• 수산해양기술연구
• /
• 제27권3호
• /
• pp.193-210
• /
• 1991

For the deckhouse or superstructure, attention is directed to the reduction of vibration from a human susceptibility point of view. The two basic requirements for obtaining a low vibration level in the accommodation are to ensure that excitation forces from propeller and/or main engine are small and to avoid resonance excitation of the hull and superstructure. In recent years increased attention has been directed towards the problems of vibration and noise in deckhouse, which have caused major problems with regard to the environmental quality in the living quarters for crews. Accordingly, in this paper, the characteristic of the vibration of deckhouse of fishing boat, of which the length/height ratio is also relatively high, are studied systematically with regard to the shape and modelling of deckhouse based on finite element method of 1-dimensional, 2-dimensional and 3-dimensional model. This study is divided into 4-part. 1st part is the global deckhouse vibration, 2nd part is the local deckhouse vibration, 3rd part consists of the estimation for stiffness of foundational support and 4th part is the application to TUNA LONG LINER of 416 ton class. For the global vibration analysis, the severity of the vibration depends on the longitudinal shear and bending stiffness of the deckhouse, on the vertical deckhouse support(fore, aft and sides). However, even if the design is technically sound, vibration problems may arise due to vertical or longitudinal hull girder or afterbody resonances. Author applied the method of this study to the analysis of, deep-sea fishing vessel of G.T. 416 ton class with relatively low height and long deckhouse, and investigated the vibrational characteristic of the fishing vessel with earlier structural feature. According to this investigation, the vibration, response of above vessel was confirmed of which main hull and deckhouse behave as one body. It is at the bottom of vibrational trouble which a accommodation part of the fishing vessel is raised, that is the local vibration for side wall, fore-aft wall and deck plate of deckhouse rather than thief fect of fore-aft vibration of deckhouse for above fishing vessel. and the resonance of main hull, deckhouse and driving system such as the main engine, propeller in exciting source is mainly brought up as the trouble.

• 대한치과보철학회지
• /
• 제34권4호
• /
• pp.657-664
• /
• 1996

The purpose of this study was to compare the dimensional stability, compression resistance, elastic recovery and surface hardness of elastomeric interocclusal recording materials. Five commonly used elastomeric interocclusal recording materials(Ramitec, Regisil, Blue-Mousse, Stat-Br, Coltoflax) were selected for this study. According to ADA specification No. 19, two types of specimen were fabricated. Cylinder type specimens were used to test compression resistance and elastic recovery and plate type specimens were used to evaluate dimensional stability and surface hardness. Paired t-test was applied to detect significance among the occlusal registration materials. The obtained results were as follows: 1. There were statistical difference in dimensional stability between the elastic interocclusal recording materials. The dimensional stability of silicone was higher than that of polyether tested(p<0.05). 2. Coltoflax was significantly less resistance to compression than the other elastic interocclusal recording materials(p<0.001). 3. The elastic recovery capacity of Blu-Mousse and Stat-Br is better than that of Coltoflax (p<0.01). 4. The surface hardness of Coltoflax was lower than that of Blu-Mousse and Stat-Br(p<0.05). 5. The percentage dimensional change of alll materials was acceptable according to the limid of 0.5% suggeted by ADA specificatin No. 19.

• The Journal of Advanced Prosthodontics
• /
• 제12권4호
• /
• pp.233-238
• /
• 2020

PURPOSE. This study aims to compare the marginal fitness of two types of implant-supported fixed dental prosthesis, i.e., cementless fixation (CL.F) system and cement-retained type. MATERIALS AND METHODS. In each group, ten specimens were assessed. Each specimen comprised implant lab analog, titanium abutment fabricated with a 2-degree tapered axial wall, and zirconia crown. The crown of the CL.F system was retained by frictional force between abutment and relined composite resin. In the cement-retained type, zinc oxide eugenol cement was used to set crown and abutment. All specimens were sterilized with ethylene oxide, immersed in Prevotella intermedia culture in a 50 mL tube, and incubated with rotation. After 48 h, the specimens were washed thoroughly before separating the crown and abutment. The bacteria that penetrated into the crown-abutment interface were collected by washing with 500 µL of sterile saline. The bacterial cell number was quantified using the agar plate count technique. The BacTiter-Glo Microbial Cell Viability Assay Kit was used to measure bacterial adenosine triphosphate (ATP)-bioluminescence, which reflects the bacterial viability. The t-test was performed, and the significance level was set at 5%. RESULTS. The number of penetrating bacterial cells assessed by colony-forming units was approximately 33% lower in the CL.F system than in the cement-retained type (P<.05). ATP-bioluminescence was approximately 41% lower in the CL.F system than in the cement-retained type (P<.05). CONCLUSION. The CL.F system is more resistant to bacterial penetration into the abutment-crown interface than the cement-retained type, thereby indicating a precise marginal fit.

