• Journal of the Ergonomics Society of Korea
• /
• v.30 no.1
• /
• pp.29-39
• /
• 2011

Safety management paradigm which against human errors in aviation industry is now changing from the follow-up measures after accident in the past to systematic approach that a forecast the hazards and improve the working system of the group to prevent accidents. As human factors are based on the man's specific psychological traits, it takes much time and efforts to prepare the preventive measures. That's why aviation industry is interested in the accident-prevent measurements against human errors. In this thesis, therefore, we are going to introduce the efforts that aviation organizations have tried and recommend management systems and discuss the suggestive facts. At first, we discussed introduction of HFACS which is the systematic accidents-classification system related to human errors in the aviation organization and countermeasure in the aspects of management, technology/engineering, education training. We described about FOQA, LOSA, CRM/TEM, aviation safety information DB in the aspect of management, and explained safety technologies that prevent human errors or avoid technologically when emergency occurs in the aspect of technology/engineering. In the aspect of education training, we explained the application plan about safety programs(LOFT/Simulator use, CRM/TEM application etc).

• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.57-66
• /
• 2001

In order to measure steel corrosion in mortar by a transient electro-magnetic (TEM) Method, the development of the sensors have been studied. The sensors were made of enamelled wire with diameter of 0.25mm and Acril. The sensor configuration was used as a coincident loop type. The secondary electro motive force(EMF) was measured with SIROTEM III. The accelerator was equipped with the SIROTEM III. The accelerator permits the transmitter to turn off approximately 10~15 times faster than normal. The high resolution time series used for very shallow or high resistivity investigation was selected. The steels were embedded in mortar which were made from sand : cement : water ratio of 2 : 1: 0.5. The mortar specimen was 50cm long, 20cm wide and 10cm thick. To investigate steel corrosion in mortar, the sensors used were with 2$\times$2$cm^2$(3, 6, 9$\Omega$), 3$\times$3$cm^2$(3, 6, 9$\Omega$) and 6$\times$6$cm^2$(3, 6, 9$\Omega$). The obtained result obtained showed that the sensor 8(6$\times$6$cm^2$, 6$\Omega$) was the proper sensor for the measurement of steel corrosion in mortar.

• Applied Microscopy
• /
• v.45 no.3
• /
• pp.183-188
• /
• 2015

Due to the miniaturization of semiconductor devices, their crystal structure on the nanoscale must be analyzed. However, scanning electron microscope-electron backscatter diffraction (EBSD) has a limitation of resolution in nanoscale and high-resolution electron microscopy (HREM) can be used to analyze restrictive local structural information. In this study, three-dimensional (3D) automated crystal orientation and phase mapping using transmission electron microscopy (TEM) (3D TEM-EBSD) was used to identify the crystal structure relationship between an epitaxially grown CdS interfacial layer and a $Cu(In_xGa_{x-1})Se_2$ (CIGS) solar cell layer. The 3D TEM-EBSD technique clearly defined the crystal orientation and phase of the epitaxially grown layers, making it useful for establishing the growth mechanism of functional nano-materials.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.252-261
• /
• 2020

We prepare ZnO nanoparticles by environmentally friendly synthesis using Cyathea nilgiriensis leaf extract. Various phytochemical constituents are identified through the assessment of ethanolic extract of plant Cyathea nilgiriensis holttum by GC-MS analysis. The formation of ZnO nanoparticles is confirmed by FT-IR, XRD, SEM-EDX, TEM, SAED and PSA analysis. TEM observation reveals that the biosynthesized ZnO nanopowder has a hexagonal structure. The calculated average crystallite size from the high intense plane of (1 0 1) is 29.11 nm. The particle size, determined by TEM analysis, is in good agreement with that obtained by XRD analysis. We confirm the formation of biomolecules in plant extract by FT-IR analysis and propose a possible formation mechanism of ZnO nanoparticles. Disc diffusion method is used for the analyses of antimicrobial activity of ZnO nanoparticles. The synthesized ZnO nanoparticles exhibit antimicrobial effect in disc diffusion experiments. The biosynthesized ZnO nanoparticles display good antibacterial performance against B. subtilis (Gram-positive bacteria) and K. pneumonia (Gram-negative bacteria). Bio-synthesized nanoparticles using green method are found to possess good antimicrobial performance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.1
• /
• pp.64-69
• /
• 2019

