• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.2
• /
• pp.66-72
• /
• 2024

In this study, the applicability of CCMs (Carbondioxide conversion capture materials) manufactured by reacting carbon dioxide gas with DG (Desulfurization gypsum) as a cement substitute for secondary concrete products were evaluated and the basic physical properties of CCMs-mixed mortar and concrete specimens were measured to derive the optimal mixing ratio. The main chemical oxides of CCMs were CaO and SO₃, and the main crystalline phases were CaSO₄·2H₂O, Ca(OH)₂, CaCO₃, and CaSO₄. In addition, by the results of particle size analysis and heavy metal measurement, the applicability of CCMs as a cement substitute for secondary concrete products was confirmed. As a result of measuring the strength behavior using mortar and concrete specimens with CCMs, the compressive and flexural strength decreased as the mix ratio of CCMs increased, but requirements by the standards for interlocking blocks and retaining wall blocks, which are target products in this study, were satisfied up to the optimal mixing ratio of 10 wt.% substitution. Therefore, its applicability as a cement substitute for secondary concrete products was confirmed.

• Journal of Korean Society of Disaster and Security
• /
• v.17 no.2
• /
• pp.1-11
• /
• 2024

Most reservoirs in South Korea are earthen dams, mainly because they are cost-effective and easy to construct. However, earthen dams are highly vulnerable to seepage and overtopping, making them prone to sudden failure during excessive flooding. Such sudden failures can lead to a rapid increase in flood discharge, causing significant damage to downstream rivers and inhabited areas. This study investigates the effect of riprap placement on the slopes of earthen dams in delaying dam failure. Delaying the failure time is crucial as it allows more time for evacuation, significantly reducing potential casualties, which is essential from a disaster response perspective. Hydraulic experiments were conducted in a straight channel, using two different sizes of riprap for protection. Unlike previous studies, these experiments were performed under unsteady flow conditions to reflect the impact of rising water levels inside the dam. The target dam for the study was a cofferdam installed in a diversion tunnel. Experimental results indicated that the presence of riprap protection effectively prevented slope failure under the tested conditions. Without riprap protection, increasing the size of the riprap delayed the failure time. This delay can reduce peak discharge, mitigating damage downstream of the dam. Furthermore, these findings can serve as critical reference material for establishing emergency action plans (EAP) for reservoir failure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.2
• /
• pp.59-66
• /
• 2008

In the construction site, to improve the man-dependent form work, non-stripping form has been studied but the developed non-stripping form was hard to applied with respect to the cost, form size and performance. This study is for evaluating the adaptability of the developed non-stripping form named as high performance permanent form (HPPF). To do this, the analytical approach and parametric study were performed based on the research for fundamental material characteristic of the HPPF. The target concrete structure is a wall structure because of its effectiveness of HPPF. To evaluate the structural efficiency of the HPPF applied wall structure, FEM analysis was performed to decide the maximum placing height at one time then it was applied to design the wall structure. In the result of the analysis, the HPPF applied wall structure showed the lots of advantages that it can reduce the cost resulted from reducing concrete and steel rebar even if it has same structural performance to the conventional concrete wall structure with same dimension. With this analysis result, it can be evaluated that the HPPF applied concrete structure can be a concrete structure with the long term durability in site.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.4
• /
• pp.49-60
• /
• 2024

Ground-penetrating radar (GPR) enables rapid data acquisition over extensive areas, but interpreting the obtained data requires specialized knowledge. Numerous studies have utilized numerical analysis methods to examine GPR signal characteristics under various conditions. To develop more realistic numerical models, the heterogeneous nature of the ground, which causes clutter, must be considered. Clutter refers to signals reflected by objects other than the target. The Peplinski material model and fractal techniques can simulate these heterogeneous characteristics, yet there is a shortage of research on the necessary input parameters. Moreover, methods for quantitatively evaluating the similarity between field and analytical data are not well established. In this study, we calculated the autocorrelation coefficient of field data and determined the correlation length using the autocorrelation function. The correlation length represented the temporal or spatial distance over which data exhibited similarity. By comparing the correlation length of field data with that of the numerical model incorporating fractal weights, we quantitatively evaluated a numerical model for heterogeneous ground. Consequently, the results of this study demonstrated a numerical modeling technique that reflected the clutter characteristics of the field through correlation length.

