• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.199-200
• /
• 2019

The purpose of the research is assessing the possibility of strength recovery for mortar added with accidently high amount of fly ash. For compressive strength at 28 day, the sample painted with sodium hydroxide showed higher compressive strength than the sample painted with calcium hydroxide. Regarding the curing conditions, the curing temperature 65℃ provided better conditions than the curing temperature 20℃ in aspect of solution penetration depth and reactivity of fly ash. In the case of drying after saturation, the case painted with sodium hydroxid 65℃ showed the clearest engrossing mark.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 추계 학술논문 발표대회
• /
• pp.107-110
• /
• 2009

After inquiring into physical characteristics of using fly ash and alkali solution, it was found that higher pH density is favorable to strength development at early age and the higher the age is, the higher the compressive strength gets. Also, it was found that when there is more addition of activator, the compressive strength is higher. I was shown that more than atmospheric curing, steam curing was favorable for development of compressive strength. When the temperature of curing temperature was higher, most of the compressive strengths were higher. Thus, based on this study, it was understood that environmental-friendly chemically combined concrete using fly ash and alkali solution can be utilized without using cement.

• Advances in concrete construction
• /
• 제5권5호
• /
• pp.481-492
• /
• 2017

The aim of this paper is to investigate the effect of quartz powder (Qp), quartz sand (Qs), and different water curing temperature on mechanical properties including 7, 14, 28-day compressive strength and 28-day splitting tensile strength of Ultra High Performance Concrete and also finding the correlation between these variables on mechanical properties of UHPC. The response surface methodology was monitored to show the influences of variables and their interactions on mechanical properties of UHPC, then, mathematical models in terms of coded variables were established by ANOVA. The offered models are valid for the variables between: quartz powder 0 to 20% of cement substitution by cement weight, quartz sand 0 to 50% of aggregate substitution by crushed limestone weight, and water curing temperature 25 to $95^{\circ}C$.

• 한국인쇄학회지
• /
• 제18권1호
• /
• pp.157-166
• /
• 2000

UV-curable resins have adventages of quick set, space saving, clean environment, and efficient use of energy. The polymerization induced phase separation has been studied to solve the problem in UV-curing of thick films and develop the new functional materials. On the exposure to UV irradiation, the dynamic elasticity properties were mesured for mixtures of alkyd resin and UV-cruable monomers which have different molecular structures and molecular weights. The curing rate increases with increasing temperature and UV intensity. In addition, The gel point is strongly influenced by temperature and UV intensity

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.532-533
• /
• 2006

In this research work attempts were made to study the bonding of thermoplastics with adhesives using solar energy. In order to study the curing behaviour necessary experiments were conducted under varying conditions of temperature, exposure time and power. The cured samples were then studied under the optical microscope before subjecting to tensile testing in order to study their mechanical properties. The fracture surfaces were further studied under the Scanning Electron Microscopy in order to study the microstructural changes that are taken place during curing. From the present study it is evident that curing under higher solar energy temperature, generally improves bond strength and quality of the adhesive joints when compared to other modes of curing process expect the microwave curing process.

• 한국정밀공학회지
• /
• 제31권8호
• /
• pp.653-658
• /
• 2014

Roll-to-Roll printing process has become a great issue as a breakthrough for low cost and mass production of electronic devices such as organic thin film transistor, and etc. To print the electronic devices, multi-layer printing is essential, and high precision register control is required for this process. Unlike stop-and-repeat printing process, it is impossible to control the register in a static state since the roll-to-roll process is a continuous system. Therefore, the behavior of web such as polyethylene terephthalate (PET) and polyimide (PI) by the tensile and thermal stress generated in the roll-to-roll process as well as motor control of driven rolls has to be considered for a high precision register control. In this study, the correlation between curing temperature and thermal deformation of PET web is analyzed. Finally, it is verified experimentally that the temperature disturbance generates the more serious register error under the higher curing temperature.

• 한국건축시공학회지
• /
• 제3권2호
• /
• pp.135-139
• /
• 2003

The purpose of this study is to analyze the curing effect of planar surface heater for concreting in cold weather. Some experiments were conducted to evaluate the temperature history of concrete cured with heating sheets in the laboratory conditions. As the results, It was showed that the 130W/$m^2$-heater could raise the inner temperature more than $20^{\circ}C$ under the environmental condition of -5~$-20^{\circ}C$. And the temperature of concrete cured by the 200W/$m^2$-heater was 5~$10^{\circ}C$ higher than that of concrete cured by 130W/$m^2$-heater. Finally, through the curing by the planar surface heater during the first 1.5~2 days, it is possible to secure the sufficient maturity of concrete.

• 대한건축학회논문집:구조계
• /
• 제34권5호
• /
• pp.27-34
• /
• 2018

Concrete placed under hot weather condition suffers from larger slump loss, rapid moisture evaporation due to high air temperature. Proper measures for material, transportation and curing should be taken to prevent the quality deterioration of the concrete under hot weather condition. In Korea, Although the period of hot weather concrete in Korea occupies only 2 months, there are a lot of quality problems including plastic, drying shrinkage and cold joint. Therefore, the objective of this paper is to investigate and compare the temperature history and crack occurrence of the concrete, which was placed in the actual apartment house construction field under hot weather condition, in response to the application of surface covered curing blankets including PE film, single layer clear bubble sheet, white colored bubble sheet and aluminum metalized bubble sheet. Test results indicated that the application of white colored bubble sheet and aluminum metalized bubble sheet showed most favorable results in terms of reduction in temperature rise and crack occurrence as well as easiness in handling. But, due to light reflection by aluminum metalized bubble sheet, it is believed that white colored bubble sheet is preferable.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.273-276
• /
• 2004

Recently. cold weather constructions were popularized because of the importance of construction term. The special method about mix design and curing of concrete was being planned to conduct cold weather constructions, but these method were not considered in a low temperature time. A Strength revelation of concrete is delayed in a curing condition of low temperature. If a construction was loaded in this case, cracks or remaining deformations are generated in a construction. So, a strength revelation characteristic in early age was investigated to secure early strength of concrete in curing condition of a low temperature. In this study, the method about concrete mix design was presented to secure construction safety in a low temperature time.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.808-811
• /
• 2000

The product of stereolithography is consist of gathering the single strand. Therefore the accuracy of the shape is related to the linear shrinkage of the single strand. The resin temperature change affect on curing properties. This article will propose the interaction between material temperature and shape accuracy by resin temperature control. The main concern of this article is related to the improvement of end product's shape accuracy by the persuit for the filles curing criterion.