• Elastomers and Composites
• /
• 제19권1호
• /
• pp.13-31
• /
• 1984

The purposes of this dissertation are to demonstrate that DSC theromoanaytical methods of vulcanization can provide useful informations on the vulcanization characteristics of industrial formulations and also provides the potential basis for a rapid and complete method of sulfur and vulcanizing accelerator analysis for quality control. The influences of those factors such as heating rate, scan temperature, vucanizing accelerator's type and concentration upon vulcanization exotherm in NR and NBR compounds in the presence of vulcanizing accelerators such as TMTD,MBTS,DPG,TMTM,CBS, and MBT were evaluated by means of DSC. In order to examine the credibility in the DSC method, the same samples which were used for DSC method were studied to compare the DSC results with the ODR (Oscillating Disk Rheometer) data. The results obtained were as follows 1. In the DSC dynamic experiments, the observed enthalpy results from vulcanization depends upon the heating rate; In the range of 2 to $20^{\circ}C/min$ of heating rate, as the heating rate was increased the enthalpy change was also increased. However, over the heating rate of $30^{\circ}C/min$ it was observed that the enthalpy change was decreased as the heating rate was further increased. Without regard to the change of enthalpy, tremendous instantaneous heat evolving was observed in the range of high heating rates. 2. For the samples which are added with various vulcanizing accelerators, the activation energies of vulcanization were as follows; 3. Regarding to the influences of vulcanizining accelerator's types upon the characteristics of vulcanization exotherm, NR and NBR compounds in the presence of thiuramsulphide compounds type accelerators such as TMTD, TMTM, were exhibited sharper and higher vulclanization exotherm than others. From the resuts of DSC thermograms which was distributed in even shape in the broad temperature range, it was clearly shown that the guanidine compounds type accelerator such as DPG acts as a delayed acting accelerator. 4. In the comparison of DSC and ODR results, the dependency of temperature in the cure rate and the observed conversions show good agreements between two results. 5. In the same curatives, by the comparison of glass transition temperatures, it was possible to predict relative values of maximum torques. Consequently, from the present studies, it is shown that the DSC thermoanalytical method can provide an alternate new method for rapid and complete quality control analysis of rubber industry.

• 대한기계학회논문집A
• /
• 제39권1호
• /
• pp.37-43
• /
• 2015

압전소자(Piezoelectric transducer, PZT)는 구조물의 안정성 평가를 목적으로 하는 구조 건전성 모니터링 기법(Structural Health Monitoring, SHM)의 센서(sensor) 및 구동기(actuator)로 많이 활용되고 있다. 사용되는 센서 및 구동기의 성능을 사전에 파악하고, 잔존수명 및 결함을 탐지하는 센서 자가 진단법은 안정적인 SHM의 결과를 얻기 위해 매우 중요한 절차이다. 본 연구에서는 Admittance 값을 기반으로 한 센서 자가 진단절차를 통하여 압전체 센서의 결함을 탐지하였으며, 센서 진단과정에 영향을 줄 수 있는 접합층 및 온도 등의 영향인자에 대해 실험적 분석을 실시하였다. 분석 결과 Admittance와 온도 및 접착제의 상관관계를 파악할 수 있었으며, admittance를 기반으로 한 센서 자가 진단 절차를 통해 센서의 접착상태와 접착제의 성능평가가 가능함을 검증하였다.

• Structural Engineering and Mechanics
• /
• 제73권2호
• /
• pp.191-207
• /
• 2020

This study aims at investigating the size-dependent free vibration of porous nanoplates when exposed to hygrothermal environment and rested on Kerr foundation. Based on the modified power-law model, material properties of porous functionally graded (FG) nanoplates are supposed to change continuously along the thickness direction. The generalized nonlocal strain gradient elasticity theory incorporating three scale factors (i.e. lower- and higher-order nonlocal parameters, strain gradient length scale parameter), is employed to expand the assumption of second shear deformation theory (SSDT) for considering the small size effect on plates. The governing equations are obtained based on Hamilton's principle and then the equations are solved using an analytical method. The elastic Kerr foundation, as a highly effected foundation type, is adopted to capture the foundation effects. Three different patterns of porosity (namely, even, uneven and logarithmic-uneven porosities) are also considered to fill some gaps of porosity impact. A comparative study is given by using various structural models to show the effect of material composition, porosity distribution, temperature and moisture differences, size dependency and elastic Kerr foundation on the size-dependent free vibration of porous nanoplates. Results show a significant change in higher-order frequencies due to small scale parameters, which could be due to the size effect mechanisms. Furthermore, Porosities inside of the material properties often present a stiffness softening effect on the vibration frequency of FG nanoplates.

