• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Korean Journal of Acupuncture
• /
• v.22 no.1
• /
• pp.95-108
• /
• 2005

Objective : In the present study, the effect of electroacupuncture (EA) applied to several acupoints and non-acupoint in CFA-induced knee arthritis was examined. Methods : A common source of persistent pain in humans is arthritis. Arthritis was induced by injection of CFA $125\;{\mu}l$ into knee joint cavity under enflurane anesthesia. The rat subsequently showed swelling of the ankle and a reduced stepping force of the affected limb for the next several days. The reduced stepping force of the limb was presumably due to a painful knee. EA was applied to either of $LR_2,\;LI_4$, or non-acupoint on the contralateral forelimb for 30 min under gaseous anesthesia. After the termination of EA, behavioral tests measuring stepping force were periodically conducted during the next 4 h. Results : EA applied to $LR_2$ point produced a significant improvement of stepping force of the affected foot lasting for at least 2 h. However, neigher $LI_4$ point nor non-point produced any significant increase of weight bearing force. The improvement of stepping pressure was interpreted as an analgesic effect. The analgesic effect was specific to the acupuncture point since the analgesic effect on CFA-induced knee arthritic pain model could not be mimicked by EA applied to a point, $LI_4$ or non-acupoint. In addition, both NO production and iNOS protein expression increased by arthritis were suppressed by EA applied to $LR_2$ point. Conclusion : These data suggest that EA produces a potent analgesic effect in the rat model of CFA-induced knee arthritis. This analgesic effect is produced by applying EA to an acupoint at opposite side from the painful area in a stimulus point-specific way.

• Childhood Kidney Diseases
• /
• v.23 no.1
• /
• pp.53-57
• /
• 2019

Renal cortical necrosis (RCN) is patchy or diffuse ischemic destruction of the renal cortex caused by significantly reduced renal arterial perfusion. It is a rare cause of acute kidney injury (AKI) and is associated with high mortality. Here, we review the case of RCN in a 15-year-old boy who developed AKI. A 15-year-old boy was referred to our hospital from a local hospital due to a sharp decrease in his renal function. He presented with acute flank pain, nausea with vomiting, and oliguria for the past two days. He had taken a single dose of antihistamine for nasal congestion. At our hospital, his peak blood pressure was 148/83 mmHg and he had a high body mass index of $32.9kg/m^2$. The laboratory data showed a blood urea nitrogen (BUN) of 28.4 mg/dL, a creatinine of 4.26 mg/dL, and a glomerular filtration rate estimated from the serum cystatin C of $20.2mL/min/1.73m^2$. Proteinuria (spot urine protein to creatinine ratio 1.66) with pyuria was observed. Kidney sonography showed parenchymal swelling and increased renal echogenicity. Due to rapidly progressing nephritis, steroid pulse therapy (750 mg/IV) was done on the second day of his admission and the patient showed complete recovery with normal renal function. However, the kidney biopsy findings revealed renal cortical hemorrhagic necrosis. Multifocal, relatively well-circumscribed, hemorrhagic necrotic areas (about 25%) were detected in the tubulointerstitium. Although RCN is an unusual cause of AKI, especially in children, pediatricians should consider the possibility of RCN when evaluating patients with rapidly decreasing renal function.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.1-13
• /
• 2023

Sengon (Falcataria moluccana Miq.) tree offers a wood of low quality and durability owing to its low density and thin cell walls. This study aimed to improve the properties of sengon wood by making the wood magnetic, producing new functions, and characterizing magnetic sengon wood. Each wood sample was treated using one of the following impregnation solutions: Untreated, 7.5% nano magnetite-furfuryl alcohol (Fe₃O₄-FA), 10% nano Fe₃O₄-FA, and 12.5% nano Fe₃O₄-FA. The impregnation process began with vacuum treatment at 0.5 bar for 2 h, followed by applying a pressure of 1 bar for 2 h. The samples were then tested for dimensional stability and density and characterized using scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDX), Fourier transform infrared spectrometry (FTIR), X-ray diffraction (XRD) analysis, and vibrating sample magnetometry (VSM) analysis. The results showed that the Fe₃O₄-FA impregnation treatment considerable affected the dimensional stability, measured in terms of weight percent gain, anti-swelling efficiency, water uptake, and bulking effect, as well as the density of sengon wood. Changes in wood morphology were detected by the presence of Fe deposits in the cell walls and cell cavities of the wood using SEM-EDX analysis. XRD and FTIR analyses showed the appearance of magnetite peaks in the diffractogram and Fe-O functional groups. Based on the VSM analysis, treated sengon wood is classified as a superparamagnetic material with soft magnetic properties. Overall, 10% Fe₃O₄-FA treatment led to the highest increase in dimensional stability and density of sengon wood.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.56-63
• /
• 1996