• 대한조선학회논문집
• /
• 제29권1호
• /
• pp.158-172
• /
• 1992

대형구조물의 국부구조계를 구성하는 후판, 선체이중저구조와 같은 복판팬널등의 진동문제에 있어서 전단변형 및 회전관성효과가 매우 크므로 정확한 진동해석을 위해서는 이들 구조계를 상기 효과를 고려한 Mindlin판유추 구조계로 취급하여야 한다. 또한, 이들 구조계의 실제 경계조건은 일반적으로 단순지지와 고정의 중간상태이므로 경계조건을 회전에 대한 탄성구속으로 다룰 필요가 있다. 그러나 4변모두 단순지지 경계조건을 갖는 Mindlin판을 제외하고는 엄밀해를 구하기 어려워 근사적 방법의 사용이 불가피한데, 한 방법으로 Rayleigh-Ritz 방법이 널리 이용된다. Rayleigh-Ritz 방법에 의한 Mindlin판유추 구조계의 진동해석에 있어서 진동파형가정함수로서 통상 Timoshenko보함수가 이용된다. 이 경우 전단변형의 효과가 고려되어야 하므로 횡방향처짐 및 굽힘회전각에 대한 2개의 함수계가 도입되어야 하므로 실제 연산이 Euler보함수를 이용한 박판유추 구조계의 진동해석 때 보다도 훨씬 더 복잡하다. 따라서, 본 논문에서는 이러한 연산의 복잡성을 줄이기 위해 진동파형가정함수로서 Timoshenko보함수 성질을 갖는 다항식 도출방안을 제시하였고, 이를 이용하여 주변경계조건이 회전에 대해 탄성구속된 Mindlin판유추 구조계의 진동해석 및 감도해석을 정식화하여, 등방성 후판 및 실선이중저구조의 1/8축척 모델을 대상으로 일련의 수치계산을 수행하여 이의 정확도 및 효율성을 검증하였다.

• 한국임상수의학회지
• /
• 제28권3호
• /
• pp.328-331
• /
• 2011

간헐적 전지 파행을 보이는 두 마리 개가 내원하였다. 신체 검사에서 약 $90^{\circ}$ 외측 회전을 동반한 전완 기형을 두 마리 모두에서 확인 하였다. 일반 방사선 사진에서 척골 원위부 아탈구, 요골 앞쪽 휨 현상, 짧아진 요골 척골, 및 앞발의 외측 회전을 확인하였다. 외측 회전을 동반한 전완 기형의 교정을 위해 척골 원위부 골절제와 요골 원위부 쐐기형 절골술 및 요골 원위부 내측 회전을 실시 하였다. 관절 부조화를 예방하기 위해 척골 근위부 절골술을 첫 번째 개에서 실시 하였다. 수술 후 정기 검진은 수의사의 신체 검사를 통해 실시 되었으며 두 마리 모두에서 수술과 관련한 합병 증상 및 파행이 없음을 확인하였다.

• Korean Journal of Acupuncture
• /
• 제35권1호
• /
• pp.41-45
• /
• 2018

Objectives : To investigate minimum pressure by verifying changes in pressure due to bleeding amount during bloodletting-cupping therapy. Methods : (1) We compared adhesion performance of four different cupping cups of same size: two disposable cupping cups(A, B) and two reusable cupping cups(A, B) each were vacuumed three times and kept in place for 10 minutes. (2) We vacuumed two different sized disposable cupping cups(A), size.1(InnerDiameter 48.8 mm) and size.3(InnerDiameter 39.1 mm), twice each(-200 mmHg) on silicon plate. We injected water and air at regular intervals in cupping cups by using a syringe, and then measured change of pressure in cupping cups and pressure at the time of dropout. Results : (1) Pressure reduction was $4.75{\pm}2.78%$ on average in the order of 'Disposable[A]>reusable[B]>Disposable[B]>reusable[A]', so that pressure retention performance of disposable cups can't be regarded as inferior to that of reusable cups. (2) Pressure of disposable cupping B(size.1) decreased by an average of -40.08 mmHg per 5 ml of water. At -24.8 mmHg, when 22 ml of water has been injected, cup has come off. Pressure of disposable cupping B(size. 3) decreased by an average of -99.4 mmHg per 5 ml of water. At -48.6 mmHg, when 13 ml of water was injected, cupping came off. Conclusions : Considering reduction rate of pressure due to water injection, in case of bleeding more than 15 ml, size.3 cup always comes off, therefore it needs to be re-operated at least once. Meanwhile, size.1 cup does not always come off in the same condition, depending on the initial pressure and therefore, re-operation may be considered.

