• Journal of Korea Foundry Society
• /
• v.13 no.4
• /
• pp.333-341
• /
• 1993

The effects of alloying elements on the structure and mechanical properties of compacted/vermicular graphite cast irons containing copper, tin and molubdenum for producing pearlite matrix, and also containing phosphorus and boron for increasing wear resistance, were investigated. The Brinell hardness and ultimate tensile strength of the specimens with the range of compositions, [1.5% Cu-0.05% Sn-(0.2-0.4)% Mo-(0.2-0.6)% P-(0.035-0.070)% B], was found to fall within in the following range, depending on their composition; Brinell hardness of BHN 250-315, ultimate tensile strength of $28.1-40.3kg/mm^2$. It was also found within this experiment that CV graphite cast irons possessing higher amount of phosphide eutectic exhibit better wear resistance, but the wear resistance became deteriorate when the area fraction of phosphide eutectics exceed more than 10%. From these experimental results, it could be concluded that the CV graphite cast iron containing 1.5% Cu, 0.05% Sn, 0.4% Mo, 0.2% P and 0.035% B showed good mechanical and wear resistance properties.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.201-207
• /
• 2020

With the expansion in the use of DC power systems and increased need for system maintenance, the development of measurement devices for maintenance requires high stability. Of the different kinds of DC current measurement devices, the single-shot measurement device causes the input signal of the current measuring unit to initially generate a high inrush current. The high inrush current flows into the signal processor of the meter, shortening the life of the internal fuses and causing failure. Therefore, in this study, the I²t value for increasing the durability of the fuse is designed using the available wire diameter. Operating characteristics for 210~400% over-current of the rated current, which is relatively low over-current, are realized by the plating of low melting tin metal. As a result, a method of designing a fuse element for a DC power supply, which improves the safety of the DC current measurement device by blocking the failure caused by the inrush current, is presented.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.6
• /
• pp.191-196
• /
• 2004

The measurement method is proposed for performance-evaluation of bus system in this paper. The cycle tin in manufacturing system that sensor and actuator play on the role is important factor for performance-evaluation. In order to measure cycle time, proposed method is based on simple algorithm. But it must consider delay elements in PLC and it's peripheral. The test of the cycle time is divided into the best case and the worst case and parameters are set corresponding to two cases for the improvement of measurement result It is shown that the proposed method is efficient by measuring the cycle time of the fieldbus basing on the mathematics model. As a result, due to simplicity and convenience of proposed method, the engineering cost and time demanding for test of cycling time can much reduce.

• Korean Journal of Metals and Materials
• /
• v.46 no.1
• /
• pp.26-32
• /
• 2008

Examination of two bronze vessels supposedly from the Koryo dynasty revealed that they consist of bowls and stands that are fixed together using rivet joints made of Cu-Ag alloys. The bowls and stands were forged out of unleaded bronze alloys of approximately 22 weight % Sn before being quenched from the ${\alpha}+{\beta}$ region of the Cu-Sn phase diagram. This specific alloy and the thermo-mechanical treatment constitute two key elements of the unique technical tradition called Bangcha (방짜) that has long been established in Korea. The high Sn content ensures better casting and the thermal treatment causes the brittle ${\delta}$ phase to be avoided in forging as well as in services. The experiment on the laboratory Cu-Ag alloys of varying Ag contents suggested that the Cu-Ag system was the best choice of materials for the rivets at the time in view of their color, availability, ductility and low melting points.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.471-480
• /
• 2022

Inductive power transfer (IPT) is an attractive power transmission solution that is already used in many applications. In the IPT system, optimal coil design is essential to achieve high power efficiency, but the effective design method is yet to be investigated. The inductance formula and finite element method (FEM) are popular means to link the coil geometric parameters and circuit parameters; however, the former lacks generality and accuracy, and the latter consumes much computation time. This study proposes a novel coil design method to achieve speed and generality without much loss of accuracy. By introducing one-turn permeance simulation in each FEM phase combined with curve fitting and optimization by MATLAB in the efficiency calculation phase, the iteration number of FEM can be considerably reduced, and the generality can be retained. The proposed method is verified through a 100 W IPT system experiment.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.09a
• /
• pp.261-278
• /
• 2003

