• Journal of Advanced Marine Engineering and Technology
• /
• 제32권8호
• /
• pp.1257-1262
• /
• 2008

A long-distance remote sensing of temperature and current based on a fiber Bragg grating (FBG) is proposed and demonstrated. The thermal expanding effect of the epoxy and the Er-doped fiber ring laser (EFRL) are applied to the sensor system to enhance the temperature and current sensitivity. An EFRL with a 5 km-single-mode fiber and a FBG shows a high extinction ratio of more than 60 dB and a low power fluctuation of less than 1 dB. The metal wires are used to supply the current to the sensors. When the NOA65 puts on the FBG as a thermal expanding material, the temperature and current sensitivity of the lasing wavelength shift are about $30\;pm/^{\circ}C$ and 3pm/mA, respectively. The proposed sensing scheme is useful for measurement of current or temperature at a distant object of more than several km.

• 한국유체기계학회 논문집
• /
• 제14권1호
• /
• pp.42-47
• /
• 2011

Measurement uncertainty analysis of fuel flow using turbine flowmeter was performed for the case of altitude engine test. SAE ARP4990 was used as the fuel flow calculation procedure, as well as the mathematical model for the measurement uncertainty assessment. The assessment was performed using Sensitivity Coefficient Method. 11 parameters involved in the calculation of the flow rate were considered. For the given equipment setup, the measurement uncertainty of fuel flow was assessed in the range of 1.19~1.86 % for high flow rate case, and 1.47~3.31 % for low flow rate case. Fluctuation in frequency signal from the flowmeter had the largest influence on the fuel flow measurement uncertainty for most cases. Fuel temperature measurement had the largest for the case of low temperature and low flow rate. Calibration of K-factor and the interpolation of the calibration data also had large influence, especially for the case of very low temperature. Reference temperature, at which the reference viscosity of the sample fuel was measured, had relatively small contribution, but it became larger when the operating fuel temperature was far from reference temperature. Measurement of reference density had small contribution on the flow rate uncertainty. Fuel pressure and atmospheric pressure measurement had virtually no contribution on the flow rate uncertainty.

• 대한토목학회논문집
• /
• 제40권2호
• /
• pp.183-189
• /
• 2020

이 논문은 인장 응력, 주변 온도 및 인가 주파수에 대한 강선의 전기적 임피던스 민감도에 관한 실험적 조사이다. 다양한 응력 수준 및 온도에 대해서, 강선의 전기적 임피던스가 자가진단 시스템에서 측정되었다. 세 가지 경우의 실험이 다양한 온도 조건, 응력 수준 및 적용 주파수에 대해서 수행되었다. 주어진 주파수에서 온도가 상승하고 응력이 감소하면 강선의 전기 임피던스가 증가한다. 실험 결과는 전기적 임피던스와 온도 사이의 상관관계가 모든 응력 수준에서 선형 관계임을 보여준다. 온도에 대한 임피던스의 감도는 응력보다 훨씬 높다는 점이 주목 된다.

• 전자공학회논문지SC
• /
• 제48권1호
• /
• pp.1-8
• /
• 2011

MR 센서에 의해 지구자기장의 세기를 측정하여 방위각을 결정하는 전자 Compass의 정밀도는 MR센서 및 OP-Amp.의 온도 Drift, DC Offset등 소자에 의한 오차, 측정주변 자성체에 의한 자기장의 왜곡, 및 Compass Tilt에 의한 오차 등의 영향을 받는다. 본 연구에서는 Set/Reset Pulse 방법에 의해 MR 센서 및 OP-Amp의 온도 Drift 및 DC Offset에 의한 오차를 해결하였고, 주변 자성체에 의한 자기장의 왜곡에 의한 오차를 Hard-Iron Calibration 루틴 수행에 의해 보상하였으며, Compass Tilt에 의한 오차를 Euler Rotational Equation에 의해 보상할 수 있는 3축 MR 센서 및 3축 Accelerometer를 기반으로 하는 전자 Compass 를 설계하였다. 특히 이와 샅이 설계한 전자 Compass를 가지고 3측 MR 센서의 서로 다른 Sensitivity와 OP-Amp.의 서로 다른 Gain등을 규준화하기 위한 Sensitivity Calibration 루틴 수행 시 Tilt의 발생으로 야기되는 오차를 정량적으로 분석하였으며, 이를 바탕으로 $1^{\circ}$정도(精度) Compass를 설계할 수 있었다.