• Geophysics and Geophysical Exploration
• /
• v.11 no.3
• /
• pp.250-262
• /
• 2008

In order to assess the feasibility of the dipole-dipole electric method to the investigation of metallic ore deposit, both field data simulation and inversion are carried out for several simplified ore deposit models. Our interest is in a vein-type model, because most of the ore deposits (more than 70%) exist in a vein type in Korea. Based on the fact that the width of the vein-type ore deposits ranges from tens of centimeters to 2m, we change the width and the material property of the vein, and we use 40m-electrode spacing for our test. For the vein-type model with too small width, the low resistivity zone is not detected, even though the resistivity of the vein amounts to 1/300 of that of the surrounding rock. Considering a wide electrode interval and cell size used in the inversion, it is natural that the size of the low resistivity zone is overestimated. We also perform field data simulation and inversion for a vein-type model with surrounding hydrothermal alteration zones, which is a typical structure in an epithermal ore deposits. In the model, the material properties are assumed on the basis of resistivity values directly observed in a mine originated from an epithermal ore deposits. From this simulation, we can also note that the high resistivity value of the vein does not affect the results when the width of the vein is narrow. This indicates that our main target should be surrounding hydrothermal alteration zones rather than veins in field survey. From these results, we can summarize that when the vein is placed at the deep part and the difference of resistivity values between the vein and the surrounding rock is not large enough, we cannot detect low resistivity zone and interpret the subsurface structures incorrectly using the electric method performed at the surface. Although this work is a little simple, it can be used as references for field survey design and field data Interpretation. If we perform field data simulation and inversion for a number of models and provide some references, they will be helpful in real field survey and interpretation.

• Journal of the Korean Society of Radiology
• /
• v.11 no.5
• /
• pp.335-341
• /
• 2017

Cyclotron is a device that accelerates positrons or neutrons, and is used as a facility for making radioactive drugs having short half-lives. Such radioactive drugs are used for positron emission tomography (PET), which is a medical apparatus. In order to make radioactive drugs from a cyclotron, a nuclear reaction must occur between accelerated positrons and a target. After the reaction, unncessary neutrons are produced. In the present study, radioactivation generated from the collisions between the concrete shielding wall and the positrons and neutrons produced from the cyclotron is investigated. We tracked radioactivated radioactive isotopes by conducting experiments using FLUKA, a type of Monte Carlo simulation. The properties of the concrete shielding wall were comparatively analyzed using materials containing impurities at ppm level and materials that do not contain impurities. The generated radioactivated nuclear species were comparatively analyzed based on the exposure dose affecting human body as a criterion, through RESRAD-Build. The results of experiments showed that the material containing impurities produced a total of 14 radioactive isotopes, and $^{60}Co$(72.50%), $^{134}Cs$(16.75%), $^{54}Mn$(5.60%), $^{152}Eu$(4.08%), $^{154}Eu$(1.07%) accounted for 99.9% of the total dose according to the analysis having the exposure dose affecting human body as criterion. The $^{60}Co$ nuclear species showed the greatest risk of radiation exposure. The material that did not contain impurities produced a total of five nuclear species. Among the five nuclear species, 54Mn accounted for 99.9% of the exposure dose. There is a possibility that Cobalt can be generated by inducive nuclear reaction of positrons through the radioactivation process of $^{56}Fe$ instead of impurities. However, there was no radioactivation because only few positrons reached the concrete wall. The results of comparative analysis on exposure dose with respect to the presence of impurities indicated that the presence of impurities caused approximately 98% higher exposure dose. From this result, the main cause of radioactivation was identified as the small ppm-level amount of impurities.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.330-337
• /
• 2011

In this research, the preparation processes for making a series of $\omega$-mercapto alkylamine 1 and $\omega$-mercapto alkanoic acid 2 useful for studying of the self-assembled monolayer(SAM) are described. The preparation methods of the first goal materials, $\omega$-mercapto alkylamines 1 were carried out as follows: First, $\omega$-phthalimide alkanol 3 was synthesized from commercially available potassium phthalimide derivatives and $\omega$-bromoalkanol in DMF at $80{^{\circ}C}$ via substitution reaction. After refluxing $\omega$-phthalimide alkanol 3 with hydrazine hydrate in ethanol followed by treating with c-HCl, $\omega$-aminoalkanol 4 was obtained in 76-98% yield, accompanied with side-product 5. Bromination of hydroxyl moiety of $\omega$-aminoalkanol 4 using aqueous hydrobromic acid furnished $\omega$-bromoamine 6 in 34-97% yields. Substitution reaction 6 with thiourea in 95% ethanol gave $\omega$-aminoalkanthiuronium 7, which was treated with aqueous strong base and aqueous strong sulfuric acid gave desired products, $\omega$-mercapto alkylamines 1 through overall 5 steps. The second target material, $\omega$-mercapto alkanoic acid 2 was prepared via 2 steps. $\omega$-bromo alkanoic acid was reacted with thiourea to give $\omega$-thiourea alkanoic acid 7 in 69-85%, which was treated with aqueous strong base and strong acid to furnish $\omega$-mercapto alkanoic acid 2 in 50-98%. The fabricated long-chain alkylthiol(LCAT) can be used as linkers to immobilize protein, enzyme and various kinds of biomolecules on the surface of metallic materials(Au, Pt, Ti) by SAM, and can be useful chemical tools for the application study on the surface modification of metallic materials.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.15 no.2
• /
• pp.47-65
• /
• 2020

