• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1442-1446
• /
• 2004

The heat (mass) transfer characteristics on the blade surface of a first-stage turbine rotor cascade has been investigated by employing the naphthalene sublimation technique. A four-axis profile measurement system is employed for the measurements of the local heat (mass) transfer coefficient on the curved blade surface. The experiments are carried out for two free-stream turbulence intensities of 1.2% and 14.7%. The high free-stream turbulence results in more uniform distributions of heat load on the both pressure and suction surfaces and in an early boundary-layer separation on the suction surface. The heat (mass) transfer enhancement on the suction surface due to the endwall vortices is found to be relatively small under the high free-stream turbulence.

• 한국정밀공학회지
• /
• 제12권1호
• /
• pp.5-14
• /
• 1995

An optical measurement method of three dimensional surface profiles which is named the slit beam projection is suggested and practically implemented. This method is intended especially for noncontact and fast digitization of sculptured surfaces for CAD modeling and die manufacturing. Its basic principles are based on geometric optics. Deatiled optical principles and an sub-pixel image processing technique to enhance the measuring resolutions are described in this study. The measuring performances of the slit beam projection are presented and discussed to demonstrate that an actual measuring accuracy of below .+-. 0.2mm can be achived over the whole measuring range(500mm*300mm*200mm)

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 춘계학술대회 논문집
• /
• pp.12-12
• /
• 2010

The hall probe measurement system was used to measure the critical current distribution of superconducting coated conductor. The system consists of reel to reel moving apparatus, 7 array hall probe, a rotary encoder and permanent magnet. The magnetic field profile across the width of superconducting coated conductor using Bean's critical state model was calculated. The effect of various parameters of the formulas on the magnetic field distribution and the effect of shape and size of artificial defects, which were formed on the surface of SmBa2Cu3O7-d(SmBCO) coated conductor using laser marking system, on the hall probe magnetic field signal of the hall probe measurement system was investigated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.445-449
• /
• 2001

The tool wear that is developed by long-term machining in mold manufacturing with machining center makes a severe influence to the accuracy and the surface roughness. In this reason, tool-wear supervising system which has guaranteed high accuracy and high speed is needed to improve the measurement quality. Touching probe and touch sensor are widely used to measure the tool profile at on-machine measurement. In this paper, using the newly developed electric touch point measuring system, the Automatic Tool Compensation System is developed to correct the error of tool diameter resulted from the wear, and the operating method of this system is also provided.

• 한국자동차공학회논문집
• /
• 제9권1호
• /
• pp.198-204
• /
• 2001

The shot peening is largely used for a surface treatment of metallic components where small spherical pellets called shots are blasted onto the surface with velocities up to 100 m/s. This treatment leads to improvement of fatigue behavior due to the developed compressive residual stresses, and so it has gained widespread acceptance I the automobile and aerospace industries. The residual stress profile on surface layer depends on the parameters of shot peening, which are, shot velocity, shot diameter, coverage, impact angle, material properties etc. and the method to confirm this profile is the measurement by X-ray diffractometer only. Despite the importance to automobile ad aerospace industries, little attention has been devoted to the accurate modelling of the process. In this paper, the simulation technique is applied to predict the magnitude ad distribution of the residual stress and plastic deformation caused by shot peening with the help of the finite element analysis.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.218-223
• /
• 2000

The shot peening is largely used for a surface treatment in which small spherical parts called shots are blasted on a surface of a metallic components with velocities up to 100m/s. This treatment leads to an improvement of fatigue behavior due to the developed compressive residual stresses, and so it has gained widespread acceptance in the automobile and aerospace industries. The residual stress profile on surface layer depends on the parameters of shot peening, which are, shot velocity, shot diameter, coverage, impact angle, material properties etc. and the method to confirm this profile is only measurement by X-ray diffractometer. Despite its importance to automobile and aerospace industries, little attention has been devoted to the accurate modelling of the process. In this paper, the simulation technique is applied to predict the magnitude and distribution of the residual stress and plastic deformation caused by shot peening with the help of the finite element analysis.

