• 한국분무공학회지
• /
• 제17권3호
• /
• pp.121-127
• /
• 2012

The study is to investigate the mixing stability, fuel properties, and macroscopic spray characteristics of diesel-gasoline blended fuels in a common-rail injection system of a diesel engine. The test fuels were mixed diesel with gasoline fuel, which were based volume fraction of gasoline from 0 to 100% in 20% intervals. In order to analyze the blended effect of gasoline to diesel fuel, the properties of test fuels such as density, viscosity, and surface tension were measured. In addition, the spray behavior characteristics were studied by investigating the spray tip penetration and spray angle using a spray images through a spray visualization system. It was revealed that the density, kinematic viscosity and surface tension of diesel-gasoline blending fuels were decreased with the increase of gasoline fuel. The injection quantity of test fuels were almost similar level at short energizing duration condition. On the other hand, the increase of energizing duration shows the decrease of injection quantity compared to short energizing duration. The test blending fuels have similar growth in Spray tip penetration and Spray cone angle.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2003년도 The Fifth Asian Computational Fluid Dynamics Conference
• /
• pp.162-163
• /
• 2003

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.191-195
• /
• 2009

A parametric study for for the water entry of a two dimensional symmetric wedge with deadrise angle of 10 degrees was carried out to find out the most dominant parameter. Water entry problem with constant velocity is simplified as the stationary wedge in the way of the upcoming water surface. The calculated impact loads showed that the effect of the viscosity was not so important in this problem. For a given grid system a suitable time step size can be found. The most sensitive parameter was found to be the grid size.

• Journal of Pharmaceutical Investigation
• /
• 제13권3호
• /
• pp.89-99
• /
• 1983

Nylon microcapsules containing acetaminophen could be obtained by interfacial polymerization between sebacoyl chloride and 1, 6-hexamethylenediamine. Methylcellulose affected the micromeritic properties and dissolution characteristics of microcapsules. The particle size distribution was affected by the stirring speed and viscosity grade of methylcellulose. The surface observed by the scanning electron microscopy was affected by the methylcellulose. Nylon microcapsules produced in above method containing acetaminophen exhibited the retarded dissolution in comparison with uncoated acetaminophen. Release of acetaminophen from microcapsules decreased with decreasing pH of medium and with increasing the viscosity grade of methylcellulose and stirring speed.

• Korea-Australia Rheology Journal
• /
• 제12권2호
• /
• pp.107-117
• /
• 2000

Prediction of the product shape in sheet casting process is performed from the numerical simulation. A three-dimensional finite element method is used to investigate the flow behavior and to examine the effects of processing conditions on the sheet produced. Effects of inertia, gravity, surface tension and non-Newtonian viscosity on the thickness profile of the sheet are considered since the edge bead and the flow patterns in the chill roll region have great influence on the quality of the products. In the numerical simulation with free surface flows, the spine method is adopted to update the free surface, and the force-free boundary condition is imposed along the take-up plane to avoid severe singularity problems existing at the take-up plane. From the numerical results of steady isothermal flows of a generalized Newtonian fluid, it is shown that the draw ratio plays a major role in predicting the shape of the final sheet produced and the surface tension has considerable effect on the bead thickness ratio and the bead width fraction, while shear-thinning and/or tension-thickening viscosity affect the degree of neck-in.

• Journal of the Korean Wood Science and Technology
• /
• 제22권1호
• /
• pp.85-90
• /
• 1994

The flow properties of binder latices for paper coating were investigated, together with dynamic viscoelastic properties of latex films and electron micrographs of latices, under various conditions. The amphoteric latex, binder pigment latex and anionic latex were used in this work. The amphoteric latex has both anionic and cationic functional group on its surface. The binder-pigment with a core-shell structure has dual functions : plastic pigment and binder. The low shear viscosity of binder latices and clay slurry were measured with Brookfield vis cometer. At low-shear rates. the viscosity decreased with increasing particle size of latex. On the amphoteric latex surface, the carboxyl groups are assumed to be fully dissociated over the region of pH 9~12, but the density of negative groups seems to be increased because of the gradual decrease in the degree of dissociation of amino groups. Since the apparent particle size of latex increases with surface charge, the electroviscous effect can be observed. On the anionic latex surface, the charge density is assumed to be nearly constant above pH 8. However, below pH 8 the coagulation of particles could be observed probably because of the decrease in the charge density.

• 펄프종이기술
• /
• 제46권6호
• /
• pp.50-55
• /
• 2014

An oxidized starch was modified for surface sizing via etherification and esterification. Propylene oxide (PO), sodium monochloroacetate (SMCA), and acrylonitrile (AN) were used as etherification, and vinyl acetate monomer (VAM), maleic anhydride (MA), fumaric acid (FA), and itaconic acid (ITA) were used for esterification. Esterification and etherification of starch decreased both Brookfield viscosity and Brabender viscosity substantially even though the solids level was increased by 2% from 14 to 16%. Surface sizing performance of starches in tensile strength, stiffness and compressive strength was improved by esterification and etherification of the oxidized starch. Especially, SMCA etherification was found to be the most effective modification method.

