• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.767-777
• /
• 2002

In this work, biodegradable modified aliphatic polyester (MAP) in tetrafunctional epoxy (4EP) resin was investigated in terms of cure kinetics, thermal stabilities, rheological properties, and mechanical interfacial properties. DSC results of the blends show that the cure activation energies (E$\_$a/) were increased in 10 wt% of MAP compared with neat 4EP, due to the increasing intermolecular interaction between 4EP and MAP. The decomposed activation energies (E$\_$t/) derived from Coats-Redfern method, were increased within the 10∼30 wt% composition range of MAP contents, resulting from increasing the cross-linking density of the blend system. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. Cross-linking activation energies (E$\_$c/) were determined from the Arrhenius equation based on gel time and curing temperature. As a result, the E$\_$c/ showed a similar behavior with E$\_$a/. The fracture toughness (K$\_$IC/) of the mechanical interfacial properties was discussed in semi-IPN behaviors of the casting specimen.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.4
• /
• pp.3545-3554
• /
• 1974

The objective of this study was to investigate the characteristics of the evaporation rate, the plastic shrinkage and the compressive strength of concrete exposed to a rapid evaporation environment immediately after casting. Drying of concrete were conducted under a controlled chamber in which the temperature was mainfoimed at 30 ${\pm}$1$^{\circ}C$, the relative humidity 22 ${\pm}$1 percent, and the wind velocity 7 ${\pm}$1 m/sec. The compressive strength of concrete was tested after 28 days of standard curing. The results obtained are as follows: 1. The evaporation rate was the highest at the very beginning, was decreased as the drying progresses, and was kept almost constant after 6 hours. 2. The shrinkage of concrete was changed in three different rates for the concrete mixture having its slump vallue between 3.0cm and 7.5cm. 3. The plastic shrinkage was ended within 5 or 6 hours after casting, regardless of the water cement ratio. 4. The shrinkage was increased within the limit of slump values between 3.0cm and 7.5cm as the water-cement ratio was increased. 5. The evaporation was kept on even after the plastic shrinkage was ended. 6. Within the limit of good workability (slump value between 4.5cm and 7.5cm), the compressive strength of concrete was increased when the shrinkage rate was slow but it was decreased when the rate was rapid 7. From the result of this study it is recommended that (1) the water-cement ratio should be less as long as the workability of concrete is allowable; (2) the evaporation should be prevented at least for 4 hours after casting concrete.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.2
• /
• pp.205-210
• /
• 2013

Thiol-ene polymerization is a versatile tool for several applications. Here we report the preparation of epoxide groups containing thiol-ene photocurable polymeric support and the covalent immobilization of ${\alpha}$-amylase onto these polymeric materials. The morphology of the polymeric support was characterized by scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) coupled with SEM was used to explore the chemical composition. The polymeric support and the immobilization of the enzyme were characterized by FTIR analysis. SEM-EDS and FTIR results showed that the enzyme was successfully covalently attached to the polymeric support. The immobilization efficiency and enzyme activity of ${\alpha}$-amylase were examined at various pH (5.0-8.0) and temperature ($30-80^{\circ}C$) values. The storage stability and reusability of immobilized ${\alpha}$-amylase were investigated. The immobilization yield was $276{\pm}1.6$ mg per gram of polymeric support. Enzyme assays demonstrated that the immobilized enzyme exhibited better thermostability than the free one. The storage stability and reusability were improved by the immobilization on this enzyme support. Free enzyme lost its activity completely within 15 days. On the other hand, the immobilized enzyme retained 86.7% of its activity after 30 days. These results confirm that ${\alpha}$-amylase was successfully immobilized and gained a more stable character compared with the free one.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.16 no.2
• /
• pp.68-74
• /
• 1983

A moderately halophilic bacterium, Listeria denitrificans HB-38, isolated from mud on the seashore in Sooyoung bay, Pusan, showed the requirement of $4\%$ sodium chloride for cell growth in a medium with salts typical of a marine environment, and showed that of $10\%$ in a medium with salts typical of a terrestrial environment. The optimum temperature and pH for growth were $40^{circ}C$ and pH 7.5 in the medium containing $10\%$ sodium chloride and ions typical of a terrestrial environment. Sodium chloride as a protoplast stabilizer gave more stability than sorbitol or sucrose, meanwhile the protoplast did not require higher concentration of stabilizer than that of E. coli protoplast. Succinic dehydrogenase of HB-38 had a halophilic property showing maximal activity in the presence of $9\%$ sodium chloride. The strain HB-38 did not harbor an extrach-romosomal DNA.