• Korean Chemical Engineering Research
• /
• 제49권5호
• /
• pp.560-564
• /
• 2011

본 연구의 목적은 과산화수소 농축을 위한 투과증발공정의 수학적 모델을 제시하는 것이다. 대상공정은 NASA에서 개발한 것으로 쉘과 멤브레인 튜브들로 구성되어 있다. 쉘과 튜브에는 각각 과산화수소용액과 sweep gas가 향류로 흐른다. 이때 막을 통해 투과증발되는 기체에는 과산화수소보다 물분자가 더 많기 때문에 과산화수소를 농축할 수 있다. 이 공정의 수학적 모델은 투과물의 흡수-확산 메커니즘에 기초한 비선형 편미분 및 대수 방정식, 투과물 플럭스의 온도 의존성에 대한 아레니우스 관계, 그리고 막 모듈 내의 액상 농도와 흐름에 대한 질량 및 운동량 수지식의 형태로 개발하였다. 과산화수소 농축물 농도의 동적 거동은 제안된 모델의 단순화된 형태를 풀어 모사하였고 그 결과값을 NASA 특허에서 보고된 실험자료와 비교하였다.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.460-467
• /
• 2016

Magnetic hyperthermia mediated by superparamagnetic particles is mainly based in sinusoidal waveforms as excitation signals. Temperature changes are conventionally explained by rotation of the particles in the surrounding medium. This is a hypothesis quite questionable since habitual experimental setups only produce changes in the magnetic module, not in the field lines trajectories. Theoretical results were tested by changing the waveform of the exciting signal in order to compare non-sinusoidal signals against sinusoidal signals. Experiments were done at different frequencies: 200 KHz, 400 KHz, 600 KHz, 800 KHz and 1 MHz. Superparamagnetic Iron Oxide samples (SPION), made of magnetite ($Fe_3O_4$) and suspended in water (100 mg/ml), were used. Magnetic field strength varies from $0.1{\pm}0.015KA/m$ to $0.6{\pm}0.015KA/m$. In this study was observed that the power loss depends on the applied frequency: for 1 to 2.5 RMS current the responses for each signal are part of the higher section of the exponential function, and for 3.5 to 8 RMS current the response is clearly the decrement exponential function's tale (under $1{\times}10^3LER/gr$).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.58-58
• /
• 2009

Uniformity related issues in chemical mechanical polishing (CMP) are within wafer non-uniformity (WIWNU), wafer to wafer non-uniformity (WTWNU), planarity and dishing/erosion. Here, the WIWNU that originates from spatial distribution of independent variables such as temperature, sliding distance, down force and material removal rate (MRR) during CMP, relies to spatial dependency. Among various sources of spatial irregularity, hardness and modulus of pad and surface roughness in sources for pad uniformity are great, especially. So, we investigated the spatial variation of pad surface characteristics using pad measuring system (PMS) and roughness measuring system. Reduced peak height ($R_{pk}$) of roughness parameter shows a strong correlation with the removal rate, and the distribution of relative sliding distance onwafer during polishing has an effect on the variation of $R_{pk}$ and WIWNU. Also, the results of pad wear profile thorough developed pad profiler well coincides with the kinematical simulation of conditioning, and it can contribute for the enhancement of WIWNU in CMP process.