• 대한소아치과학회지
• /
• 제23권2호
• /
• pp.489-501
• /
• 1996

This study was to evaluate shear bond strength of fluoride-releasing sealant and nonfluoride releasing sealant to enamel surface of bovine tooth. 80 extracted bovine teeth were randomly assigned to four groups, and four kinds of sealants including Teethmate-A(Kuraray Co.), Teethmate-F(Kuraray Co.), Helioseal(Vivadent Co.), Helioseal-F(Vivadent Co.) were bonded to exposed enamel surfaces using silicon plate. Shear bond strength was determined in an instron universal testing machine at a crosshead speed of 1mm/min. Then, the fracture surfaces of test specimens were investigated with scanning electron microscope. The obtained results were as follows; 1. The shear bond strength decreased in the following order : Teethmate-A(18.31MPa), Teethmate-F(11.90MPa), Helioseal (11.74 MPa), Helioseal-F(10.64MPa). 2. The shear bond strength of Teethmate-A showed significantly higher than that of Teethmate-F(P<0.05), but Helioseal and Helioseal-F didn't showed statistically different(P<0.05). 3. According to the SEM, Teethmate-A group showed cohesive failure, and Teethmate-A group & Helioseal group showed mixed pattern of cohesive and adhesive failure and Helioseal-F group showed adhesive failure.

• 대한화학회지
• /
• 제6권1호
• /
• pp.25-28
• /
• 1962

韓國産 水産통조림을 主로한 市中통조림의 各種 200 個를 random으로 取해 dithiol-比色法으로 內容物中의 주석含有量을 測定함으로써 그 實體를 調査하였다. 種類別에서 보면 오징어통조림이 가장 基해서 150ppm 以上이 되는 것이 약 50%나 되고, 다음의 고등어의 約 30%고, 꽁치가 約 20%였다. 이것에 比해 檢出品인 락카통의 게통조림과 조개, 고래통조림 等은 全部 完全하였고, 其他 소라, 魚類통조림도 150ppm 以上되는 것은 거의 없었다. pH값과의 關係는 같은 種類에 있어서는 어떤 範圍를 中心하여 그 값이 낮아지거나 혹은 높아지면 溶出量이 增加되는 傾向이 보인다. 이 外에 製造條件이 明確한 것에 對해서 보면, 通過料와는 거의 關聯性이 없고 貯藏其間은 길수록 溶出量이 많아 12個月以上에서는 150ppm를 넘는 것이 많았다. 溶解와 固形物에 있어서의 分布는 그 大部分이 液計에 分布되어 있다.

• Advanced Composite Materials
• /
• 제17권1호
• /
• pp.57-73
• /
• 2008

The present paper focuses on experimental verification of the ply-by-ply basis inelastic analysis of multidirectional laminates. First of all, rate dependence of the tensile behavior of balanced symmetric cross-ply T800H/epoxy laminates with a $[0/90]_{3S}$ lay-up under off-axis loading conditions at $100^{\circ}C$ is examined. Uniaxial tension tests are performed on plain coupon specimens with various fiber orientations $[{\theta}/(90-{\theta})]_{3S}$ ($\theta$ = 0, 5, 15, 45 and $90^{\circ}C$) at two different strain rates (1.0 and 0.01%/min). The off-axis stress.strain curves exhibit marked nonlinearity for all the off-axis fiber orientations except for the on-axis fiber orientations $\theta$ = 0 and $90^{\circ}$, regardless of the strain rates. Strain rate has significant influences not only on the off-axis flow stress in the regime of nonlinear response but also on the apparent off-axis elastic modulus in the regime of initial linear response. A macromechanical constitutive model based on a ply viscoplasticity model and the classical laminated plate theory is applied to predictions of the rate-dependent off-axis nonlinear behavior of the cross-ply CFRP laminate. The material constants involved by the ply viscoplasticity model are identified on the basis of the experimental results on the unidirectional laminate of the same carbon/epoxy system. It is demonstrated that good agreements between the predicted and observed results are obtained by taking account of the fiber rotation induced by deformation as well as the rate dependence of the initial Young's moduli.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.271-275
• /
• 2010

연소기 재생냉각 챔버 노즐확장부의 외피구조물 제작을 위한 성형치구 설계에 대한 연구를 수행하였다. 연소기 챔버에서 두께가 얇은 외피구조물은 판재의 성형을 이용하여 제작한다. 노즐확장부 외피구조물의 성형에서 노즐확장부와 동일한 형상의 치구로 성형하면 성형 후 구조물의 형상이 노즐확장부와 일치하지 않고 탄성복원에 의하여 그 형상이 변화한다. 따라서 노즐확장부 형상과 동일한 형상으로 성형을 완성하기 위해서는 탄성복원을 고려한 성형치구의 설계가 필요하다. 본 연구에서는 초기 성형 후 탄성복원에 의한 노즐형상과 실제 구조물의 형상과의 오차를 없애기 위하여 오차를 보상한 새로운 성형치구용 형상을 생성하였다. 구조해석 결과 설계 수정된 성형치구로 성형하면 노즐 형상과 성형된 구조물과의 형상 오차가 매우 작게 감소함을 확인할 수 있었다.