• 접착 및 계면
• /
• 제5권2호
• /
• pp.31-42
• /
• 2004

Many animals possess on their legs adhesive pads, which have undergone evolutionary optimization to be able to attach to variable substrates and to control adhesive forces during locomotion. Insect adhesive pads are either relatively smooth or densely covered with specialized adhesive hairs. Theoretical models predict that adhesion can be increased by splitting the contact zone into many microscopic, elastic subunits, which provides a functional explanation for the widespread 'hairy' design. In many hairy and all smooth attachment systems, the adhesive contact is mediated by a thin film of liquid secretion between the cuticle and the substrate. By using interference reflection microscopy (IRM), the thickness and viscosity of the secretion film was estimated in Weaver ants (Oecophylla smaragdina). 'Footprint' droplets deposited on glass are hydrophobic and form low contact angles. IRM of insect pads in contact showed that the adhesive liquid is an emulsion consisting of hydrophilic, volatile droplets dispersed in a persistent, hydrophobic phase. I tested predictions derived from film thickness and viscosity by measuring friction forces of Weaver ants on a smooth substrate. The measured friction forces were much greater than expected assuming a homogenous film between the pad and the surface. The findings indicate that the rubbery pad cuticle directly interacts with the substrate. To achieve intimate contact between the cuticle and the surface, secretion must drain away, which may be facilitated by microfolds on the surface of smooth insect pads. I propose a combined wet adhesion/rubber friction model of insect surface attachment that explains both the presence of a significant static friction component and the velocity-dependence of sliding friction.

• 대한기계학회논문집A
• /
• 제37권5호
• /
• pp.625-630
• /
• 2013

본 연구는 직경 45 nm인 원통형 나노동공을 가진 산화알루미늄(AAO) 박막에 오일을 함침시켰을때 동점도가 마찰 마멸에 미치는 영향을 규명하고자 실시하였다. 양극산화법으로 제조한 AAO 박막을 직경 1 mm의 440C 스테인리스 강구를 상대재로 하여 왕복동 미끄럼 접촉시험을 실시하였다. 마찰면과 마멸입자는 주사전자현미경과 에닥스(Energy-dispersive X-ray)를 이용해 분석하였다. 높은 동점도 오일의 윤활효과가 저점도 오일에 비해 크게 향상되었다. 동점도가 낮은 경우엔 모든 하중조건에서 심한 마찰흔적과 함께 두꺼운 소성변형층이 넓게 형성되었으며 경계윤활막의 손상으로 접촉면에 물질전이와 화학적 반응 현상이 모두 발생하였다. 오일의 점도가 높은 경우 마찰면에 존재하는 경계윤활막이 파괴되지 않아 마찰흔적과 소성변형층의 형성이 매우 적었으며 물질전이와 화학적 반응이 방지되었다.

• Korean Chemical Engineering Research
• /
• 제55권5호
• /
• pp.690-697
• /
• 2017

본 연구에서는 방수시트재를 위한 아스팔트의 styrene-butadiene-styrene (SBS)와 styrene-isoprene-styrene (SIS)에 의한 개질에 있어서 자가치유성을 가지는 개질아스팔트 방수시트재의 연화점(softening point), 침입도(penetration), 저온굴곡저항성능(low temperature flexibility), 점도(viscosity) 및 부착성능(adhesion) 등의 물성을 관찰하고, 반응표면분석법(response surface methodology, RSM)을 활용하여 아스팔트 질량 대비 SBS와 SIS의 적정조성을 도출하고 자가치유성을 가지는 개질아스팔트 방수시트재의 물성을 최적화하였다. 고온에서 측정이 수행되는 연화점과 점도는 SBS 또는 SIS의 함량이 증가함에 따라서 유의하게 값이 증가하였다. 그러나 함량 대비 연화점과 점도 증가분은 SBS 경우가 SIS보다 커짐이 관찰되었다. 이러한 원인은 SBS와 SIS의 열적거동의 차이 때문인데, SBS는 고온에서 점도 상승을 동반하는 겔화(gelation)가 되어 가교도가 커지나 SIS는 점도감소를 초래하는 폴리이소프렌 블록의 사슬분리(chain scission) 때문에 사슬꼬임(chain entanglement)이 상대적으로 적어지기 때문이다. 반면에 SIS-SBS 개질아스팔트는 상온에서 측정되는 침입도, 부착성능 및 저온굴곡성능에 대하여, 아스팔트 63 g을 기본으로 SIS 4~5 g과 SBS 8.5 g의 조성에서 최소 탄성거동을 나타내어 최대 침입도 및 최대 부착성능과 최저 저온굴곡성능 값을 보였다.