• Journal of Adhesion and Interface
• /
• v.20 no.4
• /
• pp.146-154
• /
• 2019

In this study, alkoxysilane-functionalized amphiphilic polymer (AFAP), which have hydrophilic segment and hydrophobic segment functionalized by alkoxysilane group at the same backbone, was synthesized and used as a dispersant and control agent for reaction rate in the preparation of colloidally stable organic-inorganic (O-I) hybrid sols. After reaction with fluorosilane compounds, fluorinated O-I hybrid sols were prepared and coated onto glass substrate to form hydrophobic O-I hybrid coating films through low-temperature curing process. Surface hardness and hydrophobicity of cured coating films were varied with type of solvent and composition of AFAP and fluorinated alkoxysilane compounds. At appropriate solvent and composition of fluorinated alkoxysilane compounds, O-I hybrid coating film having high transparency and surface hardness could be prepared, which could be applicable to cover window of solar cell and displays.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.231-237
• /
• 2012

This study measured the mechanical and damping properties of EPDM compounds including fillers. Semi-reinforcing furnace black (SRF), high abrasion furnace black (HAF) and acetylene black were used as fillers. Dicumyl peroxide (DCP) were used as curing agents. The measurements were conducted using a moving die rheometer (MDR), durometer, universal testing machine (UTM), compression set and dynamic mechanical analysis (DMA). The tensile strength and elongation at break increased with increasing SRF contents in EPDM compounds. However, they decreased with increasing the amount of acetylene black. In the inspecting temperature range, EPDM compound filled acetylene black had stable storage modulus. Furthermore, the tan ${\delta}$ of the EPDM compounds obtained was enhanced by compounding with acetylene black.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.1
• /
• pp.1-5
• /
• 2015

For the special usage, the effort of developing AlN single crystals has been very hot in the world. The AlN-base UV LEDs are used on the field of sterilization, purification, curing and analyzing, which can advance human's living and medical processes etc.. AlN single crystals were grown by the PVT (Physical vapor transport) method. On the growing process, carbon crucibles with three different types such as normal size, taller than normal and wider than normal were used for comparison. The processing temperature was in the range of $1900{\sim}2100^{\circ}C$ and ambient pressure was 200~1 Torr. When the taller crucible was used, the sublimation mass was greater than normal dimension one but the best condition of growth changes widely. However the wider one gave much sublimation mass and growing condition was more stable than normal dimension. On limited growing furnace system, the changes of crucible dimension of PVT method provide the change of best condition for growth rate, as-grown crystal quality and growth condition stability.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.637-640
• /
• 2008

Since the first underground LNG tank was constructed in Incheon, continuously many LNG tanks were constructed in Tongyoung and Pyongtaek. The storage capacity of LNG tank increased by 200,000kl and the structure size and the concrete mixing design has changed. The crack of concrete induced by the heat of hydration is a serious problem, particularly in massive concrete structures. In order to control the thermal crack of massive concrete, the low heat portland cement(type Ⅳ) is applied to bottom annular part, bottom central part, lower walls and ring beam. In this study, in order to thermal crack control about the LNG tank wall(lot 8 of #16 Pyongtaek LNG tank) in winter, analysed the concrete temperature, the extention of term, the curing condition and the concrete mixing design. When the concrete mixing design is changed from OPC+FA25% to LHC+FA25%, the thermal crack index is 1.33 and satisfied with construction specifications(over 1.2).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.441-444
• /
• 2008

Ultra high performance concrete (UHPC) in this study is composed of sand, cement, silica fume, siliceous powder, superplasticizer and steel fiber. UHPC is composed of fine mineral particles below 0.5mm in diameter. In general, siliceous powder improves the mechanical properties of concrete by physical and chemical effect. Physical effect is related with filling interior voids which weaken the mechanical properties and chemical effect with reaction of $SiO_2$ with cement hydrates in a condition of high temperature and pressure. We evaluated the effect of siliceous powder's particle size on the mechanical properties of ultra high performance concrete in air pressure and $90^{\circ}C$ steam curing condition. siliceous powder's particle size in this study is in the range of $2{\mu}m$ to $26{\mu}m$. Fluidity in a fresh concrete, compressive strength, ultimate strain, elastic modulus and flexural strength in a hardened concrete was evaluated. We could find out that the smaller siliceous powder's particle size is, the better the fluidity and strength properties.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.263-271
• /
• 2010

e-Printing is a new manufacturing technology for electronic products and is based on traditional printing technology. The electronic products require a large area to facilitate printing and to be economical. A gravure printing system that supports a roll to roll (R2R) manufacturing process can be used to reduce the cost and to achieve the required accuracy. Many factors such as drying method, drying temperature, tension,-printing velocity, ink viscosity, ink conductivity, pattern accuracy, and dot geometry influence the performance of printed electronics. These factors are closely interrelated. The optimum condition for printing must be determined to enhance the performance of the printed electronics. In this study, lines and areas are printed using a gravure printer with conductive ink under different conditions of the above mentioned factors. The results are analyzed to investigate the influence of various factors on the performance of the printed electronics.