This study was to manufacture thinned wood of Larix leptolepis Gordon into Oriented Strand Board(OSB) with Urea-Formaldehyde Resin. The OSB was made of four kinds of strand in slenderness ratio 150 ; thickness $0.3{\pm}0.05mm$, $0.4{\pm}0.05mm$, $0.5{\pm}0.05mm$ and $0.6{\pm}0.05mm$, respectively length 45mm, 60mm, 75mm and 90mm. Target densities were 0.65gr/$cm^3$, 0.75gr/$cm^3$ and 0.85gr/$cm^3$. The stepwise 9 minutes-multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 10kgf/$cm^2$ was applied for $400mm{\times}390mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. In MOR The OSB of thin strand thickness $0.3{\pm}0.05mm$(length 45mm) and density 0.85gr/$cm^3$ was the highest. The strand thickness had more effect on MOR than the strand length. In strand thickness $0.4{\pm}0.05mm$(length 60mm) and density 0.85gr/$cm^3$ was the highest MOE. The strand thickness and length had adverse effects on MOE each other. At internal bonding. The OSB of strand thickness $0.3{\pm}0.05mm$(length 45mm) and board density 0.75gr/$cm^3$ showed the highest value. OSB had higher IB value with thinner strand thickness. The thinner strand thickness showed the lower thickness swelling in turn $0.3{\pm}0.05mm$(length 45mm), $0.4{\pm}0.05mm$(length 60mm), $0.5{\pm}0.05mm$(length 75mm). $0.6{\pm}0.05mm$(length 90mm). Target densities 0.75gr/$cm^3$ 0.65gr/$cm^3$, 0.85gr/$cm^3$ showed in turn lower value. Finally, The OSB made of thinned wood of Larix leptolepis Gordon showed good results in laboratory experiment.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.248-248
• /
• 2017

This study was carried out to compare the cooking and antioxidant characteristics of cooked rice added at various rate of glutinous rice addition and treated with two cooking methods. Cooked rice added with glutinous rice was cooked by general and high pressure cooking method with and without fermented alcohol. Pasting characteristics of cooked rice were decreased as increasing the amounts of glutinous rice. Water binding capacity and swelling power were significant decreased with the amounts of glutinous rice increasing, however water solubility indices were significant increased. Palatability characteristics of cooked rice added with glutinous rice showed similar results to cooked rice without glutinous rice. Total polyphenol contents of cooked rice added with glutinous rice and fermented alcohol were significantly distinct, but there was no significant difference. Total flavonoid contents were increased as increasing the amounts of glutinous rice. Total flavonoid contents by general cooking method of cooked rice added with 20% glutinous rice and fermented alcohol were $23.20{\pm}0.61{\mu}g\;CE/g$. DPPH radical scavenging activities added with and without glutinous rice were 2.97~5.19 and 3.19~5.45 mg TE/100 g, respectively. ABTS radical scavenging activities by high pressure cooking method of cooked rice added with 20% glutinous rice and fermented alcohol were $19.48{\pm}0.63mg\;TE/100g$. In this study, cooking and antioxidant characteristics of cooked rice added with glutinous rice were expected to be used as basic data on manufacturing processed products.

• Tunnel and Underground Space
• /
• v.30 no.5
• /
• pp.446-461
• /
• 2020

Numerical simulations of CIEMAT column test in Spain are performed to investigate the coupled thermo-hydro-mechanical (THM) behavior of MX80 bentonite pellets using TOUGH2-FLAC3D. The heater power and injection pressure of water in the numerical simulations are identical to those in the laboratory test. To investigate the applicability of the thermo-hydraulic (TH) model used in TOUGH2 code to prediction of the coupled TH behavior, the simulation results are compared with the observations of temperature and relative humidity with time. The tendencies of the coupled behavior observed in the test are well represented by the numerical models and the simulator in terms of temperature and relative humidity evolutions. Moreover, the performance of the models for the reproduction and prediction of the coupled TH behavior is globally satisfactory compared with the observations. However, the calculated stress change is relatively small and slow due to the limitations of the simple elastic and swelling pressure model used in numerical simulations. It seems that the two models are insufficient to realistically reproduce the complex coupled THM behavior in the bentonite pellets.

