• 한국정밀공학회지
• /
• 제23권12호
• /
• pp.56-63
• /
• 2006

This paper describes the development of automatic making system of a frame element for flame prevention. The frame element is made by turning a thin plate and a formed plate on the small pipe. The couple plate(two plates) should be pulled with constant farce to manufacture a good frame element. This is because if the gap between one couple plate and other couple plate is different, it will not prevent flame. In this paper, the automatic making system of a frame element for flame prevention was made, and which could automatically manufacture a frame element. The characteristic test of the made frame element by that system was performed, and its result was very good.

• 설비공학논문집
• /
• 제18권4호
• /
• pp.359-369
• /
• 2006

This study aims deriving analysis the flow characteristic of kitchen hood system with using 3-D numerical analysis method and improving the system to expel pollutes more efficiently. This system is applied with $k-{\varepsilon}$ turbulent model and using incompressibility viscosity flow range and boundary condition which are related to Bossinesq approximation following density variation in control volume. To understand the flow characteristics of four models, this study only focuses on velocity field, temperature field, and concentration field varying with followings whether separation plate is set or not and the shapes of separation plates. The quantity of air, speed of exhaust fan and temperature and concentration of heating source are concerned as constant values.

• Structural Engineering and Mechanics
• /
• 제16권3호
• /
• pp.341-360
• /
• 2003

The goal of this paper is to determine the eigenvalues of a uniform rectangular plate carrying any number of spring-damper-mass systems using an analytical-and-numerical-combined method (ANCM). To this end, a technique was presented to replace each "spring-damper-mass" system by a massless equivalent "spring-damper" system with the specified effective spring constant and effective damping coefficient. Then, the mode superposition approach was used to transform the partial differential equation of motion into the matrix equation, and the eigenvalues of the complete system were determined from the associated characteristic equation. To verify the reliability of the presented theory, all numerical results obtained from the ANCM were compared with those obtained from the conventional finite element method (FEM) and good agreement was achieved. Since the order of the property matrices for the equation of motion obtained from the ANCM is much lower than that obtained from the FEM, the CPU time required by the ANCM is much less than that by the FEM.

• 전기의세계
• /
• 제25권6호
• /
• pp.81-88
• /
• 1976

The present voltage-reactive power control aims at an overall coordination of reactive power sources and voltage regulation devices to keep the bus voltages within their allowable bounds on one hand and to reduce the transmission losses on the other. This paper presents an efficient computer control scheme for the real-time control of system voltage and reactive power on the basis of a simplified linear equation by using the system characteristic constant. Computational algorithm is used for the minimization of bus voltage deviation in the first phase of optimization and for the reduction of transmission losses under the constraint of vlotage settling condition in the second phase. The numerical example for sample practical system is also given. The present study on the computer control scheme will contribute to the automation of power system operation in the near future.

• 한국항공운항학회지
• /
• 제14권4호
• /
• pp.17-23
• /
• 2006

This paper describes the preliminary design procedure for the hybrid propulsion system. For a given mission defined by velocity increment, the design of a polyethylene/LOX hybrid rocket was implemented. In addition, Seven-cluster multi-port fuel-grain was considered. After determining the system size including the combustion chamber, the performance parameters such as specific impulse, thrust, characteristic velocity, and thrust coefficient can be predicted by using empirical regression rate correlation, though most of preliminary design code assume constant regression rate. The results of the performance prediction indicated that besides the widely used HTPB/LOX, polyethylene/LOX hybrid motor can be a viable alternative to the more widely used SRMs.

• 산업기술연구
• /
• 제20권B호
• /
• pp.105-113
• /
• 2000

Air springs are now widely used in bus or truck suspensions due to their advantages over conventional metal spring as coil or leaf springs. Air springs have soft spring rates, which give better ride quality, and additional leveling system provides constant ride height and maintains almost same vertical natural frequencies. A mathematical model of an air spring suspension system with height control system is constructed and dynamic responses of the suspension system are investigated in the light of leveling valve motion characteristic, vertical motion natural frequency. Also, using a full vehicle model, handling characteristics of an air spring suspension is studied and the results are compared with real test results, which shows good agreements.

