• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.261-264
• /
• 2002

Interfacial evaluation, damage sensing and cure monitoring of single carbon fiber/thermosetting composite with different curing processes was investigated using electro-micromechanical test. After curing, residual stress was monitored by measurement of electrical resistance (ER) and then it was compared to correlate with various curing processes. In thermal curing, curing shrinkage appeared significantly by matrix shrinkage and residual stress due to the difference in thermal expansion coefficient (TEC). The change in electrical resistance (ΔR) on thermal curing was higher than that on ultraviolet (UV) curing. For thermal curing, apparent modulus was the highest and reaching time until same strain was faster. So far thermal curing shows strong durability on the IFSS after boiling test.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.109-113
• /
• 2002

Interfacial and electrical properties for the carbon fiber reinforced epoxy-amine terminated (AT) PEI composites were performed using microdroplet test and electrical resistance measurements. As AT PEI content increased, the fracture toughness of epoxy-AT PEI matrix increased, and IFSS was improved due to the improved toughness and energy absorption mechanisms of AT PEI. The microdroplet in the carbon fiber/neat epoxy composite showed brittle microfailure mode. At 15 wt% AT PEI content, ductile microfailure mode appeared because of improved fracture toughness. After curing, the changes of electrical resistance (ΔR) with increasing AT PEI content increased gradually because of thermal shrinkage. The matrix fracture toughness was correlated to IFSS, TEC and electrical resistance. In cyclic strain test, the maximum stress and their slope of the neat epoxy case were higher than those of 15 wt% AT PEI. The results obtained from electrical resistance measurements under curing process and reversible stress and strain were consistent well with matrix toughness properties.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.644-647
• /
• 2004

Optical add/drop multiplexers (OADMs), one of the new network elements, will play a key role enabling greater connectivity and flexibility in the dense wavelength-division multiplexing (DWDM) networks. The importance of OADMs is that they allow the optical network to be local transmitting/extraction on a wavelength-by-wavelength basis to optimize traffic, efficient network utilization, network growth, and to enhance network flexibility. Also, the automatic assembly system of micro optical filters and fibers is a key technology in the development of optical modules with high functionality. Recently, one of remarkable tends in the development of optical communication industry is the miniaturization and integration of products. In this research, we have developed a system capable of automatic alignment of a film filter and a lensed fiber in order to improve the speed and losses in the optical fiber to filter alignment of optical modules. Using the developed automatic alignment system and silicon optical benches, we have fabricated the micro OADM and measured the insertion loss and aging effect.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.212-215
• /
• 2002

Interfacial evaluation and damage sensing of the carbon fiber/epoxy-amine terminated (AT)-polyetherimide (PEI) composites were performed using micromechanical test and electrical resistance measurement. As AT-PEI content increased, the fracture toughness of epoxy-AT-PEI matrix increased, and thus their interfacial shear strength (IFSS) was improved due to the improved toughness. After curing process, the changes in electrical resistance (ΔR) with increasing AT-PEI contents increased gradually because of the changes in thermal expansion coefficient (TEC) and thermal shrinkage of matrix. Matrix fracture toughness was correlated to the IFSS, residual stress and electrical resistance. The results obtained from the electrical resistance measurement during curing process, reversible stress/strain, and durability test were consistent with modified matrix toughness properties.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 봄 학술발표회 논문집
• /
• pp.214-217
• /
• 2003

In recent years the focus of research in dye chemistry has largely changed from involvement in the traditional chemistry of dyes and pigments to investigations of functional dyes. With the development of the elcetronics and information industries, the importance of functional dyes has increased. Many research papers have been published concerning new synthetic methods and mechanicsm of functional dyes. Highly functionalized dicyanopyrazine derivatives can be used as fluorescent dyestuffs, emitters for electroluminescent devices tec. (omitted)