• 한국수자원학회논문집
• /
• 제33권2호
• /
• pp.169-179
• /
• 2000

이 연구에서는 1995년부터 1997년까지 금강수계 강경지점에서 유속계로 측정한 유속자료를 분석하여 자연하천의 연직방향 유속분포특성을 규명하였다. 또한, 현장유속 측정조건이 불량하여 다점법으로 유속분포를 측정하기 곤란한 경우, 간단하게 표면유속만을 측정하여 상대깊이별 유속을 추정할 수 있는 연직 유속분포식을 유도하였다. 2차 포물선의 유속분포식은 통계적으로 매우 안정적이고, 표면유속과 바닥유속 등과 고도의 유의성을 보였다. 2차 포물선식의 상수 및 계수와 표면유속과의 상관관계를 구하였으며, 실측 검정자료에 적용한 결과, 유속분포특성을 잘 반영하는 것을 확인할 수 있었다. 연직 유속분포식으로 추정된 유속은 실제수심을 적용하여 평균유속과 유량을 결정할 수 있으며, 이는 또한 하천의 오염물질이동 등 수질해석에 적용할 수 있을 것이다.

• 전기화학회지
• /
• 제2권1호
• /
• pp.23-26
• /
• 1999

백금$(Pt)/0.1M\;H_2SO_4$, 전해질 계면에서 교류임피던스 측정과 위상이동 방법을 사용하여 Langmuir 흡착등온식을 정성적으로 해석하였다. 위상이동$(\phi)$은 음전위(E<0)와 주파수(f)에 따르며, Pt 일전극(음극)에 흡착된 수소원자$(H_{ads})$의 표면피복율$(\theta)$에 반비례한다. 중간주파수대$(1\~100 Hz)$에서 위상이동 변화$(\phi\;vs.\;E)$는 Langmuir 흡착등온식$(\theta\;vs.\;E)$의 계산과 해석에 사용할 수 있는 실험적인 방법이다. $Pt/0.1M\;H_2SO_4$ 전해질 계면에서 흡착평형상수(K)와 표준자유에너지$({\Delta}G_{ads})$는 각각 $3\times10^{_4}$와 20.1kJ/mol이다.

• Transactions on Electrical and Electronic Materials
• /
• 제7권3호
• /
• pp.118-122
• /
• 2006

Diamond-like carbon (DLC) films were prepared on silicon substrates by the RF PECVD (Plasma Enhanced Chemical Vapor Deposition) method using methane $(CH_4)$ and hydrogen $(H_2)$ gas. We examined the effects of the post annealing temperature on the tribological properties of the DLC films using friction force microscopy (FFM). The films were annealed at various temperatures ranging from 300 to $900^{\circ}C$ in steps of $200^{\circ}C$ using RTA equipment in nitrogen ambient. The thickness of the film was observed by scanning electron microscopy (SEM) and surface profile analysis. The surface morphology and surface energy of the films were examined using atomic force microscopy and contact angle measurement, respectively. The hardness of the DLC film was measured as a function of the post annealing temperature using a nano-indenter. The tribological characteristics were investigated by atomic force microscopy in FFM mode.

• Structural Engineering and Mechanics
• /
• 제25권5호
• /
• pp.565-576
• /
• 2007

The article describes a technique for the measurement of the level of complexity of fracture surfaces by the method of vertical sections, and a performed statistical analysis of the effect of profile lines on the fractographic and fractal parameters of fractures, i.e. the profile line development factor, $R_L$, and the fracture surface development factor, $R_S$, (as defined by the cycloid method), as well as the fractal dimension, $D_C$, (as determined by the chord method), and the fractal dimension, $D_{BC}$, (as determined by the box method). The above-mentioned parameters were determined for fracture surfaces of basalt and gravel concretes, respectively, which had previously been subjected to fracture toughness tests. The concretes were made from mixtures of a water/cement ratio ranging from 0.41 to 0.61 and with a variable fraction of coarse aggregate to fine aggregate, $C_{agg.}/F_{agg.}$, in the range from 1.5 to 3.5. Basalt and gravel aggregate of a fraction to maximum 16 mm were used to the tests. Based on the performed analysis it has been established that the necessary number of concrete fracture profile lines, which assures the reliability of obtained testing results, should amount to 12.