• Journal of IKEEE
• /
• v.20 no.4
• /
• pp.373-377
• /
• 2016

This paper presents a low power boost converter using offset controlled Zero Current Sensor (ZCS) control for thermoelectric energy harvesting.[1] [5] Offset controlled ZCS uses adjustable pre-offset that is controled by 6bit code each connected gate of NMOS for switching. Offset controlled ZCS demonstrates an efficiency that is higher than using analog comparator ZCS and that is smaller area than using delay line ZCS. Experimentally, the offset controlled ZCS system consumes 10 times less power than analog comparator ZCS based system at similar performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.15-19
• /
• 2011

We have proposed a maximum power point tracking (MPPT) circuit for thermoelectric generator (TEG) using a Boost converter. The key point of the proposed MPPT circuit is that the duty ratio of the boost converter automatically moves to Maximum Power Point by comparing of consecutive sampling voltage using two comparators. From the simulation results, we showed that the proposed circuit can find the maximum power point within 2 CLK periods and to generate optimal PWM signal within 3 CLK periods. The proposed MPPT circuit was designed by using a CMOS 0.18 um process, and it is now on the fabrication.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.7
• /
• pp.845-852
• /
• 2003

Liquid desiccant dehumidification system can be used effectively to save energy consumed in air conditioning as an alternative compared with conventional air conditioning systems by reducing latent heat load. The dehumidifier and the regenerator from the heart of this system. The latent part of the cooling load is handled using liquid desiccant. In this study, the experimental regenerator has been designed to study the regeneration characteristics of the aqueous triethylene glycol(TEG) system. The performance factors of the regenerator with finned tube heat exchanger were evaluated by a series of experimental runs. The regeneration process is highly dependent on the liquid desiccant conditions, such as, temperature, concentration and flow rate. In addition, the effects of the inlet air temperature, humidity and flow rate were discussed. Data obtained are useful for design guidance and performance analysis of a regenerator, particularly for a liquid desiccant cooling system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.10
• /
• pp.952-959
• /
• 2004

The hybrid liquid desiccant air conditioning system has been in use for many years, primarily in industrial process applications requiring dehumidification and humidity control. In this study, the hybrid dehumidifier has been designed to study the dehumidification characteristic of the aqueous triethylene glycol (TEG) solution. The experimental results show energy efficient characteristics of hybrid liquid desiccant air conditioning system compared with the refrigeration system in terms of energy use, the difference of pressure loss between hybrid liquid desiccant air conditioning system and refrigeration system. Data obtained are useful for design guidance and performance analysis of the hybrid air conditioning system.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.7
• /
• pp.630-638
• /
• 2004

Liquid desiccant dehumidification systems have the ability to provide efficient humidity and temperature control while saving the electrical energy requirement for air conditioning as compared to a conventional system. The dehumidifier and the regenerator form the heart of this system. The latent part of the cooling load is overcome using liquid desiccant. The model regenerator has been designed to study the absorption characteristic of the aqueous triethylene glycol (TEG) solution which is in the flow range from 20 to 50 LPM. Also, this system designed that was able to change the height of the regenerator and dehumidifier. Because the effect of performance have different result according the height. The effect of performance factors of the regenerator with inlet solution flow rate, air flow rate, solution concentration, solution temperature, brine temperature, air temperature and inlet air relative humidity have been analyzed. Data obtained are useful for design guidance and performance analysis of the hybrid air conditioning system.

• Journal of Veterinary Clinics
• /
• v.36 no.1
• /
• pp.42-45
• /
• 2019

Thromboelastography (TEG) analysis consists of ${\alpha}$, G, K, MA, and R types of values and tests the effectiveness of blood clotting, which can be assessed for platelet function, clotting strength, and fibrinolysis. Canine heartworm diseases caused by Dirofilaria immitis, a vascular nematode, can lead to hyperfibrinolysis and hypercoagulation. In this study, G and MA values showed a statistically significant decrease over time after treatment of heartworm disease. Additionally, the ${\alpha}-value$ showed a high correlation with G, K, MA, and R values. The G value showed a high correlation with K and MA values, while The K value showed a high correlation with MA and R values. This study clearly found a gradual decrease in G and MA values in dogs with heartworm disease over time, both before and after treatment. This suggests that the clot formation time is longer and that the intensity of clot formation is lowered and may improve the risk of thromboembolism in dogs with heartworm disease.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.220-233
• /
• 2019

This work aims to study and analyze the various operating modes of universal power converter which is powered by solar and thermoelectric generators. The proposed converter is operated in a DC-DC (buck or boost mode) and DC-AC (single phase) inverter with high efficiency. DC power sources, such as solar photovoltaic (SPV) panels, thermoelectric generators (TEGs), and Li-ion battery, are selected as input to the proposed converter according to the nominal output voltage available/generated by these sources. The mode of selection and output power regulation are achieved via control of the metal-oxide semiconductor field-effect transistor (MOSFET) switches in the converter through the modified stepped perturb and observe (MSPO) algorithm. The MSPO duty cycle control algorithm effectively converts the unregulated DC power from the SPV/TEG into regulated DC for storing energy in a Li-ion battery or directly driving a DC load. In this work, the proposed power sources and converter are mathematically modelled using the Scilab-Xcos Simulink tool. The hardware prototype is designed for 200 W rating with a dsPIC30F4011 digital controller. The various output parameters, such as voltage ripple, current ripple, switching losses, and converter efficiency, are analyzed, and the proposed converter with a control circuit operates the converter closely at 97% efficiency.

