• Korean Chemical Engineering Research
• /
• v.53 no.2
• /
• pp.181-192
• /
• 2015

The aim of this study is to obtain optimum process condition for using two tower distribution to recycle the waste Propylene Glycol Monomethyl Ether Acetate (PGMEA) that is formed after washing LCD. The optimum process condition for the content of PGMEA, which is dependent variable, at 1st distillation was calculated according to Bottom temperature (BTM temperature), Reflux amount, Feed amount, Feed temperatures, and the optimum process conditions and optimum factors for the content of PGMEA at 2nd distillation according to Bottom temperature (BTM temperature), Reflux amount, Feed amount, Feed temperatures. At 1st distillation, Reflux amount, Feed amount, and Feed temperature are significant variables. However, it is found that the BTM temperature range is not significant in the range of process condition used in this study. The optimum process conditions are based on $5700{\ell}$ of Feed amount, $2500{\ell}$ of Reflux amount, $165^{\circ}C$ of BTM temperature, and $130^{\circ}C$ of Feed temperature. For the this condition, the predicted content of PGMEA was calculated as 92.12~94.62%. Significant factors at 2nd distillation are Reflux amount, Feed amount, and BTM temperature. Multicollinearity is between Reflux amount and BTM temperature. BTM was omitted in the multiple regression equation because there is a strong positive correlation between Reflux amount and BTM temperature. Base on $199^{\circ}C$ of BTM temperature, The optimum process conditions are based on $4275{\ell}$ of Feed amount, $6200{\ell}$ of Reflux amount and $130^{\circ}C$ of Feed temperature. In this condition, the predicted content of PGMEA was calculated as 99.0~99.5%.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3423-3428
• /
• 2007

This paper shows that inlet humidity condition at cathode side is one of dominant parameters affecting the performance of PEMFC. To investigate effects of inlet humidity condition, the performance measurements were conducted for a single PEMFC with two operating variables : cathode relative humidity and dry condition in anode dry. The fuel cell employed for the experiments is a unit PEMFC with a 25$Cm^2$, Nafion$^(R)$112 membrane. As a result of this study, the cell performance is getting higher by increasing inlet humidity condition at cathode side. The cell performance is different from each operating temperature an it has maximum30% higher than dry condition at 60$^{\circ}C$ operating temperature with 80% relative humidity.

• Fashion & Textile Research Journal
• /
• v.7 no.6
• /
• pp.665-672
• /
• 2005

The purpose of this study was to assess the feasibility and the effects of near infrared lighted garments on thermo-physiological responses in human body. Seven healthy adult men were recruited for this study. All subjects were informed the contents and purpose of this study. The experiment was carried out in a climate chamber of $32^{\circ}C$, 60%RH with 'Rest', 'Exercise' and 'Recovery' period. The experimental garments consisted of briefs, undershirts(sleeveless), nightclothes, T-shirts, knee-trousers and socks. Subjects participated in two experiments, one was wearing near infrared lighted garments(NIR-O), the other was wearing regular garments(NIR-X). The order of experiment was randomized, and subjects wore experimental garments before 24 hours in order to benefit by near infrared light. Measurement items included rectal temperature ($T_{re}$), mean skin temperature ($\bar{T}_{sk}$), sweat rate, heart rate, oxygen uptake and subjective sensation. The results are as follows: As to the variation of rectal temperature and mean skin temperature, value of wearing NIR-X was higher than value of wearing NIR-O, indicating a significant level of difference (p<.001). Sweat rate under NIR-O and NIR-X condition were 575.35 g and 535.75 g, respectively. Heart rate value of NIR-X condition was higher than NIR-O. Oxygen uptake measured during experiment was the higher in NIR-X condition with significant difference (p<.001). In the subjective sensation, the value of NIR-O condition was higher than NIR-X condition without significantly difference.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.3
• /
• pp.14-20
• /
• 2015

It is important to understand psychological and physiological responses of occupants who seated in a chair in order to shape a comfortable indoor official environment. So it is needed to find out optimal seated conditions. The purpose of this study was to explore optimal condition of seat air conditioning control based on psychological or subjective responses (perceived temperature and comfort sensation) and physiological responses (heartrate variability; HRV). To do this, experimental conditions were designed by the difference of indoor temperature and seat air conditioning temperature. In the experiment 1, seven experimental conditions were designed with one control condition which was not used seat air conditioning system, and six experimental conditions which the difference of indoor temperature and seat air conditioning temperature ($-1^{\circ}C{\sim}-6^{\circ}C$). In the experiment 2, four experimental conditions were designed with one control condition and three experimental conditions ($-3^{\circ}C{\sim}-5^{\circ}C$). In addition, participants' psychological or subjective response was measured by CSV (comfort sensation vote) and PTS (perceived temperature sensitivity) as a psychological or subjective response, and heartrate variability was measured as a physiological response. As a result, in the experiment 1, it was reported that the optimal conditions of seat air conditioning control based on participants' psychological or subjective comfort were from $-3^{\circ}C$ to $-5^{\circ}C$ experimental conditions. In addition, in the experiment 2, it was reported that the optimal condition of seat air conditioning control based on participants' physiological comfort was $-4^{\circ}C$ experimental condition. These results suggested that seat air conditioning could affected to comfort sensation of occupants in an appropriate range, rather than unconditionally.