Methylammonium lead triiodide ($MAPbI_3$)-based perovskite solar cells potentially have potential advantages such as high efficiency and low-cost manufacturing procedures. However, $MAPbI_3$ is structurally unstable and has low phase-change temperatures ($30^{\circ}C$ and $130^{\circ}C$); it is necessary to solve these problems. We investigated the crystal structure and phase separation using real-time temperature-change X-ray diffraction, transmission electron microscopy, and electron energy loss spectroscopy. $MAPbI_3$ has a tetragonal structure, and at about $35^{\circ}C$ the c-axis contracts, transforming $MAPbI_3$ into the related cubic crystal structure. In addition, at $130^{\circ}C$, phase separation occurs in which $CH_3NH_2$ and HI at the center of the unit cell of the perovskite structure are extracted by gas, leavingand only $PbI_2$ of the three-component structure, is produced as the final solid product.

• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.921-926
• /
• 1994

The characteristics of gate oxide significantly depend on the last chemical solution used in cleaning process. The standard RCA, HF-last, SC1-last, and HF-only processes are the pre-gate oxide cleaning processes utilized in this experiment. Cleaning process was followed by thermal oxidation in oxidation furnace at $900^{\circ}C$. A 100$\AA$ gate oxide was grown and characterized with using lifetime detector, VPD AAS, SIMS, TEM, and AFM. The results of HF-last and HF-only were shown to be very effective to remove the metallic impurities. And these two splits also showed long minority carrier lifetimes. The surface and interface morphologies of the oxide were examined with AFM and TEM. The rough surface morphologies were observed with the cleaning splits containing the SC1 solution. The smooth surface and interface was observed with the HF-only cleaning process.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.37-42
• /
• 2000

The comparative study of texture of Al/Ti thin films deposited on low-dielectric polymer and $SiO_2$substrates has been investigated. Fifty-nm-thick Ti films and 500-nm-thick Al-1%Si-0.5%Cu (wt%) films were deposited sequentially onto low-k polymers and $SiO_2$by using a DC magnetron sputtering system. The texture of Al thin film was determined using X-ray diffraction (XRD) theta-2theta ($\theta$-2$\theta$) and rocking curve and the microstructure of Al/Ti films on low-k polymer and $SiO_2$substrates was characterized by cross-sectional transmission electron microscopy (TEM). Both the $\theta$-2$\theta$ method and rocking curve measurement suggest that Al/Ti thin films deposited on $SiO_2$have stronger texture than those deposited on low-k polymer. The texture of Al thin films strongly depended on that of Ti films. Cross-sectional TEM revealed that grains of Ti films on $SiO_2$substrates had grown perpendicular to the substrate, while the grains of Ti alms on SiLK substrates were formed randomly. The lower degree of (111) texture of Al thin films on low-k polymer was due to Ti underlayer.

• Korean Journal of Materials Research
• /
• v.7 no.8
• /
• pp.654-659
• /
• 1997