• 방사성폐기물학회지
• /
• 제5권2호
• /
• pp.145-154
• /
• 2007

벤토나이트 완충재의 열수거동 실험에서는 고준위폐기물처분장 완충재로 유력하게 고려되고 있는 국산 벤토나이트를 대상으로 열수특성을 규명하고, 또 그 결과를 바탕으로 KRS 처분환경에서 벤토나이트 완충재의 장기건전성을 평가하였다. 실험결과, 벤토나이트 완충재의 열수반응은 주 구성광물인 스멕타이트의 일라이트화를 통해 진행되었으며, 온도, $K^+$농도, pH는 이러한 일라이트화에 중요한 열수반응인자 역할을 하였다. KRS 처분환경에 대한 국산벤토나이트 완충재의 장기건전성을 분석한 결과, 정상상태에서는 벤토나이트 완충재가 오랜 기간 동안 방벽재기능을 유지하였지만, 보수적인 조건에서는 약 $5{\times}10^4$년이 경과했을 때 벤토나이트 완충재를 구성하는 스멕타이트의 50%이상이 일라이트로 전환되어 방벽재로서의 팽윤능력을 상실할 수 있음을 예상할 수 있었다.

• 한국의학물리학회지:의학물리
• /
• 제6권1호
• /
• pp.49-57
• /
• 1995

반도체검출기는 소형 및 방사선에 고감도특성을 갖고 있으나, 고에너지 광자선 및 전자선등의 조사에 의해 손상을 입어 감도저하를 초래하게 되며 계측시 선량재현성을 기대하기어려워진다. 실험대상은 P-형 실리콘 반도체검출기이며 선량율, 김출방향 및 온도 변화에 따른 선량특성이 조사되었고, 선량재현성을 높이기 위해 18 MeV 고에너지전자선으로 3KGy까지 전처리조사하고 광자선 및 전자선의 전처리조사선량에 대한 감도특성변화를 얻었다. 전처리조사가 작은 0.5KGy인 경우, 저선량율과 고선량율하의 단위선량당 감도는 약 35％의 차이를 보였으며 .3KGy인 경우 약 20％의 차이를 보여 전처리선량이 클 수록 감도차는 작아짐을 알수 있다. 실리콘 반도체검출기의 검출방향성은 임의의 조사각에서 최저치와 최대치의 선량차가 약 13％를 나타내었으며, 검출기의 온도의존성은 4도에서 35도까지 거의 선형성을 보였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권3호
• /
• pp.37-40
• /
• 2015

Recently, the electrical insulation design for electrical apparatuses is important to cope with the tendency of high voltage. The degradation characteristics of a superconducting coil due to an electrical breakdown should be considered to design a high voltage superconducting coil. In this paper, the degradation characteristics of 2G high temperature superconducting (HTS) wires are studied with respect to electrical breakdown tests. To analyze the dependency of the degradation characteristics of 2G HTS wires, the electrical breakdown tests are performed with AC(alternating current) and DC(direct current) voltage. All tests are performed by applying various magnitudes of AC and DC breakdown voltages. To verify the degradation characteristics of 2G HTS wires, the tests are performed with various 2G HTS wires with respect to stabilizer materials. The degradation characteristics of 2G HTS wires, such as Ic(critical current) and index number are measured by performing electrical breakdown tests. It is found that the characteristics such as Ic and index number can be degraded by an electrical breakdown. Moreover, it is concluded that the degradation characteristics of 2G HTS wires are affected by the stabilizer material and applied voltages. The cross-sectional view of 2G HTS wires is observed by using a scanning electron microscope (SEM). As results, it is found that the degradation characteristics of 2G HTS wires are concerned with hardness and electrical conductivity of stabilizer layers.

• 전자공학회논문지D
• /
• 제36D권6호
• /
• pp.44-51
• /
• 1999

High density DRAM의 cell capacitor로 촉망 받고 있는 고유전체 BST박막 커패시터의 저 전계(<0.2MV/cm) 영역에서의 전기전도 현상을 분석하였다. 저 전계 영역에서 Pt/BST/Pt구조의 MIM 커패시터에 일정 전계를 인가한 후 전류를 측정하는 I(t)방법을 이용하여 유전완화전류와 누설전류를 분리해내어 박막의 측정온도 변화, 전계의 크기, 인가방향 변화, 후속 열처리에 따른 BST 박막의 전기전도 기구를 분석하였다. 그 결과, 유전완화전류는 Hoppiong process에 의한 BST박막내부의 trap된 전자들의 이동에 의한 전하재배치로 설명되어지며, 누설전류도 박막내의 trap에 의한 poole-Frenkel process에 의한 것임을 알 수 있었다. 그리고 각 전류성분에 기억하고 있는 trap이 BST박막내의 산호 결핍임을 추정하였다.