• Journal of Mechanical Science and Technology
• /
• v.20 no.1
• /
• pp.158-166
• /
• 2006

Extended Graetz problem in microtube is analyzed by using eigenfunction expansion to solve the energy equation. For the eigenvalue problem we applied the shooting method and Galerkin method. The hydrodynamically isothermal developed flow is assumed to enter the microtube with uniform temperature or uniform heat flux boundary condition. The effects of velocity and temperature jump boundary condition on the microtube wall, axial conduction and viscous dissipation are included. From the temperature field obtained, the local Nusselt number distributions on the tube wall are obtained as the dimensionless parameters (Peclet number, Knudsen number, Brinkman number) vary. The fully developed Nusselt number for each boundary condition is obtained also in terms of these parameters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.8-13
• /
• 2010

Many vehicles have significantly under-inflated tires, primarily because drivers infrequently check their vehicles' tire pressure. When a tire is used while significantly under-inflated, its sidewalls flex more and the tire temperature increases, increasing stress and the risk of failure. In this study we evaluated tire safety and economical efficiency at various inflation pressure. For tire safety we performed FMVSS indoor durability test, measurement of rolling tire temperature, braking performance at dry/wet road condition, and rolling resistance test for economical efficiency. Results show that low pressure decreases tire durability of both speed-increase condition and load-increase condition. Heat temperature of rolling tire increases as pressure decreases and significantly under-inflated tires cause increase of vehicle's stopping distance at wet road condition. Also Under-inflation increases the rolling resistance of a tire and, correspondingly, decreases vehicle's fuel economy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.149-154
• /
• 1993

In heavy grinding that is on of the high efficient grinding method, meaningful deformation is generated by high temperature. So, after machining, geomeric error generated od the workpiece. The most important factor on the geometric error is temperature difference between upper layer and lower layer (T $_{d}$) . Relations between Td and grinding condition and maximum geometric error and grinding condition are obtained by experiment. This relations are used in fuzzy algorithm for improvement geometric accuracy. The main results are follows : (1) The linear relation between maximum geometric error and grinding condition is ovtained by experiment. (2) The linear relation between maximum temperature difference between upper layer and lower layer and grinding condition is ovtained by experiment. (3) Control peth of wheel for improvement geometric accuracy is obtained by using the fuzzy algorithm.m.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.636-639
• /
• 1996

We have developed a part of hydraulic stroke sensing cylinder using magnetic sensor that can detect each position under severe construction fields. In this paper, for evaluating the developed cylinder under various environment condition, thermal control systems and two hydraulic systems to be coupled consist of. The former is composed of an heater case, temperature sensor, and interface circuits which include SCR(silicon controlled rectifier) for the control of the voltage's phase. The latter is composed of an hydraulic cylinder for position control with solenoid valve (ON/OFF motion) and a load cylinder with proportional reducing valve. To obtain the various performance evaluation, it is carried out under high temperature condition in thermal system controlled by using Ziegler-Nichols PID tuning method and artificial disturbances such as impulse or constant force. The results show that the developed cylinder has good performance under the various environment condition.

• 한국연소학회:학술대회논문집
• /
• 2006.04a
• /
• pp.39-45
• /
• 2006

Analysis of the internal state of the blast furnace is needed to predict and control the operating condition. Especially, it is important to develop modeling of blast furnace for predicting cohesive zone because shape of cohesive zone influences overall operating condition of blast furnace such as gas flow, chemical reactions and temperature. because many previous blast furnace models assumed cohesive zone to be fixed, they can't evaluate change of cohesive zone shape by operation condition such as PCR, blast condition, and production rate. In this study, an axi-symmetric 2-dimensional steady state model is proposed to simulate blast furnace process. In this model, cohesive zone is changed by solid temperature range, FVM is used for numerical simulation. To find location of cohesive zone whole calculation procedure is iterated Until cohesive zone is converged. Through this approach, shape of cohesive zone, velocity, composition and temperature within the furnace are predicted by model.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.792-795
• /
• 2002

In previous researches, it is reported that Ti-10Ta-10Nb is robuster than Ti-6A1-4V which is used as a biomaterial in a experiment of cytotoxicity. Ti-10Ta-10Nb has enough hardness to be required as a biomaterial because the change of its hardness can be controlled more than 100% according to heat treatment condition and manufacturing condition. There are many hardness changing condition including Cast Homogenization, Solution treatment. Forging, Rolling in this research. The changing form and amount of new Ti-10Ta-10Nb to be developed in this researches, are measured as quantitative. Specially, the changing hardness amount of the specimen that is manufactured in single phase temperature, i.e. 80$0^{\circ}C$, are measured in case of high temperature rolling and high temperature cast condition.