• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10b
• /
• pp.1817-1822
• /
• 1991

A method of reducing overhead caused by the processor synchronization process and common memory accesses in finely grained tasks is described. We propose a scheduler which considers the preparation time during searching to minimize the redundant accesses to shared memory. Since the suggested hardware (synchronizer) determines the access order of processors and bus arbitration simultaneously by including the synchronization process into the bus arbitration process, the synchronization time vanishes. Therefore this synchronizer has no overhead caused by the processor synchronization[l]. The proposed scheduler algorithm is processed in parallel. The processes share the upper bound derived by each searching and the lower bound function is built considering the preparation time in order to eliminate as many searches as possible. An application of the proposed method to a multi-DSP system to calculate inverse dynamics for robot arms, showed that the sampling time can be twice shorter than that of the conventional one.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.11 no.3
• /
• pp.143-148
• /
• 2011

In this paper, a backstepping design is proposed to achieve stabilization and synchronization for the Lorenz-Stenflo (LS) chaotic system. The proposed method is a recursive Lyapunov-based scheme and provides a systematic procedure to design stabilizing controllers. The proposed controller enables stabilization of the chaotic motion and synchronization of two identical LS chaotic systems using only a single control input. Numerical simulations are presented to validate the proposed method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.2
• /
• pp.185-192
• /
• 2002

A novel GPS initial synchronization scheme with low hardware complexity is proposed. The proposed method has the decomposed differential matched filter, which consists of 25% multiplier and adder of the conventional matched filter. This paper presents the generalized mean acquisition time of initial synchronization scheme with multiple correlator. It is shown that the proposed method, in spite of its low hardware complexity, has the equal performance to the conventional method. The performance of the proposed method is verified through the simulation test by the GPS simulator. It is shown that the proposed method prevents the squaring loss of non-coherent integration.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.9
• /
• pp.1251-1260
• /
• 2002

Real-time application programs have synchronization constraints which need to be met between media-data. Synchronization method represents feedback method including virtual client-side buffer. This buffer is used in buffer level method. It is client-leading synchronization that is absorbing variable transmission delay time and that is synchronizing by feedback control. It is the important factor for playback rate and QoS if the buffer level is normal or not. To solve the problems, we can control the start of transmission in multimedia server by appling filtering, control and network evaluation function. Synchronization method is processing for smooth presentation without cut-off while media is playing out. When audio frame which is master media is in high threshold buffer level we decrease play out time gradually, otherwise we increase it slowly.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.9
• /
• pp.863-868
• /
• 2011

This paper presents a method to achieve a synchronous positioning objective for a dual-cylinder electro-hydraulic system with friction characteristics. The control system consists of a VSC (Variable Structure Controller) for each of the hydraulic cylinders and a PID (Proportional-Integral-Derivative) feedback controller. The PID controller is used for controlling the non-synchronous error generated by both cylinders when motion synchronization is carried out. To enhance the position-tracking performance of the individual cylinders friction characteristics is modeled in model, based on the estimated friction force. The simulation and experimental results show that the proposed method can effectively achieve the objective of position synchronization in the dualcylinder electro-hydraulic system, with maximum synchronization error with ${\pm}2\;mm$.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.441-450
• /
• 2008

The scalable extension of H.264, known as scalable video coding (SVC) has been the main focus of the Joint Video Team's work and was finalized at the end of 2007. Synchronization between media is an important aspect in the design of a scalable video streaming system. This paper proposes an efficient media synchronization mechanism for SVC video transport over IP networks. To support synchronization between video and audio bitstreams transported over IP networks, a real-time transport protocol/RTP control protocol (RTP/RTCP) suite is usually employed. To provide an efficient mechanism for media synchronization between SVC video and audio, we suggest an efficient RTP packetization mode for inter-layer synchronization within SVC video and propose a computationally efficient RTCP packet processing method for inter-media synchronization. By adopting the computationally simple RTCP packet processing, we do not need to process every RTCP sender report packet for inter-media synchronization. We demonstrate the effectiveness of the proposed mechanism by comparing its performance with that of the conventional method.

• Journal of information and communication convergence engineering
• /
• v.4 no.1
• /
• pp.28-35
• /
• 2006

In this paper, we propose to synchronization method for mutual cooperative control method that have unstable limit cycles in a chaos trajectory surface in the chaotic UAVs. We assume all obstacles in the chaos trajectory surface have a Van der Pol equation with an unstable limit cycle. We also show computer simulation results of Arnold equation, Chua's equation trajectories with one or more Van der Pol as a obstacles. We proposed and verified the results of the method to make the embedding chaotic UAV to synchronization with the chaotic trajectory in any plane.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.11 no.2
• /
• pp.77-83
• /
• 2011

In this paper, an active backstepping design is proposed to achieve control and synchronization of a new hyperchaotic system. The proposed method is a systematic design approach and exists in a recursive procedure that interlaces the choice of a Lyapunov function with the design of the active control. The proposed controller enables stabilization of chaotic motion to the origin as well as synchronization of the two identical new hyperchaotic systems. Numerical simulations illustrate the validity of the proposed control technique.

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2005.05a
• /
• pp.215-221
• /
• 2005

In this paper, we propose a method to a synchronization of chaotic UAVs that have unstable limit cycles in a chaos trajectory surface. We assume all obstacles in the chaos trajectory surface have a Van der Pol equation with an unstable limit cycle. The proposed methods are assumed that if one of two chaotic UAVs receives the synchronization command, the other UAV also follows the same trajectory during chaotic UAVs search on the arbitrary surface.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.6
• /
• pp.527-534
• /
• 2016

The non-rail mobile rack, which is used for cargo storage, can improve the storage capacities of logistics centers. Furthermore, it has the advantage that it can be used in traditional logistics centers without making any changes or renovation, such as installing rails. However, when the rack is operated by separated drive actuators mounted on the left and the right wheels, precise position control of the wheels is necessary even if the unbalanced cargo weight on the rack would affect the control. Therefore, internal synchronization control for position tracking between the left and right wheels on the non-rail mobile rack is necessary in this study. In addition, external synchronization control for realizing the same straight movements between mobile racks is necessary. For the internal and the external synchronization control, we propose a synchronization control algorithm based on the repetitive control theory. An internal synchronization control algorithm with repetitive control theory requires the application of the robust servo control method owing to parameter variations. In this case, we can set up the gains for the robust servo control system by considering the cargo variations on the mobile rack. Furthermore, for developing the external synchronization control algorithm, we use a double repetitive control system to perform synchronization control between mobile racks. The efficiency of the proposed control algorithm will be verified by simulation and experimental results. The proposed algorithm can be easily applied in the industry.