• Journal of the Korean Ceramic Society
• /
• v.19 no.2
• /
• pp.115-120
• /
• 1982

The main objective of this work was to study the efTect of pressed density of pellets prepared from an oxide powder on their fired density and to prove experimentally the parabolic relationship proposed by FORD. A-I6 and A-J7 alumina powders. which showed quite dlfrerent powder characteristics but were essentially very reactive powders, were employed, and a series of pelIets weIe pressed in a 1l.2mm diameter hardened steel die with a hydraulic press and a mechanically operated press in order to obtain a wide range of pressed demity. Density ranges from 35 to 65 % theoretical for A-16, and 46 to 66 % theoretical far A-17 were obtained and the highest pressed density achieved using lubricant was 67.8 % theoretical. CompactlOn mechanisms for A-16 and A-I 7 were deduced. Several plots of ($D_F$-$D_P$) against DpjDT showed reasonable parabola and temperature dependence and the maximum density increase occurred when the pressed density was approximately 50% theoretical. The parabolic relationship was confirmed by linear plot of ($D_F$-$D_P$) against (1-$\frac{D_P}{D_T})$).

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.5 no.2
• /
• pp.8-14
• /
• 1968

A linear current-pulse discriminator consisting: of a transistor monostable multivibrator and a Si tunnel diode is described. The input currant pulse range is about 50$\mu$A~5.23mA. The measured maximum linearity deviation is $\pm$0.75% in the input current pulse range mentioned above. The pulse resolving ability of the discriminator measured depends upon the bias current through the T, D. ; and, under the reverse bias current of 3mA, the resolving time is 2rs if allow the excess pulse amplitude of 5%. The threshold stability of the discriminator depends mainly upon the stability of the peak current Ip of the T. D. ; and, under the ambient temperature variation from $0^{\circ}C$ to 5$0^{\circ}C$, no bigger threshold variation than the maximum linearity deviation, i. e. $\pm$ 0.75%, was observed.

• ETRI Journal
• /
• v.30 no.4
• /
• pp.526-534
• /
• 2008

This paper presents a fully integrated 0.13 ${\mu}m$ CMOS MB-OFDM UWB transmitter chain (mode 1). The proposed transmitter consists of a low-pass filter, a variable gain amplifier, a voltage-to-current converter, an I/Q up-mixer, a differential-to-single-ended converter, a driver amplifier, and a transmit/receive (T/R) switch. The proposed T/R switch shows an insertion loss of less than 1.5 dB and a Tx/Rx port isolation of more than 27 dB over a 3 GHz to 5 GHz frequency range. All RF/analog circuits have been designed to achieve high linearity and wide bandwidth. The proposed transmitter is implemented using IBM 0.13 ${\mu}m$ CMOS technology. The fabricated transmitter shows a -3 dB bandwidth of 550 MHz at each sub-band center frequency with gain flatness less than 1.5 dB. It also shows a power gain of 0.5 dB, a maximum output power level of 0 dBm, and output IP3 of +9.3 dBm. It consumes a total of 54 mA from a 1.5 V supply.

• Korean Journal of Veterinary Research
• /
• v.32 no.2
• /
• pp.165-173
• /
• 1992

The present study was carried out to investigate the effects of dopaminergic drugs and the role of specific dopamine(DA) receptors on the release of TSH, $T_4$ and $T_3$. Serum TSH levels (cold-induced, $4{^{\circ}C}$) were determined using RIA(radioimmunoassay) at 30 min after administration of dopamine agonists and antagonists. Serum $T_4$ and $T_3$ levels were detected after these dopaminergic drugs were administered subcutaneously twice a day for a week. The results of the study are summarized as follows : Apomorphine, a nonspecific DA receptor agonist, produced a dose-depedent decrease in serum TSH, $T_4$ and $T_3$ levels. However, only low doses (0.3, 1.0mg/kg) of SKF38393, a specific $D_1$-receptor agonist, produced a decrease in serum lelvels of TSH. I,Y171555, a specific $D_2$-receptor agonist, produced a dose dependent decrease in serum TSH, $T_4$ and $T_3$ levels. However, SCH23390, a specific $D_1$-receptor antagonist, produced a decrease except in serum T levels which were increased dose dependently. High doses (1.0, 3.0mg/kg) of sulpiride, a specific $D_2$-receptor antagonist, made a increase in the serum levels of TSH and $T_3$. The effects of dopaminergic drugs in serum TSH and $T_4$ levels was potentiated by the pretreatment of apomorphine. The overall results of this study suggest that the regulation of TSH, $T_4$ and $T_3$ secretion were mediated via specific $D_1$ and $D_2$ receptor.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1311-1313
• /
• 2006

