• Textile Coloration and Finishing
• /
• v.18 no.2 s.87
• /
• pp.1-7
• /
• 2006

In order to prepare PAN nano fiber web, PAN/DMF solution was prepared and electrospun. The diameter of fiber was depended on the polymer concentration (7.5-15wt%) and the applied voltage (10-16kV). The average diameter of fiber increased with an increase of the polymer concentration and decreased with the applied voltage. At 7.5wt% concentration, many beads were found. So, we prepared a nano PAN fiber by electrospinning at concentration of 10wt% and 16kV. PAN fibers were reduced with litium aluminium hydride and the dyeability to acid dye was checked. The reduced nano PAN fiber showed much better dyeability compared with the reduced ordinary PAN fiber. It was considered that the increase of specific surface area have an important role in dyeing with acid dye.

• Carbon letters
• /
• v.1 no.1
• /
• pp.17-21
• /
• 2000

Catalytic reduction and oxidation of NO over polyacrylonitrile based activated carbon fibers (PAN-ACF) under various conditions were carried out to develop removal process of NO from the flue gas. The effect of temperature, oxygen concentration and the moisture content for the reduction of NO with ammonia as a reducing agent was investigated. The reduction of NO increased with the oxygen concentration, but decreased with the increased temperature. The moisture content in the flue gas affects the reduction of NO as the inhibition of the adsorption of the other components and the reaction on the surface of ACE For the oxidation of NO to $NO_2$ over PAN-ACF without using a reducing gas, it showed the temperature and the oxygen concentration of the flue gas are the important factors for the NO conversion in which the conversion increased with oxygen concentration and decreased with the temperature increase and might be the alternative option for the selective catalytic reduction process.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.10
• /
• pp.891-895
• /
• 2013

This paper proposes the development of a new method for online analysis which measured acid concentration in a pickling line. Pickling is the most important step to remove surface scale layers and is strongly depending on the exactly controlled pickling liquor composition. Today, there is no feasible system available for the online control of pickling lines. Within this paper, new methods for online analysis of pickling liquors have been tested and implemented into an overall pickling process control tool. This method measured simultaneously the hydrochloric acid and iron ion concentration in a solution of hydrochloric acid by measuring the ultrasonic speed, the solution temperature, and the electrical conductivity. Experimental results showed excellent precision and the measurement error was ${\pm}2g/l$ compared with the neutralization titration measurement.

• Journal of Environmental Science International
• /
• v.5 no.1
• /
• pp.35-41
• /
• 1996

For studying of coagulation and sedimentation in estuarine clay, we obtained several flow curves with various concentrations of sea water by using Coutte type rotational rheometer. The initial shear stress on high concentration of sea water was observed big, but after this, its value is decreasing with increasing shear rate. The maximum pick of shear stress is decreasing with the decreasing of concentration of sea water The trend is same totally above for viscosity. The sedimentation times with the concentration of sea water vary in $\infty$ ~ 5 minutes. The zeta potential is changed dramatically between 114 and 118 concentration of sea water. That is consistent with the sedimentation graph. From these results, the phenomena of coagulation and sedimentation can be explained with viscoelastic terms on structual formation among particles by the changes of surface potential affected from contacting sea water to dispersed particles.

• Textile Coloration and Finishing
• /
• v.19 no.5
• /
• pp.30-36
• /
• 2007

Cypermethrin-containing polyurea microcapsules were prepared by interfacial polymerization using aromatic 2,4-toluene diisocyanate(TDI) and Ethylene diamine(EDA) as wall forming materials. The effects of the protective colloids of polyvinylalcohol(PVA) and gelatin were investigated through experimentation. The mean size of the polyurea microcapsules was smaller and the surface morphology of the PVA was much smoother than gelatin. In addition the release behavior was much more controlled and better sustained. As the concentration of protective colloid increased, the wall membrane of the polyurea microcapsules became more stable, the thermal stability of the wall membrane increased, the mean particle size became smaller, and the particle distribution was more uniform. The release behavior of the core material changed according to the concentration. As the gelatin concentration was increased, a more controlled and sustained release behavior was observed. However, in the case of PVA, the increase of PVA concentration lead to a more rapid release rate.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.2
• /
• pp.189-193
• /
• 2001

