• 한국강구조학회 논문집
• /
• 제23권2호
• /
• pp.169-177
• /
• 2011

본 논문은 반복하중을 받는 고강도강 원형강관의 T형 접합부의 면내 휨모멘트 내력에 대해 체계적으로 수행된 유한요소 해석으로부터 얻은 결과를 제시하고 있다. 용접된 원형강관의 T형 접합부의 회전강성 및 이에 따른 파괴모드를 분석하기 위하여 T형 접합부의 3차원 비선형 유한요소모델을 이용하였다. 주관과 지관의 세장비, 주관과 지관의 지름비와 같은 기하학적 파라미터 및 항복비 등에 따른 T형 접합부의 다양한 구조적 거동을 제시하였으며, 또한 주관의 압축응력의 크기에 따른 T형 접합부의 극한 면내 휨모멘트 내력의 변화를 분석하였다.

• 한국강구조학회 논문집
• /
• 제8권3호통권28호
• /
• pp.35-45
• /
• 1996

The purpose of this paper is to investigate experimentally the strength and deformation of T-joints to improve the structural behavior of truss connection consisted in square hollow steel section. There are two-types to be changed in T-joint shape. One type is TP-series that a brace member is rotated to 45 degree, another type is TR-series that a chord member is rotated to 45 degree. The most important results obtained from the 2nd experiment on the T-joints is as follow; The yielding strength and initial stiffness of TP-series increase more than a current type(TS-series) in $0.6{\leq}{\beta}(d/D){\leq}0.7(0.85{\leq}{\beta}$'$(={\sqrt2}{\cdot}{\beta}){\leq}1.0)$.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.528-533
• /
• 2002

The mechanical and metallurgical properties of friction welded joints type 5052 Al alloy/A36 steel have been studied in this paper. The joint strength increased with increasing upset pressure and friction time till it reached the critical value. The joint strength was fixed at low strength compare to that of base metal in the case of increasing friction time. Microstructure of 5052 Al alloy was greatly deformed near the weld interface. The very fine and equaxied grain structure was observed at the near interface. The elongated grain was formed outside dynamic recrystallizatoin region at the peripheral part, while the A36 steel' side was not deformed. The hardness of the near interface was slightly softer than that of 5052 Al alloy base metal. The maximum softening width was about 8mm from the interface. In the present work, the friction welding condition, t$_1$=0.5sec, P$_2$=137.5MPa, showed a maximum joint strength (202MPa) when friction pressure, upset time and rotation speed were fixed at 75MPa, 5sec, 2000rev/min and these were the optimum friction welding condition of 5052Al/A36 steel joints.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.192-194
• /
• 2005

Joint strength of spot friction welded 5J32 Al alloy were investigated according to the tool shape and the tool penetration depth. General spot friction stir welding tool consists of a shoulder having bigger diameter and a threaded pin projected from the shoulder, which resulted in the generation of large up-lifting of upper plate around the weld nugget because of the deeper penetration and the severe stirring effect of threaded pin. Two kinds of welding tools without the threaded pin were used to avoid the distortion and improve the joint strength. One was a simple cylindrical shape and the other was cylindrical shape with small projection. Therefore, the process was named as spot friction welding comparing to spot friction stir welding because spot friction welding don't use a stirring effect. Using the cylindrical shape tool with small projection, the up-lifting of upper plate were avoided and joint strength were superior to that of the joint using simple cylindrical shape tool. At the 0.5mm of too penetration depth using cylindrical tool with small projection, nugget pull fracture mode can be observed and shear fracture mode were dominant at the rest conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권2호
• /
• pp.135-143
• /
• 2013

마찰교반용접은 운송 분야 등에서 널리 상업화되고 있다. 본 연구는 마찰교반용접된 A2024-T4 합금의 결함을 비파괴검사(방사선투과검사, 초음파탐상시험, 전기전도도시험)와 파괴시험(인장강도 및 미세조직 관찰)을 실시하여 관찰하였다. 실험 결과 결함 분포도를 얻을 수 있었다. 방사선투과검사에서 발견되지 않은 미세결함이 초음파탐상시험에서는 발견되었으며, 초음파탐상시험은 음압의 차이와 그에 대응하는 색에 의해 결함의 정도를 검사할 수 있는 효과적인 방법이었다. 또한 전기전도도 측정값은 결함의 양이 많아짐에 따라 감소하는 경향을 보였다. 비파괴검사와 파괴검사를 통해 얻은 가장 건전한 조건의 이음 효율은 91% 이었다. 따라서 비파괴검사는 마찰교반용접된 A2024-T4 합금을 검사하는데 있어서 효과적인 방법이라 사료된다.