Stereoscopic/autostereoscopic systems have been developed in order to express true 3D images, but have never had great success in the practical use. In order to apply 3D display to promising applications such as advertisements and games, we've developed a 42" 2D/3D switchable display. It has characteristics that don't require special glasses for 3D images, use multi-view technology for improving 3D viewing characteristics, and has a 2D/3D switching function to express dynamic 3D contents as well as conventional 2D contents.

• Korean Business Review
• /
• v.5
• /
• pp.241-274
• /
• 1992

General American English(=A.E.) has conservative elements as well as progressive elements. A.E. and B.E. are languages which have more similarities than differances. In this paper. I studied the process of English progress before the A.E. had come into being, and the historical background and the cahristics of A.E. coming into being. Considering the differences between A.E. and B.E. from spelling, pronunciation, vocabulary and grammar, I can give the outline as follows. A spelling 1. B.E. : au, ou $${\rightarrow}$$A.E. : a, o 2. B.E. : e $${\rightarrow}$$A.E. : i 3. B.E. : $${\ae}$$ oe $${\rightarrow}$$A.E. : e 4. B.E. : our $${\rightarrow}$$A.E. : or 5. B.E. : re $${\rightarrow}$$A.E. : er B. pronunciation 1. B.E. : [e] $${\rightarrow}$$A.E. : [i], [e], $$[\partial]$$ 2. B.E. : [a] $${\rightarrow}$$A.E. : 3. B.E. : [i(:)] $${\rightarrow}$$A.E. : [ai], $$[\partial]$$, $$[{\varepsilon}]$$ 4. B.E. : $$[{\ae}]$$ $${\rightarrow}$$A.E. : [e], [c] 5. B.E. : [ai] $${\rightarrow}$$A.E. : $$[{\ae}]$$, [e] 6. B.E. : [c] $${\rightarrow}$$A.E. : [e], [a], [o] 7. In case of "Vowel+[t]+Vowel", [t] is pronounced into [d] or [r] 8. In case of "-nt", [t] becomes a mute. 9. [t]+[j, l, m, n, r, u, or, w] $${\rightarrow}$$A.E. : [?] (=glottal stop) 10. B.E. : [w] $${\rightarrow}$$A.E. : [hw] 11. B.E. : [Voiceless consonants], [Voiced consonants] $${\leftarrow}$$A.E. : [Voiced consonants], [Voiceless consonants] C. Vocabulary The historical background and geographical conditions of those days caused lots of new compounds and neologies. D. Grammar Though we use "of" to indicate the possessive case of inanimate object, -s genitive is used in A.E. In the perfect tense, "have" is often omitted and also auxiliary verb "will" is used in any case

• Journal of Korea Multimedia Society
• /
• v.6 no.4
• /
• pp.658-667
• /
• 2003

Developing tailor made Multimedia courseware ensuring effective implementation of instruction strategies is a challenge that manifests in myriad problems of software design and coding. In this paper an attempt has been made to analyse and identify coding and implementation problems, in the backdrop of using two different multimedia software development tools i.e. Visual Basic and Toolbook, which underpin the development and effectiveness of use of multimedia courseware. Solutions to such problems have been discussed in context of Tool book. The examples presented in this paper are based on the experience of designing and implementation of two large scale professional quality Multimedia courseware development projects.

• Journal of the Korean Society of Safety
• /
• v.8 no.4
• /
• pp.27-40
• /
• 1993

