• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.457-464
• /
• 2000

Stereographic method is a general and basic method to analyse sliding failure potential of rock slope. Region of failure analysis using stereographic method extend to curved slope from straight slope in this paper, Curved slope is defined as the multi-face slope with free surface more than two face and has different characteristics from straight single face slope. Individual daylight envelopes of free surfaces are combined into total daylight envelope of multi-face slope. So, sliding envelope of multi-face slope is the daylight envelope except friction cone. Specially, If only single joint set is developed in the slope, single plane sliding(or plane failure) is impossible in the single-face straight slope, but possible in the multi-face slope. In the multi-face slope with only one joint set, single plane sliding occurs when orientation of sliding plane is between two side slope orientation in the sliding envelope.

• Geomechanics and Engineering
• /
• v.6 no.6
• /
• pp.561-575
• /
• 2014

Estimating seismic displacements has a great importance for foundations on or adjacent to slope surfaces. However, dynamic solution of the problem has received little attention by previous researchers. This paper presents a new analytical model to determine seismic displacements of the shallow foundations adjacent to slopes. For this purpose, a dynamic equilibrium equation is written for the foundation with failure wedge. Stiffness and damping at the sliding surface are considered variable and a simple method is proposed for its estimation. Finally, for different failure surfaces, the calculated dynamic displacement and the surfaces with maximum strain are selected as the critical failure surface. Analysis results are presented as curves for different slope angles and different foundation distances from edge of the slope and are then compared with the experimental studies and software results. The comparison shows that the proposed model is capable of estimating seismic displacement of the shallow foundations adjacent to slopes. Also, the results demonstrate that, with increased slope angle and decreased foundation distances from the slope edge, seismic displacement increases in a non-linear trend. With increasing the slope angle and failure wedge angle, maximum strain of failure wedge increases. In addition, effect of slope on foundation settlement could be neglected for the foundation distances over 3B to 5B.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.09b
• /
• pp.842-845
• /
• 2005

A method for the numerical simulation of two-dimensional free-surface flow resulting from the propagation of regular gravity waves over topography with arbitrary bottom shape is presented. The method is based on the numerical solution of the Euler equations subject to the fully nonlinear free-surface boundary conditions and the appropriate bottom, inflow and outflow conditions using a hybrid finite-differences and spectral-method scheme. The formulation includes a boundary-fitted transformation, and is suitable for extension to incorporate large-eddy simulation (LES) and large-wave simulation (LWS) terms for turbulence and breaking wave modeling, respectively. Results are presented for the simulation of the free-surface flow over two different bottom topographies, with constant slope values of 1:10 and 1:20, two different inflow wave lengths and two different inflow wave heights. An absorption outflow zone is utilized and the results indicate minimum wave reflection from the outflow boundary. Over the bottom slope, lengths of waves in the linear regime are modified according to linear theory dispersion, while wave heights remain more or less unchanged. For waves in the nonlinear regime, wave lengths are becoming shorter, while the free surface elevation deviates from its initial sinusoidal shape.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.736-744
• /
• 2009

The abrupt failure of slope caused by a concentrated rainfall would be a disaster in this country. Specially, the soil slope may be collapsed by the rainfall seepage, however, there is not much information for the mechanism of slope failure during rainfall. As analyzing the stability of slope by rainfall, the conventional method is to put the ground-water level on the surface of slope. However, it may provide the over-reinforcement for the slope stability. Futhermore, although over-reinforcement for the slope was fulfilled, the possibility of potential slope failure still exists. In this study, the slope stability by the conventional design method and the causes of unstable slope during rainfall were investigated. To analyze the slope stability by rainfall, the computer program SEEP/W for the analysis of seepage was used. As changing the intensity and duration of rainfall in SEEP/W, the analysis were performed. After completion of analysis, the porewater pressure data from SEEP/W was applied to SLOPE/W. As a results of this analysis, it is not reasonable that the groundwater level is going up to the surface of slope during rainfall. Therefore, the conventional reinforcement for the slope stability is not obvious to satisfy the criterion safety factor during rainfall. The reasonable counterplan is to install drainage hole on the surface of slope in order to prevent erosion and debris flow.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.03a
• /
• pp.119-125
• /
• 2004

Unsteady nonlinear wave motions on the free surface over a plane beach of constant slope are numerically simulated using a finite difference method in rectangular grid system. Two-dimensional Navier-Stokes equations and the continuity equation are used for the computations. Irregular leg lengths and stars are employed near the boundaries of body and free surface to satisfy the boundary conditions. Also, the free surface which consists of markers or segments is determined every time step with the satisfaction of kinematic and dynamic free surface conditions. Moreover, marker-density method is also adopted to allow plunging jets impinging on the free surface. The second-order Stokes wave theory and solitary wave theory are employed for the generation of waves on the inflow boundary. For the simulation of wave breaking phenomena, the computations are carried out with the plane beach of constant slope in surf zone. The results are compared with each other. The marker-density method is better then the hybrid method. Also they are compared with other existing experimental results. The Agreement between the experimental data and the computation results is good.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.1 no.1
• /
• pp.63-69
• /
• 1998

