• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1120-1122
• /
• 2002

Switching power supply are widely used in many industrial field. Power factor improvement and harmonic reduction technique is very important in switching power supply. The power factor correction (PFC) circuit using boost converter used in input of power source is studied in this paper. It is analyzed distortional situations and harmonics of input currents that presented at continuous conduction mode(CCM) of boost PFC circuit. It is done simulations of harmonics distribution according to load variation by using PSPICE and MATLAB. From the actual experiment of boost PFC circuit the validity of the analysis is confirmed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.100-106
• /
• 2005

Generally, high frequency switching DC-DC converter that DC power supply for discharge lamp drive to generate ultraviolet rays(UV) is acted by hard switching mode is used. Therefore in this paper, wish to mix first existent first-side status phase shift PWM DC-DC converter and posing secondary-side status phase shift PWM DC-DC converter by high frequency link DC-DC converter that use soft switching circuit technology and develop DC power supply for discharge lamp drive. DC power supply driving Discharge lamp proposed describe validity through simulation and an experiment.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.186-192
• /
• 2002

In this paper, interleaved boost power factor corrector(IBPFC) is applied as a pre-regulator in switch mode power supply. IBPFC can reduce input current ripple and effectively increase the switching frequency without increasing the switching losses, because input current is divided each 50% by two switching devices. IBPFC can be classified as three cases by duty ratio condition in continuous current mode and be carried out state space average modeling. According to the modeling, steady and transient state analysis is performed by steady elements and perturbation element. Control transfer function is derived for design of control system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.137-142
• /
• 2023

When designing a SMPS(Switched Mode Power Supply) circuit, a part that is easily overlooked without special consideration is a snubber circuit. However, the performance degradation of the SMPS due to the snubber circuit and the effect on the entire SET cannot be ignored. In addition, a snubber circuit is added to both ends of the switch to protect the device from peak voltage and current during switching and to reduce loss during on/off switching. Therefore, in this paper, for a sufficient understanding of snubber circuits, theoretical analysis and experimental formulas that can be applied by designers during actual circuit design are arranged to promote optimization of snubber circuits.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.4B no.2
• /
• pp.65-72
• /
• 2004

Switching power supply systems are widely used in many industrial fields. Power factor correction (PFC) circuits have a tendency to be applied in new power supply designs. The input active power factor correction (APFC) circuits can be implemented in either the two-stage approach or the single-stage approach. The two-stage approach can be classified into boost type PFC circuit and dc/dc converter. The power factor correction circuit with a boost converter used as an input power source is studied in this paper. In a boost power factor correction circuit there are two feedback control loops, which are a current feedback loop and a voltage feedback loop. In this paper, the regulation performance of output voltage and compensator to improve the transient response presented at the continuous conduction mode (CCM) of the boost PFC circuit is analyzed. The validity of designed boost PFC circuit is confirmed by MATLAB simulation and experimental results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.4
• /
• pp.307-313
• /
• 2019

The traveling wave tube amplifier (TWTA), which can be applied to the Ka-band millimeter-wave multi-mode seeker, consists of an high voltage power supply(HVPS), a grid modulator, a command and control, and an RF assembly. We designed a power supply that generates a -17.9 kV high voltage by synchronizing the pulse repetition frequency(PRF) and power supply switching frequency(i.e. synchronization frequency), and a high-speed grid-switching modulator for RF pulse modulation. The TWTA, which is fabricated through miniaturization with a volume of 3.18 L, has high pulse switching characteristics of up to 18.5 ns. The maximum rise/fall time of the grid on/bias signal and peak power is more than 564.9 W. Moreover, an excellent spurious performance of -68.4 dBc or less was confirmed within the range of PRF and PRF/2.

• Journal of information and communication convergence engineering
• /
• v.9 no.1
• /
• pp.74-77
• /
• 2011

PSPICE modeling of a commercial LED driver IC (TOP245P) and PC817A optocoupler is proposed for the switch-mode power supply (SMPS) (applicable to LED driver) design and simulation. An analog behavioral model of the TOP245P IC including the shunt regulator, under-voltage(UV) detection, over-voltage(OV) shut-down and SR flip-flop is developed by using PSPICE. The empirical equation of PC817A current transfer ratio (CTR) is fitted from the datasheet of PC817A. Two types of SMPSs are simulated with the averaged-model and switching-model. The simulation results by the proposed PSPICE models are in good agreement with those in the data sheet and an experimental data.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.137-139
• /
• 2005

본 논문에서는 30W급 스위칭형 직류전원장치 (Switching Mode Power Supply : SMPS)에 준공진형 프라이 백 스위칭 레귤레이터(quasi-resonant flyback switching regulator)를 적용하여 방사노이즈(radiation-noise)를 억제한 사례에 대하여 설명하고 있다. 기존의 PI사(社)의 TOP IC 시리즈$^{[1]}$와 같이 보편적으로 사용되고 있는 일명, 하드 스위칭(hard-switching)형 레귤레이터를 사용할 경우, 고속 스위칭시에 스위칭 손실(switching loss)과 스위칭 노이즈(switching noise)가 발생한다. 이로 인하여 SMPS의 발열에 따른 효율저화와 방사 노이즈에 의한 전파방해 등이 문제점이 된다. 본 논문에서는 일본의 Sanken사(社)에서 개발/시판중인 준공진형 스위칭 레귤레이터인 STR-F6000 IC 시리즈$^{[2]}$를 이용하여 프라이백 SMPS를 구성하여 방사노이즈를 저감하였다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.8
• /
• pp.392-401
• /
• 2001

This paper presents the single-stage high power factor AC to DC converter operated in active-clamp mode. The proposed converter is added active-clamping circuit to boost-flyback single-stage power factor corrected power supply. The active-clamping circuit limits voltage spikes, recycles the energy trapped in the leakage inductance, and provides a mechanism for achieving soft switching of the electronic switches to reduce the switching loss. The auxiliary switch of active-clamping circuit uses the same control and driver circuit as the main switch to reduce the additional cost and size. To verify the performance of the proposed converter, a 100W converter has been designed. The proposed converter gives good power factor correction, low line current harmonic distortions, and tight output voltage regulation, as used unity power factor.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.125-127
• /
• 1998

The widely used power supply (Switched Mode Power Supply : SMPS) as a source in order to stabilize direct current for electronics or communication systems has merits, when it is compared to the existing source for stability, such as high efficiency, small size, light weight by means of switching process of the semiconductor device which controls the flow of power. However, due to existence of inductors and capacitors used for charging energy, the source part in electronic or communication systems hasn't reached the speed, that is supposed to get, for achieving smaller size and lighter weight. In order to got smallness in size, it is necessary to increase switching frequency. And that makes devices for measuring energy smaller. Nevertheless, the rise switching frequency brings increases in switching loss, inductor loss, and power loss. Also, the occurrence of surge and noise caused by high frequency switching is setting higher. The resonant converter has been considered as one of methods that give solutions for the problems of SMPS and that method has been paid attention as a source technology in electronics and communication.