings suggest that when F and O are removed from the MXene powder, the interlayer spacing of its lattice structure increases. The proposed treatment also resulted in an increase in the specific surface area (from 5.17 to 10.98 m²/g), with an increase in oxidation resistance temperature in air from ~436 to ~667 ℃. The benefits of this novel technology were verified by demonstrating the significantly improved cyclic charge-discharge characteristics of a lithium-ion battery with a Ca-treated MXene electrode.

• Journal of Korean Society for Quality Management
• /
• v.52 no.1
• /
• pp.43-56
• /
• 2024

Purpose: The injection molding process, crucial for plastic shaping, encounters difficulties in sustaining product quality when replacing injection machines. Variations in machine types and outputs between different production lines or factories increase the risk of quality deterioration. In response, the study aims to develop a system that optimally adjusts conditions during the replacement of injection machines linked to molds. Methods: Utilizing a dataset of 12 injection process variables and 52 corresponding sensor variables, a predictive model is crafted using Decision Tree, Random Forest, and XGBoost. Model evaluation is conducted using an 80% training data and a 20% test data split. The dependent variable, classified into five characteristics based on temperature and pressure, guides the prediction model. Bayesian optimization, integrated into the selected model, determines optimal values for process variables during the replacement of injection machines. The iterative convergence of sensor prediction values to the optimum range is visually confirmed, aligning them with the target range. Experimental results validate the proposed approach. Results: Post-experiment analysis indicates the superiority of the XGBoost model across all five characteristics, achieving a combined high performance of 0.81 and a Mean Absolute Error (MAE) of 0.77. The study introduces a method for optimizing initial conditions in the injection process during machine replacement, utilizing Bayesian optimization. This streamlined approach reduces both time and costs, thereby enhancing process efficiency. Conclusion: This research contributes practical insights to the optimization literature, offering valuable guidance for industries seeking streamlined and cost-effective methods for machine replacement in injection molding.