High temperature tensile tests, steady state creep tests, Internal stress tests and creep rupture tests using A17075 alloy( $T_{6}$ ) were performed over the temperature range of 9$0^{\circ}C$~50$0^{\circ}C$ (0.4 $T_{m}$ ~0.85 $T_{m}$ ) and stress range of 0.64~17.2(kgf/$\textrm{mm}^2$). The main results obtained in this paper were as follows. (1) The activation energies for yielding at the temperature of 0.4 $T_{m}$ ~0.75 $T_{m}$ were calculated to be 25.7~36.5kcal/mol, which were nearly equal to the activation energies for creep. (2) At around the temperature of 9$0^{\circ}C$~12$0^{\circ}C$ and under the stress level of 10~17.2(kgf/$\textrm{mm}^2$), and at around the temperature of 200~41$0^{\circ}C$ and under the stress level of 1.53~9.55(kgf/$\textrm{mm}^2$) and again at around the temperature of 470~50$0^{\circ}C$ and under the stress level of 0.62~l.02(kgf/$\textrm{mm}^2$), the applied stress dependence of steady state creep rate $n_{measu}$ measured were, respectively, 3.15, 6.62 and 1.1, which were in good agreement the calculated stress dependence $n_{ealeu}$ obtained by the difference of the applied stress dependence of the Internal stress and the ratio of the internal stress to the applied stress. (3) At the temperature range of 0.4~0.43 $T_{m}$ , and at the temperature range of 0.52~0.75 $T_{m}$ and again at the temperature range of 0.82~0.85 $T_{m}$ , the activation energies $Q_{measu}$ obtained by steady state creep rate, respective, 26. 16, 34.9, 36.2 and 36.1kcal/mol, which were in good agreement with those obtained with the activation energies under constant effective stress and the temperature dependence of Internal stress. (4) At the temperature range of the 0.52~0.73 $T_{m}$ and under the stress level of 1.53~9.55(kgf/$\textrm{mm}^2$), the stress dependence of rupture life(n’) measured was 6.3~6.6, which was in good agreement with the stress dependence of steady state creep rate(n). And at the same condition the activation energy for rupture( $Q_{f}$ ) measured was 32.0~36.9kca1/mol, which was also in good agreement with the activation energy obtained by steady state creep rate ( $Q_{c}$ ). (5) The rupture life( $t_{f}$ ) might be represented by athermal process attributed to the difference of the applied stress dependence of the internal stress and the ratio of the internal stress to the applied stress, and the thermal activated process attributied to the temperature dependence of the internal stress as $t_{f}$ = A'$\sigma$$_{a}$ ｛n(1-d $\sigma$$_{i}$ /d $\sigma$$_{a}$ )/(1-$\sigma$$_{i}$ / $\sigma$$_{a}$ )｝.exp[｛ $Q_{c}$ $^{*}$-( $n_{o}$ R $T^2$/ $E_{(T)}$) (d $E_{(T)}$/dT) - ( $n_{0}$ R $T^2$/ $\sigma$$_{a}$ - $\sigma$$_{i}$ ) (d $\sigma$$_{i}$ /dT)｝/RT]. (6) The relationship betwween Larson-Miller rupture parameter and logarithmic stress was linearly decreased, so creep rupture life of Al 7075 alloy seemed to be predicted exactly with Larson-Miller parameter.meter.

• IMMUNE NETWORK
• /
• v.16 no.5
• /
• pp.281-285
• /
• 2016

CD4⁺ regulatory T cells (Tregs) are essential for normal immune surveillance, and their dysfunction can lead to the development of autoimmune diseases, such as type-1 diabetes (T1D). T1D is a T cell-mediated autoimmune disease characterized by islet b cell destruction, hypoinsulinemia, and severely altered glucose homeostasis. Tregs play a critical role in the development of T1D and participate in peripheral tolerance. Pluripotent stem cells (PSCs) can be utilized to obtain a renewable source of healthy Tregs to treat T1D as they have the ability to produce almost all cell types in the body, including Tregs. However, the right conditions for the development of antigen (Ag)-specific Tregs from PSCs (i.e., PSC-Tregs) remain undefined, especially molecular mechanisms that direct differentiation of such Tregs. Auto Ag-specific PSC-Tregs can be programmed to be tissue-associated and infiltrate to local inflamed tissue (e.g., islets) to suppress autoimmune responses after adoptive transfer, thereby avoiding potential overall immunosuppression from non-specific Tregs. Developing auto Ag-specific PSC-Tregs can reduce overall immunosuppression after adoptive transfer by accumulating inflamed islets, which drives forward the use of therapeutic PSC-Tregs for cell-based therapies in T1D.

• Proceedings of the KSAR Conference
• /
• 2002.06a
• /
• pp.81-81
• /
• 2002

The deer was inseminated at the breeding season, which only shows appearance of the estrus cycles. Early diagnosis of pregnancy is very useful to select non-pregnant does and also very important to decide re-inseminations or mating for producing of calves. Therefore, for the development of techniques on the early diagnosis of pregnancy of deer, the results of this study were summarized as following. (omitted)