With the era of the Fourth Industrial Revolution in sight, innovative business models utilizing new technologies are emerging, and startups are enjoying an abundance of opportunities based on the agility to respond to disruptive innovations and the opening to new technologies. However, what is most important in creating a sustainable start-up ecosystem is not the start-up itself, but the process of research-start-investment-investment-the leap to listing and big business-in order to build a virtuous circle of startups that leads to re-investment. To this end, the environment created in the hub area where start-ups were conducted is important, and these material and non-material environmental factors are described as being inclusive by the word "entrepreneurial ecosystem." This study aims to provide implications for Korea's entrepreneurial ecosystem through the study of the interaction of the elements that make up the start-up ecosystem and the relationship of ecosystem participants in Singapore. Singapore has been consistently mentioned as the top two Asian countries in assessing the start-up environment and business environment. In this process, six elements of the entrepreneurial ecosystem presented by Isenberg(2010)-policies, finance, culture, support, human resources, and market-are the best frameworks for analyzing entrepreneurial ecosystems in terms of well encompassing prior studies related to entrepreneurial ecosystem elements, and a model of regional transformation is formed focusing on some elements to suit Singapore, the target area of study. By considering that Singapore's political nature would inevitably have a huge impact on finance, Smart Nation policy was having an impact on university education related to entrepreneurship, and that the entrepreneurial networks and global connectivity formed within Singapore's start-up infrastructure had a significant impact on Singapore's start-up's performance, researches needed to look more at the factors of policy, culture and market. In addition, qualitative research of participants in the entrepreneurial ecosystem was essential to understand the internal interaction of the elements of the start-up ecosystem, so the semi-structured survey was conducted by visiting the site. As such, this study examined the status of the local entrepreneurial ecosystem based on qualitative research focused on policies, culture and market elements of Singapore's start-up ecosystem, and intended to provide implications for regulations related to start-ups, the role of universities and start-up infrastructure through comparison with Korea. This could contribute not only to the future research of the start-up ecosystem, but also to the creation of a start-up infrastructure, boosting the start-up ecosystem, and the establishment of the orientation of the start-up education in universities.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.455-464
• /
• 2018

This study investigated whether the whitening effects of fullerene serum occurred through improvement of melanin production and skin tone and evaluated its potential for use as a cosmetic material for adult women aged 30-55 with dull skin color and pigmentation. Subjects were divided into a control group with fullerene-less serum (B) and an experimental group with serum containing 0.1% fullerene (A) and evaluated over 8 weeks. Visual assessment and measurement of skin conditions (melanin index, skin brightness) were conducted before use of and 4 and 8 weeks after use of the product, and a questionnaire survey and safety assessment were conducted at the end of the experiment. The results revealed that the highest decrease was 0.37% in the experimental group (A) after eight weeks of use of the product, but that this difference was not statistically significant. Moreover, no significant differences were observed upon inter-group comparison. Evaluation of changes in the melanin index and inter-group comparison revealed a significant decline in the experimental group (A) at all time points. Additionally, the $L^*$ value (skin brightness) of the experimental group (A) showed a significant increase (improvement) after eight weeks, while in inter-group comparison revealed a significant increase (improvement) at all time points (4 and 8 weeks later) (p<0.05). Based on a questionnaire survey of efficacy, positive response rates such as improvement of the target parts on week 8 were high in terms of 'improvement of skin color.' Moreover, the safety assessment revealed no adverse reactions. In conclusion, serum containing 0.1% fullerene revealed improved melanin production and skin tone (brightness) and confirmed its potential for use as a cosmetic material with brightening efficacy. Taken together, the results of this study indicate systematic investigation of the effective application and cosmetics formulations of this product are warranted.

• Journal of Food Hygiene and Safety
• /
• v.29 no.4
• /
• pp.347-355
• /
• 2014

In this study, the detection method was developed using molecular biological technique to distinguish authenticity of animal raw materials. The genes for distinction of species about animals targeted at Cytochrome c oxidase subunit I (COI), Cytochrome b (Cytb), and 16S ribosomal RNA (16S rRNA) genes in mitochondrial DNA. The species-specific primers were designed by that Polymerase Chain Reaction (PCR) product size was around 200 bp for applying to processed products. The target 24 raw materials were 2 species of domestic animals, 6 species of poultry, 2 species of freshwater fishes, 13 species of marine fishes and 1 species of crustaceans. The results of PCR for Rabbit, Fox, Pheasant, Domestic Pigeon, Rufous Turtle Dove, Quail, Tree Sparrow, Barn Swallow, Catfish, Mandarin Fish, Flying Fish, Mallotus villosus, Pacific Herring, Sand Lance, Japanese Anchovy, Small Yellow Croaker, Halibut, Jacopever, Skate Ray, Ray, File Fish, Sea Bass, Sea Urchin, and Lobster raw materials were confirmed 113 bp ~ 218 bp, respectively. Also, non-specific PCR products were not detected in compare species by species-specific primers. The method using primers developed in this study may be applied to distinguish an authenticity of food materials included animal raw materials for various processed products.