• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.2
• /
• pp.187-197
• /
• 1996

A computer program for thermal design analysis has been developed to predict the operating characteristics and performance of an absorption heat pump to recover $30{\sim}40^{\circ}C$ of waste hot water. The effects of heat transfer area of the system components, temperature and mass flow rate of heat transfer medium, and solution circulation rate on the system performance are investigated in detail. The results obtained indicate that the COP is increased with a decrease in the temperature of driving steam and with an increase in the temperature of waste hot water while the COP is little affected by the variation of a hot water temperature. It is also found that the heating output is increased with an increase in the temperature of waste hot water and driving steam as well as with a decrease in the temperature of hot water. The simulation results are also compared with the experimental results for a periodic operation of the system and obtained a satisfactory agreement.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.600-603
• /
• 2000

In the high carbon steel wire drawing process, the wire temperature increases as the drawing speed is faster in order to increase the production rate in the shop floor. The rapid temperature rise causes the wire fracture in the dry wire drawing process. So, in this paper, the isothermal pass schedule program, which includes the calculation method of wire temperature at each pass, is proposed to prevent the wire fracture due to the temperature rise. Using the isothermal pass schedule program, it is newly proposed the pass schedule design system that prevents the cup-cone defects, improves the elongation of the final products and assures further deformation. As a result, the temperature rise of the wire was decreased and the production rate of the final product is remarkably grown up according to the increase of the final drawing speed than that of the conventional process. Also, the proposed pass schedule design system could give a useful information to the process designer who would design the high carbon steel wire drawing process.

• Asian-Australasian Journal of Animal Sciences
• /
• v.6 no.2
• /
• pp.275-279
• /
• 1993

A study using dairy heifers was conducted to determine the effect of environmental temperature on heat production differing in feed intake level. The design consisted of three levels of feed intake (low, medium and high) and two environmental chamber temperature (15 and $30^{\circ}C$) with four replications in each treatment. Rectal temperature (RT), respiration rate (RR), heart rate (HR) and heat production (HP) were then measured. At the both environmental temperature, RT, RR and HR increased with the increase in feed intake level. The RT and RR also increased with the elevation of environmental temperature. The HP of $30^{\circ}C$ was significantly higher (4.8-8.9%) than $15^{\circ}C$. The estimated metabolizable energy requirement for maintenance (MEm) was higher (p<0.05) at $30^{\circ}C$ ($554.7kJ/kg^{0.75}$ d) than $15^{\circ}C$ (464.9 kJ/kgd). It was suggested that the decreasing in productive efficiency under hot environmental conditions partly associated with the increase in HP, which associated with the change in heat loss mechanism from sensible path to evaporative path.

• Journal of the Korean Chemical Society
• /
• v.31 no.5
• /
• pp.395-399
• /
• 1987

The two dissociation constants of leucine were measured in the temperature range from 15 to 40$^{\circ}$C and pressure up to 2,500 bar by conductometric method. Both constants were increased as the temperature increased but pressure effect was not same as temperature effect. The first constants were increased as pressure increase but the second constants were decreased as pressure increase in the law temperature range but increased in some higher temperature range. These phenomena were discussed from the thermodynamic properties of the dissociation reactions.

• Journal of the Korean Ceramic Society
• /
• v.49 no.1
• /
• pp.111-117
• /
• 2012

Dependencies of thermal properties on the crystallization behavior of $0.9CaMgSi_2O_6-0.1MgSiO_3$ glass-ceramics were investigated as a function of heat-treatment temperature from $750^{\circ}C$ to $950^{\circ}C$. The crystallization behavior of the specimens depended on the heat-treatment temperature, which could be evaluated by differential thermal analysis (DTA), Fourier transform infrared spectroscopy (FT-IR), and X-ray diffraction (XRD) analysis by the Rietveld-reference intensity ratio (RIR) combined procedure. With an increase of the heat-treatment temperature, the thermal conductivity and thermal diffusivity of the heat-treated specimens increased. These results could be attributed to the increase of crystallization with heat-treatment temperature. However, the specific heat capacity of the heat-treated specimens was not affected by the heat-treatment temperature. The thermal conductivities measured from $25^{\circ}C$ to $100^{\circ}C$ were also discussed for application to lighting-emitting diode (LED) packages and substrate materials.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.1
• /
• pp.27-32
• /
• 2014

