• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.31-35
• /
• 2002

It is hard to expect excellent electrical, mechanical and chemical properties from most of the composite materials presently used as insulators due to insufficient wettability property caused by the difference of interfacial properties between the matrix material and the reinforcer. Therefore, various interfacial coupling agents have been developed to improve the interfacial properties of composite materials. But if the wettable coupling agents are used outdoor for a long time, change in quality takes place in the coupling agents themselves, bringing about deterioration of the properties of the composite materials. In this study, composite materials were put to dry interfacial treatment by use of plasma technology. It has been presented that the optimum parameters for the best wettability of the samples at the time of generation of plasma were oxygen atmosphere, 0.1 torr of system pressure, 100 W of discharge power, and 3 minutes of discharge time. Also, the surface resistance rate and dielectric property were improved.

• 한국표면공학회지
• /
• 제44권6호
• /
• pp.246-249
• /
• 2011

Surface modification before coating nickel by coupling agents and/or etchant of glass did not provide enough adhesive strength of electroless nickel deposits on glass. Effect of heat treatments on hardness as well as adhesion of nickel deposits was studied by using tape test for adhesion, nanoindenter for hardness and glancing angle x-ray diffractometer (GAXRD) for phase characterization. Heat treatment improved hardness as well as adhesion. XRD results give that the improvements of adhesion and hardness are due to the formation of $NiSiO_4$ around the interface between the nickel deposits and the glass and the precipitation of $Ni_3P$ causing precipitation hardening, respectively. The details in effects of heat treatment on adhesion and hardness are described here.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.3-23
• /
• 2017

The achievement of tissue engineering can be highly depending on the capability to generate complicated, cell seeded three dimensional (3D) micro/nano-structures. So, various fabrication techniques that can be used to precisely design the architecture and topography of scaffolding materials will signify a key aspect of multi-functional tissue engineering. Previous methods for obtaining scaffolds based on top-down are often not satisfactory to produce complex micro/nano-structures due to the lack of control on scaffold architecture, porosity, and cellular interactions. However, a bioprinting method can be used to design sophisticated 3D tissue scaffolds that can be engineered to mimic the tissue architecture using computer aided approach. Also, in recent, the method has been modified and optimized to fabricate scaffolds using various natural biopolymers (collagen, alginate, and chitosan etc.). Variation of the topological structure and polymer concentration allowed tailoring the physical and biological properties of the scaffolds. In this presentation, the 3D bioprinting supplemented with a newly designed plasma treatment for attaining highly bioactive and functional scaffolds for tissue engineering applications will be introduced. Moreover, various in vivo and in vitro results will show that the fabricated scaffolds can carry out their structural and biological functionality.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.417-421
• /
• 2006

In this study, colloidal Ag solution was spouted on the surface of the inorganic pigment using the hybridizer system and the spray nozzle. Then, the surface of the inorganic pigment was modified by titanium dioxide in order to possess antibacterial ability. Nano-sized colloidal Ag was made by using a seed sol method in this study. It was confirmed that the size of particle per unit weight becomes enlarged, as the addition of $AgNO_{3}$ increased, and as the time of reaction increased, in the manufacturing process of nano-sized colloidal Ag. The antibacterial measurement of the inorganic pigment showed that the growth of fungus was reduced as the reaction time increased. It was measured that the antibacterial activity was excellent at fixed time frame, after the antibacterial ability appeared in $5{\sim}7$ hours of the antibacterial inoculation experiment. The experiment of titanium dioxide's Photocatalyst effect showed $60{\sim}70%$ efficiency in about 80 minute reaction time of the dissolution results regarding measurements of benzene. It was shown that more than 90% of the dissolution efficiency was achieved in the reaction time of about 30 minute.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.162-168
• /
• 2011

In this research, nitrogen plasma source ion implantation(PSII) of non-coated tungsten carbide endmill tools was conducted with low heat treatment for increasing wear resistance. After the low heat treatment of PSIIed tools to give a homogeneity of wear resistance, the surface modification of tools was analyzed by hardness test, surface roughness and cutting forces. As for the resultant cutting forces, low heat treatment in temperature of $400^{\circ}C$ and $500^{\circ}C$ is stable because of low cutting resistance. The 20-minutes heat treated tool at spindle speed 25000rpm has superiority of surface roughness, Ra of $0.420{\mu}m$ and was found to have good wear resistance. The higher hardness value was obtained by increasing temperature from $300^{\circ}C$ to $600^{\circ}C$ for PSIIed tools with low heat treatment. As the PSIIed tools under 10minutes at temperature of $600^{\circ}C$ have the highest hardness as Hv of 2349.8, It was analyzed that temperature processing give much influences on hardness.