• 한국광학회지
• /
• 제26권6호
• /
• pp.306-311
• /
• 2015

본 논문은 폴리머 광 도파로 기반의 브라그 격자(Polymer waveguide Bragg grating: PWBG) 파장 필터를 광섬유 레이저 공진기 내부에 삽입하여 단일 파장 가변 레이저를 구현하고, 주위 온도 및 공진기 내부의 편광 상태의 변화에 대한 출력 특성을 연구한 결과에 대해 보고한다. 레이저 공진기 내부에 있는 PWBG 파장 필터에 0 mW에서 100 mW의 전력을 인가해 주었을 때 레이저에서 발진하는 파장은 1548.24 nm에서 1531.95 nm까지 약 16.29 nm를 가변할 수 있었으며, 이 때 slope efficiency는 약 -0.16 nm/mW였다. 레이저 공진기 안의 편광을 적절하게 조절하면 모든 파장 가변 범위에서 35 dB 이상의 SMSR(side mode suppression ratio)을 얻을 수 있었다. 레이저 공진기 외부의 온도가 변화하면 발진하는 파장이 변하는 것을 알 수 있었다. 따라서 PWBG 파장 필터를 이용하여 안정된 파장 가변 레이저를 구현하기 위해서는 PWBG 파장 필터의 온도 안정화가 필요하며, 또한 편광에 대한 영향을 최소화하기 위해서는 레이저 공진기를 편광유지 광섬유로 구성해야 한다.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1991년도 춘계 총회 및 학술발표회
• /
• pp.9-9
• /
• 1991

This paper will begin by describing osmosis and how reverse osmosis works. It will show how osmotic pressure affects reverse osmosis operations. It uill explain salt rejection, membrane flux, and recovery rates and the affect that salt built up has on membrane performance. It wil 1 explain the limitations of RO performance and why pretreatment is important. It will describe the two basic types of membrane, asymmetric and thin-film composite and explain the difference between these types plus compare cellulose acetate types to aromatic polyamide type membranes. It will discuss operating efficiences as it compares to feedwater pressure, concentration, temperature and pH. Finally, it will discuss the differences between tubular, plate and frame, hollow fiber and spiral wound element design. It will be a paper that talks about the basics of RO systems and should give a person who is unfamiliar with RO a basic introduction to this type of separation technology.

• 한국광학회지
• /
• 제16권3호
• /
• pp.254-260
• /
• 2005

높은 재현성과 함께 효율적인 수동 정렬을 위하여 제안된 대형코어 단일모드 폴리머 광도파로를 이용하여 제작 가능한 폴리머 광도파로 소자인 가변 광감쇠기를 제안하고 삼차원 빔전파 방법을 이용하여 소자의 동작 특성을 파악하고 최적 구조를 설계하였다. 소자의 표면에 집적된 박막 전극 히터에서 발생하는 열로 인해 폴리머 광도파로에서 발생하는 굴절률 분포 변화를 수치해석적으로 구하였으며 이 결과를 이용하여 삼차원 빔전파 해석을 수행하였다. 대형코어 광도파로가 가지는 작은 굴절률 대비로 인해 효과적인 광감쇠 현상을 작은 온도 변화로부터 얻을 수 있음을 확인하였다. 일반 광도파로 VOA에서 섭씨 150도 이상의 온도 변화가 필요한 반면 대형 코아 광도파로 VOA는 섭씨 70도 정도의 온도 변화 만으로도 20 dB 이상의 감쇠를 얻을 수 있었다. 대형코아 광도파로가 가지는 장점인 높은 정렬오차 허용범위와 더불어 낮은 구동전압으로 동작하는 장점을 함께 가지는 가변 광감쇠기 설계를 완성하였다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제20권7호
• /
• pp.1067-1075
• /
• 2007