• 한국추진공학회지
• /
• 제21권1호
• /
• pp.36-43
• /
• 2017

본 연구에서는 케로신과 액체산소를 추진제로 사용하는 핀틀 인젝터의 설계/제작이 이루어졌으며, 연소실 특성길이와 운동량비에 따른 특성속도효율을 통해 연소성능을 확인하였다. 연소시험 결과, 핀틀 인젝터의 추진제 분무 특성으로 인한 재순환영역에 의해, 추진제 조합에 따른 특성길이 추천치보다 짧은 영역에서도 최적의 연소성능을 발휘하는 것을 확인하였다. 또한 운동량비가 연소성능에 지대한 영향을 미치나, 추천범위 1.0~1.5 내에서 특성속도효율이 일정하게 나타남을 확인하였다.

• 한국항공우주학회지
• /
• 제35권8호
• /
• pp.706-713
• /
• 2007

코안다 효과를 유발시키기 위해 환상 슬릿과 팽창률이 일정하지 않은 축소 노즐로부터 분사되는 제트의 구조와 환상의 슬릿과 팽창률이 일정한 노즐로부터 분사되는 제트의 구조를 비교 연구하였다. 실험에 있어서 노즐 입구와 출구 직경을 각각 40mm, 20mm로 하였고, 노즐 출구 평균 속도를 90m/s로 하였다. 3축 이송 장치와 스캐닝 밸브 시스템을 이용하여 제트 축 및 반경 방향 압력을 측정하고, 측정된 정압 및 전압으로부터 구한 속도 분포를 비교 검토하였다. 안정성과 수속성이 우수한 제트를 얻기 위해서는 팽창률이 일정하지 않은 노즐보다 팽창률이 일정한 축소 노즐과 환상의 슬릿을 통해 코안다 효과를 이용하여 분사하는 것이 효과적임을 밝혔다. 또한 팽창에 따른 압력 강하도 팽창률이 일정한 노즐의 경우가 상대적으로 더 작게 됨을 알았다.

• Wind and Structures
• /
• 제26권6호
• /
• pp.355-367
• /
• 2018

This paper studies the aerodynamic stability of a tensioned, geometrically nonlinear orthotropic membrane structure with hyperbolic paraboloid in sag direction. Considering flow separation, the wind field around membrane structure is simulated as the superposition of a uniform flow and a continuous vortex layer. By the potential flow theory in fluid mechanics and the thin airfoil theory in aerodynamics, aerodynamic pressure acting on membrane surface can be determined. And based on the large amplitude theory of membrane and D'Alembert's principle, interaction governing equations of wind-structure are established. Then, under the circumstance of single-mode response, the Bubnov-Galerkin approximate method is applied to transform the complicated interaction governing equations into a system of second-order nonlinear differential equation with constant coefficients. Through judging the frequency characteristic of the system characteristic equation, the critical velocity of divergence instability is determined. Different parameter analysis shows that the orthotropy, geometrical nonlinearity and scantling of structure is significant for preventing destructive aerodynamic instability in membrane structures. Compared to the model without considering flow separation, it's basically consistent about the divergence instability regularities in the flow separation model.

• 대한기계학회논문집A
• /
• 제26권10호
• /
• pp.2130-2141
• /
• 2002

A unique technique to estimate the magnitude or contribution ratio of each stage backlash in a system with a two-stage gear reducer is proposed. The concept to estimate the magnitude or contribution ratio of each stage backlash is based on the change of frequency response characteristic, in particular, the change of anti-resonant frequency and resonant frequency, due to the change of each stage backlash magnitude, even though the total backlash magnitude of a system with a two-stage gear reducer is constant. The validity of the technique is verified in a seeker gimbal and satisfactory results are obtained. It is thought that the diagnosis and maintenance of the manufacturing machines and systems with two-stage gear reducers will become more efficient and economical by virtue of the proposed technique.