HMDS[Si$_{2}$(CH$_{3}$)$_{6}$]단일 선구체를 이용하여 화학증착 방법으로 성장된 3C-SiC/Si(001) 이종접합박막의 특성을 XRD, 라만 스펙트럼 및 투과전자현미경(TEM)등을 이용하여 조사하였으며 시판되고 있는 상용 3C-SiC/Si 시편을 같은 방법으로 분석하여 특성을 비교검토하였다. $C_{3}$H$_{8}$-SiH$_{4}$-H$_{2}$혼합가스를 선구체로 이용하여 5$\mu\textrm{m}$두께로 성장된 상용 3C-SiC/Si 이종접합박막 시료의 XRD스펙트럼에서는 강한 3C-SiC(002)피크 만이 관찰되었으며, 라만 스펙트럼의 LO피크는 970nm$^{-1}$ 정도에서 강하게 나타났다. TEM 관찰 결과 다수의 전위, 쌍정, 적층결함 및 APB와 같은 결정결함들이 3C-SiC/Si 계면 근처에 집중적으로 분포되어 있었으며 성장된 박막은 단결정임을 확인할 수 있었다. 선구체로 HMDS를 사용하여 0.3$\mu\textrm{m}$ 및 2$\mu\textrm{m}$ 두께로 성장시킨 3C-SiC/Si 박막 시료의 XRD 스펙트럼은 다소 완만한 3C-SiC(002) 피크와 함께 3C-SiC(111)피크가 관찰되었으며, TEM으로 확인한 결과 소경각 결정립들이 약 5˚-10˚ 정도 방위차를 가지고 성장하여 기둥구조(columnar structure)를 이루고 있기 때문임을 알 수 있었다. 라만 스펙트럼 분석 결과 박막의 LO 피크가 967-969nm$^{-1}$정도로 다소 낮은 wavenumber쪽으로 이동되어 박막 내에 상당한 응력이 존재함을 확인할 수 있었다. 이와 같은 HMDS 3C-SiC박막의 특성은 성장 온도가 낮고 박막 성장용 가스로 사용한 HMDS 선구체에서 탄소가 과잉으로 공급되기 때문으로 제안되었다.다.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.30 no.4
• /
• pp.405-411
• /
• 2020

Objectives: The objectives of this study were to investigate whether airborne fibers were released to the outside air from the asbestos removal area in buildings, and to confirm the existence of asbestos fibers in samples using transmission electron microscopy(TEM). Methods: A total of 1,295 samples was collected from inside and outside 155 asbestos removal areas. To investigate the release of asbestos fibers from the removal area, samples were collected at three locations, such as an entrance to change room, an exit of negative pressure unit(NPU) and perimeter areas. Samples were also collected in the removal area prior to and after removal activity. All samples were analyzed by phase contrast microscopy(PCM) and one-tenth of the samples was analyzed using TEM to discriminate asbestos fibers. Results: During the asbestos removal activity, 27(4.1%) of 662 samples collected outside the removal area showed airborne fiber concentrations equal to or in excess of 0.01 f/cc, the permissible emission standard of the Korean Ministry of Environment. Further, 111 samples were analyzed using TEM. The distribution of asbestos fiber concentrations was log-normal. It was found that 51 of 111 samples(46%) contained asbestos fibers. Conclusions: There is a potential risk of asbestos exposure among neighbors and the public outside the asbestos removal areas. It is recommended that the asbestos removal work be conducted strictly following the specifications required by government and/or professional organizations.

• Korean Journal of Microbiology
• /
• v.46 no.1
• /
• pp.38-45
• /
• 2010

The study performed to identify the type of ESBL against strains which are producing extendedspectrum ${\beta}$-lactamases and isolated from sewage in Suyeong sewage disposal plant, Busan Environmental Corporation. By the standard activated sludge method, Suyeong sewage disposal plant purify living and lavatory sewage gathering from the northeast Busan and the facility purify total 550,000 tons of living sewage disposal a day. 14 strains were isolated by double disk synergy test and the third generation cepha-antibiotics test. Indole, methyl-red, Voges-Proskauer, Simmon's citrate, decarboxylasedihydrolase and sugar-fermentation tests identified as Klebsiella pneumoniae (n=4) and Escherichia coli (n=10). Plasmid-mediated transmission test against isolated 14 strains proved 11 strains transmitted resistance to recipient E. coli J53 (sodium $azide^R$, $ceftazidime^S$). 9 strains of conjugant were expressed ESBL genes transferred from parental strain but 2 conjugants did not expressed. The type of ESBL from each strain was determined by isoelectric focusing points, DNA and amino acids sequencing. The results indicated that the types of ESBL transmitted to recipient E. coli J53 were TEM-1, the parental TEM type and SHV-12 type.