Twenty eight 3-4 month old castrated Black Bengal kids (Capra hircus) were used to determine the effects of source and level of dietary copper (Cu) concentration on their performance and nutrient utilization. Cu was supplemented (0, 10, 20 and 30 mg/kg diet DM) as copper sulfate ($CuSO_4$, $5H_2O$) or copper proteinate (Cu-P). Kids were fed a basal diet containing maize (19.5%), soybean (17.0%), deoiled rice bran (56.5%), molasses (4.0%), di-calcium phosphate and salt (1.0% each) and mineral and vitamin mixture (0.5% each) supplements at 3.5% of body weight to meet NRC (1981) requirements for protein, energy, macro minerals and micro minerals, excluding Cu. The basal diet contained 5.7 mg Cu/kg, 122.5 mg Fe/kg, 110 mg Zn/kg, 0.26 mg Mo/kg and 0.32% S. $CuSO_4$ or Cu-P was added to the basal diet at the rate of 10, 20 and 30 mg/kg. Kids were housed in a well ventilated shed with facilities for individual feeding in aluminum plated metabolic cages. Blood samples were collected from the jugular vein on d 0, 30, 60 and 90 to determine hemoglobin (Hb), packed cell volume (PCV), total erythrocyte count (TEC), total leukocyte count (TLC) and serum enzymes (alkaline phosphatase, alanine transferase and aspertate transferase). A metabolism trial of 6 days duration was conducted after 90 days of experimental feeding. Statistical analysis revealed that source and level of Cu supplementation improved live weight gain (p<0.04) and average daily gain (p<0.01). No significant contribution of source and level of Cu to alter serum serum enzymes was evident. Goats fed Cu-P tended to have higher Hb, PCV and TEC than with $CuSO_4$ supplementation. Cu-P increased digestibility of ether extract (EE, p<0.02) and crude fiber (p<0.05) and showed an increasing trend (p<0.09) for digested crude protein (CP) and crude fiber (CF). Supplemental dose of Cu linearly improved (p<0.02) digestibilities of dry matter (DM), organic matter (OM), EE and nitrogen free extract (NFE). Though the absorption of nitrogen (N) was not affected (p>0.10) by both source and dose of Cu, N retention was affected (p<0.04) and there was a significant $Source{\times}Dose$ interaction (p<0.05). Final body weight (BW) was not influenced (p>0.10) by the source of Cu but increasing dose of Cu increased (p<0.04) the BW of kids. TDN intake (g/kg $W^{0.75}$) was higher (p<0.05) with the increased dose of Cu and there was a significant $Source{\times}Dose$ interaction. It was concluded that supplementation of Cu from different sources and varying dose level in a concentrate based diet may improve performance, nutrient utilization and plane of nutrition in castrated Black Bengal kids. The effects on performance and nutrient utilization are more pronounced with Cu-P than $CuSO_4$ supplementation. Higher dose of Cu showed better result than lower dose.

• 비파괴검사학회지
• /
• 제27권4호
• /
• pp.299-304
• /
• 2007

구조물의 주요 부재들은 임의의 부분에 과대 하중이 작용하거나 반복 하중을 받아서 재료가 열화되면 균열이 발생한다. 이러한 균열은 구조물의 안전성을 평가할 수 있는 중요한 인자이며 균열의 진전 여부가 구조물의 안전성을 평가하기 위한 중요한 지표로 사용할 수 있다. 따라서 본 연구에서는 구조물의 기존 균열이 진전하는지를 감시하기 위하여 광섬유 브래그 격자 센서를 개발하였다. 이 센서 시스템은 탐촉자, 파장제어 광원부 및 광수신부, 그리고 가진부로 구성된다. 센서 탐촉자 부분은 광섬유 브래그 격자 소자만으로 구성된다. 파장제어 광원부는 전류공급회로와 DFB(distributed feedback) 레이저 다이오드로 구성되고 파장 제어 회로는 레이저 다이오드의 온도를 바꾸어 파장을 제어한다. 또한 가진부는 강체 낙하구에 의하여 구현한다. 이렇게 구성된 센서의 성능은 알루미늄판에 임의의 균열을 만들고 센서를 작동시키면서 출력 신호를 검토하면서 확인하였다. 광섬유 브래그 격자 센서의 출력 신호의 변화는 균열 길이 변화에 따라서 크게 변화되어 나타나므로 균열 진전 탐지 가능성이 충분함을 확인할 수 있었다.