The slope revegetation methods in Korea are generally the hydroseeding mixed with perennial herbs, soil, fibers, and fertilizer in consideration of scenic landscape rather than ecological and engineering effect. But perennial herbs can't protect the slope from deep surface erosion and they are not tall enough to create the original naturalness at the boundary parts of existing woodlands. This study is about the slope revegetation method using nutritional propagation capacity of plants and the experimental construction was carried out on the cut-slope of Yongin Hoam C.C. We dug several trenches to a depth of 80cm and at intervals of 150cm from each other. After placing various kinds of live branches(Salix species) into the trench, we backfilled with the excavated soils and finally sprayed water mixed with soil-stabilizer, fertilizer. As six months passed, we made a vegetation research and check the slope surface erosion. Vegetation research was performed in examining the frequency of each block using transect method. 31 kinds of plant species appeared in total area($113.6m^2$) and the dominant species are Setaria viridis, Artemisia rubripes, Persicaria pubescens, Plantago asiatica, Cyperus amuricus, Commelina communis. Among the examined blocks, '아', the top part of the slope, showed the ratio of 1.4 as the highest Alpha-diversity. With regard to life form, therophytes were shown dominant distribution of 58% of total species and neophytes relatively low distribution of 16%. It can be estimated that there is no ecological stabilization of this slope, because of ruderal species' occupation of 74% in total area. Regarding the slope stabilization, the serious surface erosion didn't take place in spite of heavy rainfall this year, but a little surface erosion took place at the block where no other species coming from outside of the site were found.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.3 no.1
• /
• pp.1-9
• /
• 2000

The purpose of this study was to analyze the characteristics of soil erosion on the fill-slope of forest road by elapsed years after road construction. Thirteen plots were established on the fill-slope of the newly-constructed forest road, and surveyed for two years(1997~1998). In these plots, the data about soil erosion, surface runoff, vegetation coverage, slope structural characteristics and rainfall were collected. In 1997, the major causes for soil erosion were found by the correlation coefficients with the amount of surface runoff from the fill-slope, vegetation coverage, slope length, slope degree, total rainfall and max. 1 hour rainfall. But, in 1998, the major causes for soil erosion were vegetation coverage and slope degree. Using the stepwise multiple regression method, in 1997, the amount of soil erosion from the fill-slope was complexly expressed as a exponential function of statistically significant the amount of surface runoff from the fill-slope, total rainfall, slope degree of fill-slope and vegetation coverage, but, in 1998, simply expressed as a exponential function of vegetation coverage.

• The Journal of Engineering Geology
• /
• v.16 no.2 s.48
• /
• pp.189-199
• /
• 2006

This paper presents a field study of the stability of slope collapsed during road construction and proposes a reasonable countermeasure if the current slope is unstable. As a result of slope investigation, it was found that the slope includes five tension cracks and the sliding surface is started from the tension crack and propagated the surface soil layer through weathered rock layer. The slope stability analyses are conducted in case of dry and rainfall seasons. The results indicate that the slope is unstable status. A reinforcement method of slope failure should be selected according to the scale of failure. That is, the scale of slope failure, which is classified small, middle and large size determines the reinforcement method of slope. Since the slope interested in this study is large size failure slope, the reinforcement method to control slope failure is selected stabilizing piles, and seed spray and drainage of surface waterare also selected to remain the factor of safety. The SLOPILE (Ver. 3.0) program is applied in order to do stability analysis of slope reinforced by piles. As the result of analysis, the slope reinforced by a row of piles shows the stable state. It is clearly confirmed that the stabilizing of piles can improve the stability of slope.

• Geomechanics and Engineering
• /
• v.21 no.6
• /
• pp.513-525
• /
• 2020

Slopes stabilised with piles are seldom analysed considering uncertainties in the parameters of the pile-slope system. Reliability analysis of the pile-slope system quantifies the degree of uncertainties and evaluates the safety of the system. In the present study, the reliability analysis of a slope stabilised with piles is performed using the first-order reliability method (FORM) based on Hasofer-Lind approach. The implicit performance function associated with the factor of safety (FS) of the slope is approximated using the response surface method. The analyses are carried out considering the design matrices formulated based on both the 2^k factorial design augmented with a centre run (2^k fact-centred design) and face-centered cube design (FCD). The finite element method is used as the deterministic model to compute the FS of the pile-slope system. Results are compared with the results of the Monte Carlo simulation. It is observed that the optimum location of the row of piles is at the middle of the slope to achieve the maximum FS. The results show that the reliability of the system is not uniform for different pile configurations, even if the system deterministically satisfies the target factor of safety (FS_t) criterion. The FS_t should be selected judiciously as it is observed that the reliability of the system changes drastically with the FS_t level. The results of the 2^k fact-centred design and FCD are in good agreement with each other. The procedure of the FCD is computationally costly and hence the use of 2^k fact-centred design is recommended, provided the response of the system is sufficiently linear over the factorial space.

• Structural Engineering and Mechanics
• /
• v.89 no.3
• /
• pp.253-263
• /
• 2024

Slope stability is generally paid more attention to in slope protection works, especially for slope containing weak layers. Two indexes of safety factor and failure model are selected to perform slope stability. Moreover, the finite element limit analysis method comprehensively combines the advantage of the limit analysis method and the finite element method obtaining the upper and lower bounds of the safety factor and the failure mode under the slope stability limit state. In this study, taking a waste dump containing a weak layer as an engineering background, the finite element limit analysis method is adopted to explore the potential failure mode. Meanwhile, the sensitivity analysis of slope stability is performed on geometrical and geotechnical parameters of the waste dump. The results show that the failure mode of the waste dump slope is two wedges if the weak layer is located on the ground surface (Model A), while the slope can be observed as three wedges failure if the weak layer is below the ground surface (Model B). In addition, both failure modes are highly sensitive to the friction angle of the weak layer and the shear strength of waste disposal, and moderately sensitive to the heap height, the dip angle and cohesion of the weak layer, while the toe cutting has limited effect on the slope stability. Moreover, the sensitivity to the excavation of the ground depends on the location of the weak layer and failure mode.