• 수산해양기술연구
• /
• 제26권4호
• /
• pp.372-379
• /
• 1990

The effect of primary solidification phase on the solidification cracking sensitivity, corrosion resistance and toughness at cryogenic temperature was investigated for the austenitic stainless steel welds. The conclusions were summarized as follows; 1. Soldification crack sensitivity of austenitic stainless steel welds depends on the primary solidification mode. 2. Austenitic stainless steels were very susceptible to solidification cracking in case of solidification as primary ${\gamma}$ and immune when solidified as primary $\delta$. 3. When the ratio of Creq/Nieq is in the range of 1.46 to 1.55, the most resistance against solidification cracking was obtained. These results agreed well with the relationship between primary solidification mode, corrosion resistance and toughness at cryogenic temperature. 4. Optimum toughness, corrosion and solidification cracking resistance can be obtained when alloys having chemical compositions described above and solidifies as primary $\delta$ containing no ferrite at room temperature.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1285-1287
• /
• 1998

Vibration measurements to monitor the condition of machinery and machine elements offers several advantages over traditional methods of nondestructive evaluation. RIST(Research Institute of Industrial Science & Technology) has established a calibration system for accelerometers that measures within a frequency range from 2Hz to 6,300Hz and a temperature range from $-40^{\circ}C$ to $180^{\circ}C$. The calibration procedures are based on the principle of the comparison method. To monitor vibration signals of machinery and machine elements, annular shear type piezoelectric accelerometers employing solid state microelectronics were fabricated. The voltage sensitivity and resonant frequency of fabricated accelerometers was 83mV/g, 23kHz, respectively. This paper discusses the method of fabrication of annular shear type piezoelectric accelerometers and the results of field tests in POSCO(Pohang Iron & Steel Co. LTD.).

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.73-76
• /
• 2002

In this paper we present an integrated Hail sensor It for fan motors, fabricated in industrial bipolar process. As a discrete Hall sensor and signal processing circuitry In the fan motor system were Integrated into single chip a temperature dependence of Hall sensitivity and Hall offset voltage can be compensated and cancelled by on-chip circuitry. We Propose a novel temperature compensation of Hall sensitivity with negative temperature coefficient (TC) using the differential amplifier gain with Positive TC. After a package of the chip was sealed using a plastic Package 20 Pins, the thermal and magnetic characteristics were investigated. The obtained experimental results are in agreement with analytical predictions and have more excellent performance than\ulcorner conventional the fan motor system using discrete Hall sensor.

• 대한전자공학회논문지
• /
• 제25권3호
• /
• pp.307-314
• /
• 1988

The thin, square-diaphragm silicon pressure sensor utilizing shear piezoresistance effect was designed and fabricated and its characteristics were examined. The sensor has only one diffused resistor, whereas conventional full-bridge sensor has four. Sensitivity is somewhat lower but temperature compensation is easier than the latter. The proposed sensor was fabricated with only one p-type diffused resistor of the dimension of 113x85\ulcorner\ulcornerlocated near the center of the edge of the diaphragm. The resistor was at 45\ulcornerwith the edge of the diaphragm. The sensitivity of the sensor was 36\ulcorner/V\ulcornermHg and was linear in the pressure range from 0 to 300 mmHg. The temperature coefficient without temperature compensation was 55 ppm/\ulcorner and it was decreased to about 0.17 mmHg/\ulcorner with compensation in the range from 10 to 60\ulcorner.

• Journal of Magnetics
• /
• 제4권1호
• /
• pp.17-21
• /
• 1999

The GMR ($d_Cu$) oscillatory behaviour as well as the widths of first and the second antiferromagnetically coupled ranges of the Permalloy ($Py=Ni_{83}Fe_{17}$)/Cu multilayers have been found to be strongly affected not only by the presence of the superparamagnetic/paramagnetic entitles located at the Py/Cu interfaces but mainly by the existence of the magnetic bridges between Py layers. The effectiveness of the magnetic bridges has been found to be temperature dependent, leading to the temperature dependence of the remnant to saturation magnetization ratio ($M_R/M_S$). We have found that for Py/Cu multilayers with equal Py and Cu layer thicknesses a high field sensitivity of the GMR effect (0.4%/Oe) and negligible hysteresis can be achieved when the number of Py layers decreases from 100 to 6. Sensitivity can be further improved by increasing the Py layers thickness, but the hysterstic effect becomes more pronounced then.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.35-39
• /
• 2013

In this paper, we developed an optical sheet for LED lighting with integrated $CO_2$ gas and temperature sensor which can monitor at the indoor environment. The optical sheet for LED lighting is fabricated through PMMA(Polymethyl methacrylate) injection process using mold. This research enables to fabricate the reflective sheet, light-guide plate and the prism sheet in a optical sheet. The fabricated sheet demonstrates higher intensity of optical efficiency compared with single-sided sheets. The $CO_2$ sensor was fabricated using NDIR(NON-Dispersive Infrared) method and it has $0.0235mV/V{\cdot}PPM$ sensitivity. The temperature sensor was fabricated using RTD(Resistance temperature detector) method and it has $0.563{\Omega}/^{\circ}C $sensitivity.