• The Korean Journal of Pharmacology
• /
• v.2 no.1 s.2
• /
• pp.49-69
• /
• 1966

For the purpose of stydying the pharmacodynamic action of methemoglobin, the author made the following experiments: 1. Preparation of hemoglobin and methemoglobin solutions: Red cell suspension from rabbit blood was hemolysed with distilled water and then divided into two portions. One portion was dialysed through cellophane paper and made isotonic with the proper amount of sodium chloride. The second portion was treated with sodium nitrite to convert hemoglobin to methemoglobin, dialysed through cellophane paper and made isotonic. 2. The concentration of methemoglobin in solution, plasma and urine was determined by Horecker and Brackette's method, and that of hemoglobin by the cyanmethemoglobin method. 3. The concentration of methemoglobin and hemoglobin in the plasma and urine of rabbits was measured at several intervals of time after infusion of the above samples. 4. The blood pressure and respiration of rabbits were recorded on a kymograph, and the effects of the samples on them were observed. 5. The effects of the samples on the movements of the in-situ heart and the isolated intestine of rabbits were studied. 6. The kidneys of rabbits were excised 4 to 5 hours after injection of the samples, and histopathological examinations were made. These experiments revealed the following results: 1. When methemoglobin solution was allowed to stand in room air, there was no decrease in the concentration of methemoglobin. 2. When methemoglobin solution was mixed with whole blood and incubated at $37^{\circ}C$, the concentration of methemoglobin decteased gradually. 3. After the infusion of methemoglobin and hemoglobin solutions, the rate of disappearance of methemoglobin in the plasma was more rapid than that of hemoglobin in the plasma. The higher the initial concentration in the plasma, the larger was the rate of disappearance of methemoglobin. 4. The rate of disappearance of methemoglobin was exceedingly rapid for 30 minutes after the infusion. 5. The urinary excretion of methemoglobin was more rapid than that of hemoglobin. 6. It would seem that the circulating blood contains substances which are promptly mobilized in the plasma to reduce methemoglobin to hemoglobin. 7. Moderate amounts of methemoglobin solution caused some rise in the blood pressure and a transient acceleration of the respiration of the rabbits. These effects of methemoglobin were milder than those of hemoglobin. 8. The movements of the in-situ heart and the isolated intestine of rabbits were accelerated by methemoglobin. These accelerating effects were milder than those of hemoglobin. 9. In the kidneys of rabbits treated with methemoglobin solution, hyperemia of the glomeruli, cloudy swelling and hemoglobin deposit in the tubular epithelium, hemoglobin casts in the tubular lumina of the proximal tubules, and interstitial congestion were constantly observed. There was no definite difference between the histological findings in the rabbit kidneys injected with methemoglobin, and those injected with hemoglobin solutions.

• Food Science of Animal Resources
• /
• v.33 no.2
• /
• pp.162-169
• /
• 2013

We determined the optimum pretreatment conditions such as pH and time for swelling duck feet and investigated the effects of the extracting method, such as water bath (WB), pressure cooker (PC), and microwave oven (MO), on quality characteristics of the duck feet gelatin for improving utilization of duck feet as a novel source of gelatin. The soaking solution of pH 1 among pH 1-14 with unit intervals was selected due to the highest yield. The quality characteristics of the gelatin tested were color, pH, gel strength, viscosity, and melting point. For the extracted gelatin with different methods, the CIE $L^*$, $a^*$ and $b^*$ values were in the following order: MO>PC>WB (p<0.05), WB>PC>MO (p<0.05) and PC>MO>WB (p<0.05), respectively. The gelatin extracted using WB showed the highest pH and that extracted using MO showed the lowest pH (p<0.05). The gel strength, viscosity, and melting point were the highest for MO (p<0.05). The gel strength and melting point were the lowest for PC (p<0.05). No significant difference was found in viscosity between the gelatins extracted using WB and PC (p>0.05). The quality characteristic of duck feet gelatin was affected by extracting methods, and MO extraction can be one of the effective methods for duck feet gelatin.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.12
• /
• pp.57-62
• /
• 2010

In this study, the effect of different silt contents on the shear characteristics of silty sands was evaluated. Two series of triaxial compression tests were performed on the cylindrical specimens of compacted Nakdong river sand with 10% and 30% silt contents under unconsolidated undrained condition. All identical specimens were prepared to compact with same initial water content for five layers and saturated using control panel and then sheared under initial effective confining pressure, 100 to 400kPa. All specimens exhibited a strain softening tendency after failure in stress-strain curves and deviator stresses of specimens with 10% silt content were greater than those of specimens with 30% silt content. Pore water pressures of specimens with 10% silt content were observed negative(i.e. swelling) due to increasing void ratio after failure but those of specimens with 30% silt content were shown only positive. The behavior of compacted cylindrical specimens with low silt content was more dilative than that of high silt content. Peak deviator stresses decreased as increasing silt content and peak pore water pressures increased as increasing silt content.