• 펄프종이기술
• /
• 제34권3호
• /
• pp.9-16
• /
• 2002

The adsorption characteristics and surface energetics of hydrophobically modified MCC have been investigated by the inverse gas chromatography technique at infinite dilution. The thermodynamic parameters of adsorption, ΔG, ΔH and ΔS, for n-alkanes were determined at infinite dilution. Heats of adsoption of the n-alkanes increased as the level of hydrophobic modification increased. The hydrophobically modified MCC also showed greater entropy of adsorption indicating restricted mobility of the adsorbed n-alkanes. The acid/base characteristics of the MCC were evaluated using polar probes. As the hydrophobicity of MCC increased, the basisity of the MCC decreased.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.450-450
• /
• 2011

This study reports the hydrogen sulfide gas sensing properties of ZnO nanorods bundle and the investigation of gas sensing mechanism. Also the improvement of sensing properties was also studied through the application of ZnO heterstructured nanorods. The 1-Dimensional ZnO nano-structure was synthesized by hydrothermal method and ZnO nano-heterostructures were prepared by sonochemical reaction. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) spectra confirmed a well-crystalline ZnO of hexagonal structure. The gas response of ZnO nanorods bundle sensor increased with increasing temperature, which is thought to be due to chemical reaction of nanorods with gas molecules. Through analysis of X-ray photoelectron spectroscopy (XPS), the sensing mechanism of ZnO nanorods bundle sensor was explained by well-known surface reaction between ZnO surface atoms and hydrogen sulfide. However at high sensing temperature, chemical conversion of ZnO nanorods becomes a dominant sensing mechanism in current system. In order to improve the gas sensing properties, simple type of gas sensor was fabricated with ZnO nano-heterostructures, which were prepared by deposition of CuO, Au on the ZnO nanorods bundle. These heteronanostructures show higher gas response and higher current level than ZnO nanorods bundle. The gas sensing mechanism of the heteronanostructure can be explained by the chemical conversion of sensing material through the reaction with target gas.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.165-166
• /
• 2012

표면의 젖음성은 어플리케이션의 매우 중요한 점으로, 이것은 표면에너지와 표면의 조도에 의해 결정된다. 표면의 젖음성을 낮추기 위하여 저온 PECVD 공정을 통해 초소수성 박막을 만들었다. $SiO_xC_yH_z$ 필름을 만들기 위하여 RF power을 사용하였고, HMDS (hexamethyl-disilazane) precursor과 함께 수소 기체를 통해 증착하였다. 이 실험에서는 수소와 RF power를 변수로 진행하였고, 이것은 소수성 박막의 표면에너지를 변화시켰다. 필름을 합성한 후 contact angle measurement 및 AFM을 사용해 표면에너지와 표면조도를 관찰하였다. 또한 필름의 화학적 결합을 알기 위해 FT-IR을 이용하였다. 여기에서 표면의 에너지는 표면의 조도와 화학적 결합상태에 의해서 영향을 받았음을 알 수 있었다.

• 한국세라믹학회지
• /
• 제36권7호
• /
• pp.691-697
• /
• 1999

TiO2 powder was adsorbed on the surface of mica using the heterocoagulation method in water TiO2 powder was prepared from hydrolysis of titanium-iso propoxide in a mixed solvent of anhydrous ethanol and water. When the molar ratio of water to titanium iso-propoxide was 0.25 monodispersed spherical TiO2 particles were obtained. The prepared TiO2 powder showed anatase phase after heat treatment at 50$0^{\circ}C$ for 2 h and then transformed to rutile phase after heat treatment at 100$0^{\circ}C$ for 2h. The iso-electric points of TiO2 and Mica were pH 3.9 and pH 3.25 respectively which were measured by the Z-potential analysis in water base. The maximum Z-potential difference between two powders was observed in the range of pH 3.6~3.7 TiO2 powder was adsorbed on the surface of mica by heterocoagulation method in pH 3.6~3,7 The properties of prepared TiO2 powder was haracterized by TG-DTA, XRD and SEM The morphology and thermal properties of TiO2-adsorbed mica were examined.

• 폴리머
• /
• 제28권6호
• /
• pp.538-544
• /
• 2004

Z-라이신 올리고머를 사슬연장제로 하고 D-다이페닐이소시아네이트와 폴리테트라메틸글리콜을 반응시켜 주사슬에 L-라이신 분절을 함유하는 폴리우레틴 (PULL)을 합성하였다. PULL 표면의 아민기와 인슐린의 공유 결합으로 인슐린 고정화 폴리우레탄 (PULL-In)을 제조하였다. Bradfold법으로 측정한 고정화 인슐린의 양은 약 0.30 nmol/$\textrm{cm}^2$이였다. $^3$H-thymidine 분석방법과 광학 현미경법으로 NIH/3T3 섬유아세포와 표면 개질된 PULL의 상호작용을 조사하였다. 그 결과 PULL-In 필름 표면에서의 세포 성장 속도는 다른 기질에서보다 높았다. 또한 고정화된 인슐린에서의 세포증식이 배양액에 용해된 인슐린에서와 거의 유사한 특성을 나타내었다.