• International Journal of Control, Automation, and Systems
• /
• v.1 no.3
• /
• pp.395-400
• /
• 2003

A quantitative performance evaluation of a robot teaching method using a force/moment direction sensor is presented. The performance of the teaching method using the force/moment direction sensor is compared with the conventional teaching pendant method. Two types of teaching tasks were designed and the teaching times required to complete the teaching tasks were measured and compared. Task A requires a teaching motion that involves four degrees of freedom motion. Task B requires a teaching motion that involves six degrees of freedom motion. It was found that, by using the force/moment direction sensor method, the teaching times were reduced by 25% for Task A and 45% for Task B compared to the teaching pendant method.

• Transactions on Control, Automation and Systems Engineering
• /
• v.3 no.4
• /
• pp.236-241
• /
• 2001

Teach pendant is the most widely used means of robot teaching at present. Despite the difficulties of using the motion command buttons on the teach pendant, it is an economical, robust, and effective device for robot teaching task. This paper presents the development of a force/moment direction sensor named COSMO that can improve the teach pendant based robot teaching. Robot teaching experiment of a six axis commercial robot using the sensor is described where operator holds the sensor with a hand, and move the robot by pushing, pulling, and twisting the sensor in the direction of the desired motion. No prior knowledge of the coordinate system is required. The function of the COSMO sensor is to detect the presence f force and moment along the principal axes of the sensor coordinate system. The transducer used in the sensor is micro-switch, and this intuitive robot teaching can be implemented at a very low cost.

• Journal of Industrial Technology
• /
• v.21 no.A
• /
• pp.89-96
• /
• 2001

A low cost force./moment sensor that can be used in the robot teaching task is presented. Force Sensing Resistor is used as the transducer. The principle of force/moment detection is explained, the architecture of the sensor is shown, and the measurement of the force/moment is presented. The force/moment sensor shown in this work is not meant to be used in a precise force/moment control, but it is intended to be used in the robot teaching where low accuracy can be tolerated.

• The Journal of Korea Robotics Society
• /
• v.14 no.4
• /
• pp.311-317
• /
• 2019

Direct teaching is an essential function for collaborative robots for easy use by non-experts. For most robots, direct teaching is implemented only in joint space because the realization of Cartesian space direct teaching, in which the orientation of the end-effector is fixed while teaching, requires a measurement of the end-effector force. Thus, it is limited to the robots that are equipped with an expensive force/torque sensor. This study presents a Cartesian space direct teaching method for torque-controlled collaborative robots without either a force/torque sensor or joint torque sensors. The force exerted to the end-effector is obtained from the external torque which is estimated by the disturbance observer-based approach with the friction model. The friction model and the estimated end-effector force were experimentally verified using the robot equipped with joint torque sensors in order to compare the proposed sensorless approach with the method using torque sensors.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1621-1623
• /
• 1997

Use of teaching pendant is the most widespread and economical way to teach desired motion to robots. It is also very primitive,time consuming and ineffective way of teaching which has not changed since the early days of robot. In order to reduce the teaching effor, a new efficient form of teaching is needed. Also, the recent robotics research trend into service robots such as home robot, nurse robot and medical robot calls for a new teaching method which is both easy and inexpensive. In this paper, the design and operation principle of a low cost force/moment sensor is presented. The proposed sensor architecture is so simple and inexpensive that it opens the prospect for a new paradigm of robot teaching which is easy and efficinet. Other prospective areas of application are tele-manipulation of robots wher it can be used in master arm, and virtual environment where it can be used as an user input device.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.7
• /
• pp.1525-1530
• /
• 2014

In this research, we describe teaching based sweeping control for grinder robot has been proposed as a system which is suitable to work utilizing pressure sensitive alternative to human. Teaching method is used for grinder robots operations because of their position accuracy, path accuracy, and machining reaction force. A grinder robot for two-dimensional iron plate was developed on the basis of an force sensor based teaching method. An automatic-path-generation method and experimental results using specific points was adopted to reduce the number of teaching points and time. And also, in order to determine the proper machining conditions, various machining conditions such as grinder-wheel rotation speed and robot moving speed, were evaluated.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.5
• /
• pp.538-542
• /
• 2009

Industrial manipulators have been mostly used in large companies such as automakers and electronics companies. In recent years, however, demands for industrial manipulators from small and medium-sized enterprises are on the increase because of shortage of manpower and high wages. Since these companies cannot hire robot engineers for operation and programming of a robot, intuitive teaching and playback techniques of a robot manipulator should replace the robot programming which requires substantial knowledge of a robot. This paper proposes an intuitive teaching and playback algorithm used in assembly tasks. An operator can directly teach the robot by grasping the end-effector and moving it to the desired point in the teaching phase. The 6 axis force/torque sensor attached to the manipulator end-effector is used to sense the human intention in teaching the robot. After this teaching phase, a robot can track the target position or trajectory accurately in the playback phase. When the robot contacts the environment during the teaching and playback phases, impedance control is conducted to make the contact task stable. Peg-in-hole experiments are selected to validate the proposed algorithm since this task can describe the important features of various assembly tasks which require both accurate position and force control. It is shown that the proposed teaching and playback algorithm provides high positioning accuracy and stable contact tasks.

• The Journal of Korea Robotics Society
• /
• v.15 no.4
• /
• pp.309-315
• /
• 2020

This study shows a control strategy that acquires both precision and manipulation sensitivity of remote center motion with manual traction for a surgical assistant robot. Remote center motion is an essential function of a laparoscopic surgical robot. The robot has to keep the position of the insertion port in a three-dimensional space, and general laparoscopic surgery needs 4-DoF (degree-of-freedom) motions such as pan, tilt, spin, and forward/backward. The proposed robot consists of a 6-axis collaborative robot and a 2-DoF end-effector. A 6-axis collaborative robot performs the cone-shaped trajectory with pan and tilt motion of an end-effector maintaining the position of remote center. An end-effector deals with the remaining 2-DoF movement. The most intuitive way a surgeon manipulates a robot is through direct teaching. Since the accuracy of maintaining the remote center position is important, direct teaching is implemented based on position control in this study. A force/torque sensor which is attached to between robot and end-effector estimates the surgeon's intention and generates the command of motion. The predefined remote center position and the pan and tilt angles generated from direct teaching are input as a command for position control. The command generation algorithm determines the direct teaching sensitivity. Required torque for direct teaching and accuracy of remote center motion are analyzed by experiments of panning and tilting motion.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.19 no.1
• /
• pp.85-92
• /
• 2024

In this paper, we developed an intuitive teaching and control system that directly teaches a task by holding the tip of a robotic arm and moving it to a desired position. The developed system consists of a 6-axis force sensor that measures position and attitude forces at the tip of the robot arm, an algorithm for generating robot arm joint speed control commands based on the measured forces at the tip, and a self-made 6-axis robot arm and control system. The six-dimensional force/torque of the position posture of the robot arm operator steering the handler is detected by the force sensor attached to the handler at the leading edge and converted into velocity commands at the leading edge to control the 7-axis robot arm. The verification of the research method was carried out with a self-made 7-axis robot, and it was confirmed that the proposed force sensor-based robot end-of-arm control method operates successfully through experiments by teaching the operator to adjust the handler.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.9
• /
• pp.38-44
• /
• 2009