Concepts.Wafer-Level Chip-Scale Concept with Handling Substrate.Low Accuracy Placement Layout with Isolation Trench.Possible Pitch of Interconnections down to $10{\mu}{\textrm}{m}$ (Sn-Grains).Wafer-to-Wafer Equipment Adjustment Accuracy meets this Request of Alignment Accuracy (+/-1.5 ${\mu}{\textrm}{m}$).Adjustment Accuracy of High-Speed Chip-to-Wafer Placement Equipment starts to meet this request.Face-to-Face Modular / SLID with Flipped Device Orientation.interchip Via / SLID with Non-Flipped Orientation SLID Technology Features.Demonstration with Copper / Tin-Alloy (SLID) and W-InterChip Vias (ICV).Combination of reliable processes for advanced concept - Filling of vias with W as standard wafer process sequence.No plug filling on stack level necessary.Simultanious formation of electrical and mechanical connection.No need for underfiller: large area contacts replace underfiller.Cu / Sn SLID layers $\leq$ $10{\mu}{\textrm}{m}$ in total are possible Electrical Results.Measurements of Three Layer Stacks on Daisy Chains with 240 Elements.2.5 Ohms per Chain Element.Contribution of Soldering Metal only in the Range of Milliohms.Soldering Contact Resistance ($0.43\Omega$) dominated by Contact Resistance of Barrier and Seed Layer.Tungsten Pin Contribution in the Range of 1 Ohm

• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.394-397
• /
• 2012

In this work, we studied the influence of the dopant elements concentration on the properties of SnO2 thin films deposited by pulsed laser deposition. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Hall effect measurement and UV-Vis studies were performed to characterize the deposited films. XRD results showed that the films had polycrystalline nature with tetragonal rutile structure. FE-SEM micrographs revealed that the as deposited films composed of dense microstructures with uniform grain size distribution. All the films show n-type conduction and the best transparent conductive oxide (TCO) performance was obtained on 6 wt% Sb2O5 doped SnO2 film prepared at pO2 of 60mtorr and Ts of 500 ℃. Its resitivity, optical transmittance, figure of merit are 7.8 × 10-4 Ω cm, 85% and 1.2 × 10-2 Ω-1, respectively.

• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.188-194
• /
• 1999

To investigate the effect of niobium and tin on the mechanical properties of zirconium alloys, the tensile test and the microstructural analysis were performed on the Zr-based binary(Zr-xNb, Zr-xSn) and ternary(Zr-0.8Sn-xNb, Zr-0.4Nb-xSn) alloys. As the content of Nb or Sn element increased, the strengths of the Zr-based alloys tended to gradually increase. The increase of mechanical strength was remarkable strength was remarkable in the range more than the solubility of Nb and Sn. The strengthening effects were discussed on the basis of the solid solution hardening, the precipitate hardening, the grain size effect, and the texture effect. The mechanical strength is mainly controlled by the solid solution hardening and additionally by the precipitate hardening in the content more than solubility limit of Nb and Sn. The grain refinement also has a slight effect on the strength of the zirconium alloys with the addition of Nb and Sn. However, the texture effect can be excluded due to the same Kearns number regardless of the content of alloying elements.

• Korean Journal of Heritage: History & Science
• /
• v.43 no.3
• /
• pp.102-121
• /
• 2010

Three bronze bells excavated from the Hoeamsa temple site were investigated for their microstructures and chemical compositions in an effort to understand the technology applied in fabrication, which may represent the related industry established in the early Joseon period. The result shows that the bells were cast from alloys of approximately 85% copper-8% tin-7% lead. The chemical analysis for ten trace elements shows that they were all kept below 0.3 weight %, suggesting that the alloys were made of relatively well-refined copper, tin and lead. The presence of sulfur and iron indicates that chalcopyrite or chalcocite may have been used in the smelting of copper. Evidence has been found that the bells were cast by pouring the liquid metal from the top of the sand molds that were set up in an upright position. No additional treatments, thermal or mechanical, other than a little grinding were applied upon the completion of casting. After the shaping process, a balancing plate was attached to the top of the bell using a steel connection ring. The connection assembly was then fixed to the main body by using molten bronze as a solder. The surface inscription was found carved using different techniques. The differences in the order of strokes and the calligraphic style indicate that the carving was carried out by more than one master. In the absence of documentary evidence on past bronze technology, the present bronze bells with known chronology, provenance and the main agent of production, prove to be a rare and valuable archaeological material for the understanding of the related technology in use in the early Joseon period.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.7
• /
• pp.87-93
• /
• 2014

TIn analysis as the first step of S/W development, security requirements of identification and authentication, ID and password management, authentication process, authentication method, ete. should be defined. Identification is to uniquely identify certain users and applications running on a certain system. Authentication means the function to determine true or false users and applications in some cases. This paper is to suggest the security requirements for identification and authentication in analysis step. Firstly, individual ID should be uniquely identified. The second element is to apply the length limitations, combination and periodic changes of passwords. The third should require the more reinforced authentication methods besides ID and passwords and satisfy the defined security elements on authentication process. In this paper, the security requirements for the step of identification and authentication have been explained through several practical implementation methods.