• Journal of the Korean Chemical Society
• /
• v.60 no.5
• /
• pp.317-320
• /
• 2016

Efficient copper removal from water was achieved by using surface modified silica spheres with 3-mercaptopropyltrimethoxysilane (MPTMS) using base catalyst. The surface modification of silica spheres was performed by hydrolysis and condensation reactions of the MPTMS. The characteristic infrared absorption peaks at 2929, 1454, and 1343 cm⁻¹ represent the −CH₂ stretching vibration, asymmetric deformation, and deformation, respectively. The absorption peaks at 2580 and 693 cm⁻¹ corresponding the −SH stretching vibration and the C-S stretching vibration indicate the incorporation of MPTMS to the surface of silica spheres. Field emission scanning electron microscope (FESEM) image of the surface modified silica sphere (SMSS) shows nano-particles of MPTMS on the surface of silica spheres. High concentration of copper solution (1000 ppm) was used to test the copper removal efficiency and uptake capacity. The FESEM image of SMSS treated with the copper solution shows large number of copper lumps on the surface of SMSS. The copper concentration drastically decreased with increasing the amount of SMSS. The residual copper concentrations were analyzed using inductively coupled plasma mass spectrometer. The copper removal efficiency and uptake capacity with 1000 ppm of copper solution were 99.99 % and 125 mg/g, respectively.

• Journal of Mechanical Science and Technology
• /
• v.20 no.11
• /
• pp.1942-1949
• /
• 2006

Typically, condensate forms as droplets on the fin surfaces and may bridge the space between the fin surfaces. This is due to the dry characteristics inherent to the fin surface. The droplets increase the air-side pressure drop. In the case of high air velocities, these droplets may be blown off the fins and entrained in the air stream. To minimize the formation of condensate droplet, the wet ability of the fins must be improved. The carry-over velocity is affected by fin surface characteristics. To avoid carry-over in the air conditioner having the highest air velocity of 1.5 m/sec, the dynamic contact angle (DCA) should be at least lowly under $60^{\circ}$.

• Applied Microscopy
• /
• v.46 no.4
• /
• pp.201-205
• /
• 2016

Functional surfaces in nature have been continuously observed because of their ability to adapt to the environment. To this end, methods such as scanning electron microscopy (SEM) have been widely used, and their wetting functions have been characterized via environmental SEM. We investigated the superhydrophobic hairy leaves of Pelargonium tomentosum, i.e., peppermint-scented geranium. Their surface features and wettability were studied at multiple-scales, i.e., macro-, micro-, and sub-micro scales. The surfaces of the investigated leaves showed superhydrophobicity at the macro-, and micro-scales. The wetting or condensing behavior was studied for molecule-size water vapors, which easily adhered to the hairy surface owing to their significantly lower size in comparison to that of the surface.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.3
• /
• pp.297-302
• /
• 1999

In situ measurement of infrared absorption spectra has been performed during low-temperature plasma-enhanced chemical vapor depositiion of silicon-oxide films using tetramethoxysilane as a silicon source. Several absorption bands due to the reactant molecules are clearly observed before deposition. In the plasma, these bands completely disappear at any oxygen mixing ratio. This result shows that most of the tetramethoxysilane molecules are dissociated in the rf plasma, even C-H bonds. Existence of Si-H bonds in vapor phase and/or on the film surface during deposition has been found by infrared diagnostics. We observed both a decrease in Si-OH absorption and an increase in Si-O-Si after plasma off, which means the dehydration condensation reaction continues after deposition. The rate of this reaction is much slower than the deposition ratio of the films.