In this paper, PZT piezoelectric ceramic specimens with 4 compositions (Zr/Ti=50/50, 53/47, 56/44, 58/42) in $Pb(Zr,Ti)O_3$ system were fabricated. We studied effects of poling strength and thermal aging on the temperature characteristics of eletromechanical coupling factor k31 of the specimens, which were poled with the DC electric fields, 1.5, 2.5 and 3.5 kV/mm respectively and thermally aged for an hour at $200^{\circ}C$. The eletromechanical coupling factor k31 of the specimen with the composition Zr/Ti= 53/47, nearest to the morphotropic phase boundary decreased the most greatly, irrelevant to the intensity of poling field, due to 1st thermal aging. And the temperature coefficient of eletromechanical coupling factor k31 was (-) in the tetragonal phase composition and (+) in the rhombohedral phase composition, which is reverse in the temperature coefficient of resonance frequency. It is interesting that eletromechanical coupling factor k31 of PZT ceramics is shown to be able to increase as temperature increase in the interval $-20{\sim}80^{\circ}C$.

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.9-13
• /
• 1999

The influence of quenching temperature and annealing time on superconducting characteristics has been investigated for a $(Pb_{0.6}V_{0.4})Sr_2(Ca_{0.65}Er_{0.35})Cu_2O_z$ compound. From the resistivity measurements for samples annealed at $400^{\circ}C$ to $860^{\circ}C$ in oxygen and subsequently quenched, it is observed that $T_c$(zero) of the sample decreases with the increase of annealing temperature up to $600^{\circ}C$ and increases again beyond $700^{\circ}C$. Annealings of the sample at $860^{\circ}C$ show that $T_c$(zero) goes through a maximum of 62K with the increase of the annealing time. It is also found that $T_c$(zero) of the sample quenched from high temperature decreases when the sample is subjected to low temperature annealing below. $600^{\circ}C$ in oxygen. The experimental results indicate that the as-prepared samples contain excessive oxygen and removal of this excessive oxygen in as-prepared samples is a key factor in controlling the superconducting properties of the samples and are discussed in connection with thermal gravimetric measurements.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.315-318
• /
• 2004

The Advantages of hot machining are the reduction of cutting forces, tool wear, and the increase of material removal rates. In this study, a hot-machining characteristics of milling by CBN tip was exprimentely analyzed, and the influence of the surface temperature and the depth of cut on the tool life were investigated. The selection of a heating method for obtaining ideal temperature of metals in machining is important. Faulty heating methods could induce unwanted structural changes in the workpiece and increase the cost. This study uses gas flame heating. It is obtained that tungsten carbide-alloyed has a recrystallisation temperature range of $800-1000^{\circ}C$ which is the high heating temperature that might induce unwanted structural changes. If it is performed at temperatures higher than $800^{\circ}C$ in machining, the possibility of unwanted structural changes and the increased wear of tool can be shown. Consequently, in hot machining of tungsten carbide-alloy, this study has chosen $400^{\circ}C-600^{\circ}C$ because the heating temperature might be appropriate in view of the cost and workpiece considerations. The results of this study experimentally shows a new machining method for tungsten carbide-alloyed that decreases the wear rate of machining tools

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.489-492
• /
• 2007

Temperature and injection current dependence of elctroluminescence(EL) spectral intensity of the $In_{0.27}Ga_{0.73}N/GaN$ multi-quantum-well(MQW) have been studied over a wide temperature and as a function of injection current level. EL peaks also show significant broadening into higher photon energy region with the increase of injection current. This is explained by the band-filling effect. When temperature is slightly increased to 300 from 15 K, the EL emission peak showed red-blue-red shift. It can be explained by the carrier localization by potential fluctuation of multiple quantum well and band-gap shrinkage as temperature increase. It is found that a temperature-dependent variation pattern of the EL efficiency under very low and high injection currents show a drastic difference. This unique EL efficiency variation pattern with temperature and current is explained field effects due to the driving forward bias in presence of internal(piezo and spontaneous polarization) fields.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.1
• /
• pp.23-28
• /
• 2000

The fatigue crack growth behavior of the cold-rolled STS 304 steel developed for membrane material of LNG storage tank was examined experimentally at 293K, 153K and 111K. The fatigue crack growth rate(do/dN) tends to increase as the stress ratio (R) increases over the testing temperature when compared at the same stress intensity factor range($\Delta$K). The effect of R on do/dN is more explicit at low temperatures than at room temperature. The resistance of fatigue crack growth at low temperatures is higher compared with that at room temperature which is attributed to the extent of strain-induced martensitic transformation at the crack tip. The temperature dependence of fatigue crack growth resistance is gradually vanished with an increase in $\Delta$K which correlates with a decreasing fracture toughness with decreasing temperature. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperature are mainly explained by the crack closure and the strengthening due to the martensitic transformation.