• The Journal of Internal Korean Medicine
• /
• v.31 no.2
• /
• pp.346-355
• /
• 2010

Objectives : This study was performed in order to investigate the anti-fibrogenic effect of Acer tegmentosum Maxim. on r at hepatic stellate cell line T6. Materials and Methods : Hepatic stellate Cells (T6) were treated with various concentrations of distilled water Acer teg mentosum Maxim. extract for 24, 48, 72 hours. After the treatment, cell viability, proliferation, procollagen levels, mRNA of AS MA, MMP-2, collagen type 1a2 and IL-6 production were measured using MTT assay, BrdU assay, RT-PCR, procollagen typ e 1 C-peptide EIA kit and murine IL-6 ELISA development kit. Results : Cell viability of HSC-T6 decreased significantly in both 24 hours and 48 hours groups in a dose-dependant man ner. Proliferation of HSC also decreased in the same way. In the RT-PCR, mRNA expression of collagen type 1a2 and ASMA decreased in the groups which were treated with Acer tegmentosum Maxim. for 24 hours. The production of procollagen tended to decrease in a dose-dependant manner in the 24 hours treated group. IL-6 production increased under Acer tegmentosum trea tment in a dose-dependant manner in both 24 and 48 hours groups. Conclusion : These results show the possibility that Acer tegmentosum Maxim. can be an effective remedy for liver fibrosi s and liver cirrhosis.

• Nuclear Engineering and Technology
• /
• v.52 no.1
• /
• pp.19-26
• /
• 2020

Small nuclear reactor features higher power capacity, longer operation life than conventional power sources. It could be an ideal alternative of existing power source applied for special equipment for terrestrial or underwater missions. In this paper, a 25kWe heat pipe cooled reactor power source applied for multiple use is preliminary designed. Based on the design, a thermal-hydraulic analysis code for heat pipe cooled reactor is developed to analyze steady and transient performance of the designed nuclear reactor. For reactor design, UN fuel with 65% enrichment and potassium heat pipes are adopted in the reactor core. Tungsten and LiH are adopted as radiation shield on both sides of the reactor core. The reactor is controlled by 6 control drums with B₄C neutron absorbers. Thermoelectric generator (TEG) converts fission heat into electricity. Cooling water removes waste heat out of the reactor. The thermal-hydraulic characteristics of heat pipes are simulated using thermal resistance network method. Thermal parameters of steady and transient conditions, such as the temperature distribution of every key components are obtained. Then the postulated reactor accidents for heat pipe cooled reactor, including power variation, single heat pipe failure and cooling channel blockage, are analyzed and evaluated. Results show that all the designed parameters satisfy the safety requirements. This work could provide reference to the design and application of the heat pipe cooled nuclear power source.

• Clean Technology
• /
• v.29 no.4
• /
• pp.255-261
• /
• 2023

Power semiconductors are semiconductors used for power conversion, transformation, distribution, and control. Recently, the global demand for high-voltage power semiconductors is increasing across various industrial fields, and optimization research on high-voltage IGBT components is urgently needed in these industries. For high-voltage IGBT development, setting the resistance value of the wafer and optimizing key unit processes are major variables in the electrical characteristics of the finished chip. Furthermore, the securing process and optimization of the technology to support high breakdown voltage is also important. Etching is a process of transferring the pattern of the mask circuit in the photolithography process to the wafer and removing unnecessary parts at the bottom of the photoresist film. Ion implantation is a process of injecting impurities along with thermal diffusion technology into the wafer substrate during the semiconductor manufacturing process. This process helps achieve a certain conductivity. In this study, dry etching and wet etching were controlled during field ring etching, which is an important process for forming a ring structure that supports the 3.3 kV breakdown voltage of IGBT, in order to analyze four conditions and form a stable body junction depth to secure the breakdown voltage. The field ring ion implantation process was optimized based on the TEG design by dividing it into four conditions. The wet etching 1-step method was advantageous in terms of process and work efficiency, and the ring pattern ion implantation conditions showed a doping concentration of 9.0E13 and an energy of 120 keV. The p-ion implantation conditions were optimized at a doping concentration of 6.5E13 and an energy of 80 keV, and the p+ ion implantation conditions were optimized at a doping concentration of 3.0E15 and an energy of 160 keV.