• Analytical Science and Technology
• /
• v.19 no.2
• /
• pp.121-130
• /
• 2006

In this study, silver pre-treated activated carbons are transformed using sulfuric acid. From the results of adsorption, each isotherm shows a distinct knee band, which is characteristic of microporous adsorbents with capillary condensation in micropores. In order to reveal the causes of the differences in adsorption capacity and specific surface area after the samples were washed with various strengths of sulfuric acid, surface morphology and external pore structure were investigated by SEM. X-ray diffraction patterns indicated that Ag-activated carbons show better performance for silver and silver compounds removal by post-treatment with acid. The FT-IR spectra of silver-activated carbon samples show that the acid post-treatment was consequently associated with the removal of silver with an increased surface functional group containing oxygen of the activated carbon. The type and quality of oxygen groups are determined on the method proposed by Boehm. For the chemical composition microanalysis of silver-activated carbons transformed by post-treatment with sulfuric acid, samples were analyzed by EDX.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.121-125
• /
• 2000

An ozone condenser by a selective adsorption on the silica gel surface is constructed. Ozone density is evaluated by three methods; ultraviolet absorption, thermal decomposition and Q-mass analyzing methods. Thermal decomposition method is found to be available to the density evaluation from dilute to highly condensed ozone. The highest ozone density condensed by the adsorption method is evaluated to be 97 mol%.

• The Journal of the Korean dental association
• /
• v.18 no.2 s.131
• /
• pp.115-119
• /
• 1980

The purpose of this study was to observe clinical behavior on a national dispersant amalgam alloy, KISTCAP which newly developed by the KIST (Korea Instute for Science and Technology) in Korea. The results were as follows: 1. There was no significant difference in manipulating between the above mentioned alloy and the conventional lathe cut alloy. 2. The condensation pressure for this alloy was relatively less than that of conventional one. 3. More time was needed to polish the surface of this amalgam filling body than the conventional one. 4. No notable difference was seen in the over-all clinical behavior between the Whitecap and kistcap, except the latter one showed a little more tendency in redish color.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.10a
• /
• pp.687-688
• /
• 2005

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.143-144
• /
• 2002

A series of alcohols with perfluorinated segments $F(CF_2)_m(CH_2)_n-OH$, with m=8, 10 and n=4, 6, 10, were synthesized. First, the alcohols were reacted with fatty acid to produce several esters $(F(CF_2)_m(CH_2)-OOC-R$ with m=8, 10 and n=2, 4, 8,) containing perfluoro group by condensation reaction, and characterized by FT-IR, GC, and surface tension. The esters were soluble in ethyl ether, toluene, hexane, ethyl acetate, chloroform, and acetone, but insoluble in methyl alcohol, ethyl alcohol and isopropyl alcohol. Preliminary experiments on 1,2-dichloroethane solutions showed a remarkable decrease of surface tension upon addition of the esters. Also, the esters films ranged from 100 to $122^{\circ}$, depending on the structure of fatty acid esters. As the separate experiment, the water-repellency of coated paper and cotton was evaluated. As a result, the water droplet dropped in surface was not permeated for two weeks.

• Carbon letters
• /
• v.7 no.1
• /
• pp.34-41
• /
• 2006

The objective of this paper is to compare the variation of surface properties by hydrochloric acid pre-treatment and of metallic potassium and their salts loading effect for activated carbon after surfaces transformation by acid. From the results of nitrogen adsorption, each isotherm shows a distinct knee band, which is closely related to the characteristic of microporous carbons with capillary condensation in micropores. In order to present the causes of the differences in surface properties and $S_{BET}$ after the samples were treated with hydrochloric acid, pore structure and surface morphology are investigated by adsorption analysis. X-ray diffraction (XRD) patterns indicate that activated carbons show better performance for metallic potassium and potassium salts by pre-treatment with hydrochloric acid. Scanning electron microscopy (SEM) pictures of potassium/activated carbon particles provide information about the homogeneous distribution of metal or metal complex on the surface. For the chemical composition microanalysis for potassium treatment of the activated carbon pre-treated with hydrochloric acid, samples were analyzed by energy disperse X-ray (EDX). Finally, the type and quality of oxygen groups are determined from the method proposed by Boehm. A positive influence of the acidic groups on the carbon surface by acid treatment is also demonstrated by an increase in the contents of potassium salts with increasing of acidic groups calculated from Boehm titration.