• 한국가스학회지
• /
• 제17권1호
• /
• pp.19-25
• /
• 2013

용접에 의한 가스설비, 교량, 선박 등 강 구조물의 접합 방법은 대부분 십자형이나 T형의 필릿 용접으로 이루어지며 구조물의 형상과 용도에 따라 완전 용입 또는 불완전 용입 상태로 이루어진다. 본 연구에서는 십자형 필릿용접 구조물에 대하여 재료 두께별 용입 깊이에 따른 피로 균열 특성을 파악하였고, 그 결과로부터 무한수명 영역내에서의 안전 설계응력에 대하여 고찰하였다. 미 용입 길이가 길면 루트 부 파괴가 되어 무한 수명 영역은 작고 미 용입 길이가 짧으면 토우부 파괴가 되어 무한 수명 영역은 크게 나타났다. 3층 용접한 재료 두께 20mm의 경우가 2층 용접한 재료 두께 10mm, 15mm의 경우보다 미세한 페라이트 침상 조직을 더 많게 형성시켜 노치 인성을 증가시키므로 서 피로강도와 무한 수명을 더 향상시킨 것으로 나타났다.

• 전산구조공학
• /
• 제5권3호
• /
• pp.97-103
• /
• 1992

철도, 항공 및 기계구조물등의 많은 설계문제에서는 반복하중의 영향을 받기 때문에 제조와 품질제어 공정에서 특히, 반복하중의 영향이 심한 구조부품의 피로균열에 대한 연구가 충분히 선행되어야 한다. Paris법칙에서 응력확대계수범위 .DELTA.K에 10%오차를 수반하면 피로수명 N에는 50%정도의 오차를 초래할 만큼 민감도가 매우 크다. 그러나, 선형탄성파괴역학에 근거한 p-version 유한요소법은 응력확대계수를 산정하는데 있어서 종래의 h-version 유한요소법에 비해 훨씬 적합함이 증명되고 있다. 제안된 해석법의 효율성을 입증하기 위해 철도차량의 연결접합부에 있는 T-joint부위의 피로균열해석과 원공이 있는 유한판의 원공주위에서 발생되는 균열해석이 수행되었다.

• 대한조선학회논문집
• /
• 제28권2호
• /
• pp.275-284
• /
• 1991

최근 압력용기, 고압배관, LNG Tank 및 선체등의 구조물 파괴에 대한 안전성을 보증하기 위하여, 구조부재의 표면결함에 대한 균열성장 거동을 파악하는 것이 중요한 과제중에 하나라고 인식되어지고 있다. 본 연구에서는 단일 및 복수표면 결함의 피로균열 성장을 바탕으로 표면에서 관통되기까지의 균열성장 수명의 추정등 실질적이고 일반적인 문제들을 해석할려고 시도하였다. 또한, 복수균열 문제에 적용하기 위하여 복수 언더컷의 합체진전현상을 검토하였으며 단일 언더컷과 복수 언더컷의 전파특성이 유사함을 밝혔다.

• Steel and Composite Structures
• /
• 제4권2호
• /
• pp.149-167
• /
• 2004

Offshore platforms have to serve in harsh environments and hence are likely to be damaged due to wave induced fatigue and environmental corrosion. Welded tubular joints in offshore platforms are most vulnerable to fatigue damage. Such damages endanger the integrity of the structure. Therefore it is all the more essential to assess the capacity of damaged structure from the point of view of its safety. Eight internally ring stiffened fatigue damaged tubular joints with nominal chord and brace diameter of 324 mm and 219 mm respectively and thickness 12 mm and 8 mm respectively were tested under axial brace compression loading to evaluate the reserve capacity of the joints. These joints had earlier been tested under fatigue loading under corrosive environments of synthetic sea water and hence they have been cracked. The extent of the damage varied from 35 to 50 per cent. One stiffened joint was also tested under axial brace tension loading. The residual strength of fatigue damaged stiffened joint tested under tension loading was observed to be less than one fourth of that tested under compression loading. It was observed in this experimental investigation that in the damaged condition, the joints possessed an in-built load-transfer mechanism. A bi-linear stress-strain model was developed in this investigation to predict the reserve capacity of the joint. This model considered the strain hardening effect. Close agreement was observed between the experimental and predicted results. The paper presents in detail the experimental investigation and the development of the analytical model to predict the reserve capacity of internally ring stiffened joints.

• Journal of Welding and Joining
• /
• 제23권5호
• /
• pp.61-68
• /
• 2005

Dissimilar joining of Al 6013-T4 alloys and austenite stainless steel was carried out using friction stir welding technique. Microstructures near the weld zone and mechanical properties of the joint have been investigated. Microstructures in the stainless steel side were composed of the heat affected zone and the plastically deformed zone, while those in the Al alloy side were composed of the recrystallized zone including stainless steel particles, the thermo-mechanically affected zone and the heat affected zone. TEM micrographs revealed that the interface region was composed of the mixed layers of elongated stainless steel and ultra-fine grained Al alloy with lamella structure and intermetallic compound layer. Thickness of the intermetallic layer was approximately 300nm and was identified as the A14Fe with hexagonal close packed structure. Mechanical properties, such as tensile and fatigue strengths were lower than those of 6013 Al alloy base metal, because tool inserting location was deviated to Al alloy from the butt line, which resulted in the lack of the stirring.