The irreversible capacities caused by the reduction of solvent on the surface of a negative electrode (KMFC:Kawasaki Mesophase Fine Carbon) were examined during the initial cycle in ethylene carbonate (EC)-diethyl carbonate (DEC) electrolyte solut ions at various concentrations of LiPF6. Chronopotentiograms, linear sweep voltammograms, and impedance spectra clearly showed differences in irreversible capacity and that those differences are related to the concentration of electrolyte during the initial charge. These differences were caused by the amount of solvent decomposition as a function of the concentration of LiPF6 electrolytic salt. The data are discussed with reference to the concentration of electrolytic salt and the properties of passivation film formed by solvent decomposition.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.2
• /
• pp.248-253
• /
• 1987

Boron diffusion into silicon through poly\ulcorneri-SiO2 was carried out for the diffusion with low concentration using CVD-BN. The result of direct boron diffusion from BN into silicon and that of boron diffusion through SiO2 from BN into silicon was compared with the result of boron diffusion through poly-Si-SiO2 from BN into silicon. In the case of boron diffusion through poly Si-SiO2, the low concentration diffusion was obtained, that is the boron surface concentration in silicon Cs=10**16 Cm**-3, and the glassy compounds were not seen.

• Corrosion Science and Technology
• /
• v.6 no.4
• /
• pp.154-158
• /
• 2007

For the application of flexible printed circuit board (FPCB), electroplated copper is required to have low surface roughness and residual stress. In the paper, the effects of surface roughness and residual stress of electroplated copper as thick as $8{\mu}m$ were studied on organic additives such as inhibitor, leveler and accelerator. Polyimide film coated with sputtered copper was used as a substrate. Surface roughness and surface morphology were measured by 3D-laser surface analysis and FESEM, respectively. Residual stress was calculated by Stoney's equation after measuring radius curvature of specimen. The addition of additives except high concentration of accelerator in the electrolyte decreased surface roughness of electroplated copper film. Such a tendency was explained by the function of additives among which the inhibitor and the leveler inhibit electroplating on a whole surface and prolusions, respectively. The accelerator plays a role in accelerating the electroplating in valley parts. The inhibitors and the leveler increased residual stress, whereas the accelerator decreased it. It was thought to be related with entrapped additives on electroplated copper film rather than the preferred orientation of electroplated copper film. The reason why additives lead to residual stress remains for the future work.

• KSBB Journal
• /
• v.27 no.3
• /
• pp.145-150
• /
• 2012

This study was accomplished using packed bed column reactors that contain nonsurface-modified polypropylene media and surface-modified media from hydrophobic surface property into hydrophilic property by ion beam irradiation. The objectives of this research was investigated the characteristics of organic compounds removal and microbe attachment from sewage of school cafeteria in these reactors. In 736.8 mg/L of the average inflow $COD_{Cr}$ concentration the reactors with and without surface modification showed 81.8% and 70.3% of average $COD_{Cr}$ removal efficiencies, respectively, which proves the $COD_{Cr}$ removal efficiency of surface-modified media reactor is higher than that of nonsurface-modified media reactor. After 90 days, there were maximum differences between modified system and non-modified system. In that time the maximum removal efficiency of $COD_{Cr}$ was 96.5% in modified system and was 85.2% in non-modified system that showed removal efficiency of surface-modified media system is 11.3% higher than that of nonsurface-modified media system. The average removal efficiency of SS was 80.4% for the surface modified system and 61.6% for the non-modified system under same condition. Also, the reactor of surface-modified media has advantage on microbe attachment and biofilm formation.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.11
• /
• pp.867-873
• /
• 2006

Vertical falling liquid film is extensively used in heat and mass transfer processes of many applications, such as evaporative coolers, cooling towers, and absorption chillers. In such cases, it is required that the falling film spreads widely in the surface forming thin liquid film to enlarge contact surface. An addition of surface active agent to a falling liquid film or hydrophilic surface treatment affects the fluid physical properties of the film. Surfactant addition not only decreases contact angle between the liquid and solid surface but also changes the surface from hydrophobicity to hydrophilicity. In this study, the effects of contact angle on falling film characteristics over a vertical surface have been investigated experimentally. The contact angle is varied either by an addition of surfactant to the liquid or by hydrophilic surface treatment. It is found that the wetted area is increased and film thickness is decreased by the hydrophilic treatment as compared with those of other surfaces. With this hydrophilic treatment, the falling liquid film spreads out widely in the surface. As surfactant concentration is increased, wetted area is also increased and the film thickness is substantially decreased.