• Journal of the Korean Society for Nondestructive Testing
• /
• v.10 no.2
• /
• pp.56-62
• /
• 1990

Surface Acoustic Waves(SAW) are generated on silicon wafer and $YZ-LiTaO_3$ substrate and are detected by noncontact method. As wave sources two kinds of transducers are used : the wedge-type of 20.0 MHz and fabricated Interdigital Transducer(IDT) of 20.8 MHz. SAW are modulated by the optical chopper frequency and are syncronized with a laser beam. In signal processing, intensity variations of light due to the intensity of SAW are analyzed using lock- in amplifier. From the results, corresponding to the applied input power, the intensity variations of a deflected light by corrugations on the substrates are increased and saturation phenomenon is observed.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.33-40
• /
• 2006

This paper presents a novel surface acoustic wave (SAW)-based pressure sensor, which is composed of single phase unidirectional transducer (SPUDT), three reflectors, and a deep etched substrate for bonding underneath the diaphragm. Using the coupling of modes (COM) theory, the SAW device was simulated, and the optimized design parameters were extracted. Finite Element Methods (FEM) was utilized to calculate the bending and stress/strain distribution on the diaphragm under a given pressure. Using extracted optimal design parameters, a 440 MHz reflective delay line on 41o YX LiNbO3 was developed. High S/N ratio, shan reflection peaks, and small spurious peaks were observed. The measured S11 results showed a good agreement with simulated results obtained from coupling-of-modes (COM) modeling and Finite Element Method (FEM) analysis.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.389-392
• /
• 1987

The energy gaps of undoped and Cr doped GaAs and $Al_{0-3}Ga_{0-7}As$ was measured nondestructively using surface acoustic wave (SAW) technique. The result is good agreement with other reported result. This technique is inexpensive and simple one for the measurement of mole fraction of $Al_xGa_{1-x}As$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.05a
• /
• pp.90-93
• /
• 1994

A surface acoustic wave(SAW) sensor for the detection of odorants has been constructed by depositing various phospholipids and fatty acids onto the surface of the SAW device. Applying the Langmuir-Blodgett technique. it was possible to deposit the optimal number of layer which was found to be between 10 and 20. The characteristics of a SAW device operating at 310 MHz deposited with phosphatidyl choline were analysed. Menthone, amylacetate, acetion, and other organic gases sho7\\\\`ed different affinities to the coated lipids. An explanation is given for differant odorant affinities based on the monolayer properties of phospholipids. The identification of odorants depending on the type of lipid used for coating is discussed in terms of a comparison of their normalized resonant frequency chi It pat terns. Using a number of different lipid-coated SAW devices. odorants can be identified by a computerized pattern recognition algorithm.

• Journal of Advanced Navigation Technology
• /
• v.12 no.2
• /
• pp.139-145
• /
• 2008

There has been lots of studies on communication systems using millimeter wave recently in many countries, specially in newly assigned 57GHz ~ 64GHz ISM band. Among those studies, IEEE 802.15.3c standard proposes OFDM (Orthogonal Frequency Division Multiplexing) systems for high data rate transmission support. But OFDM method has the PAPR (peak-to-Average Power Radio) problem The PAPR problem is to decline the performance of the transmission system due to signals distorted severely when passing through nonlinear components such as ADC/DAC and power amplifiers. In order to solve the problem of P APR, this paper suggests SSC (Sine Soft Clipping) and analyzes the PAPR, CCDF, PSD, BER by applying SAW(Surface Acoustic Wave) filter and power amplifiers to IEEE 802.15.3.c OFDM WPAN systems.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.4
• /
• pp.64-73
• /
• 1995

We developed a surface acoustic wave (SAW) computer aided design (CAD) for mobile communication using Kaier window function. The systems are composed of modules for designing apodization weighted IDT-uniform IDT, withdrawal weighted IDT-withdrawal weighted IDT, and resonator type. The design of SAW bandpass with center frequencies from 222MHz to 343MHz were simulated by the developed CAD system. Although the method proposed in this paper is formulated primarily for SAW filters, it is equally applicable to finite impulse response (FIR) digital filter design.

• Journal of Sensor Science and Technology
• /
• v.14 no.3
• /
• pp.186-190
• /
• 2005

This paper describes the development of a surface acoustic wave gas sensor that is designed to detect volatile gas by monitering phase change of output signal as a function of time. The sensor consists of SAW oscillators with a center frequency of 100 MHz fabricated on $128^{\circ}$ Y-Z $LiNbO_{3}$ substrates. Experimental results, which show the phase change of output signal under the absorption of volatile gas onto sensors, are presented. The proposed sensor has the properties of high sensitivity compare to the conventional SAW gas sensor and chemical selectivity. Thus, it is thought these results are applicable for use in sensor array of an high performance electronic nose system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.11
• /
• pp.947-952
• /
• 2001

In this paper, a wideband SAW convolver using a parabolic horn waveguide was designed and its characteristics were investigated. The convolver was made with parabolic horn waveguide at compression ratio 9:1 for reducing propagation loss and for improving convolution efficiency between two input IDTs of center frequency 193.78 ㎒. The SAW convolver utilizing acoustic nonlinearities of piezoelectric material demonstrated that it can provide large S/N ratio and can be use for programmable matched filter(PMF) in spread spectrum communication system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.8
• /
• pp.1589-1595
• /
• 2007

Recently many communication systems ate adapting the OFDM(Orthogonal Frequency Division Multiplexing) for multimedia data services. However, OFDM has some problems that PAPR is increased when sub-carries are summed up with same phases. This problem causes severe signal distortions while the signal is passing through non-linear system such as power amplifier resulting in performance degradation of transmission system. In this paper, we use IF-Clipping method to solve PAPR problem and the signal distortion caused by clipping is limited by use of SAW (Surface Acoustic Wave) filter and power amplifier(TWTA). And we derive the optimal parameter(PAPR, Backoff) values to meet the spectrum mask of WiBro system.

• Proceedings of the KOSOMBE Conference
• /
• v.1991 no.05
• /
• pp.98-100
• /
• 1991

A sensitive surface acoustic wave (SAW) sensor for the detection of odorants has been constructed by depositing different phospholipids and fatty acids on the surface of the SAW device wi th the Langmuir-Blodgett technique. The characteristics of SAW device operating at 310 MHz deposited with phosphatidylcholine were analyzed. Amyl acetate, acetoin, menthone and other organic gases showed different affinities. The identification of odorants depending on the species of lipid used for coating is discussed in terms of the similarity of the normalized resonant frequency shift pattern. Using a number of different lipid-coated SAW devices, odorants could be identified by a neural-network pattern recognition with back-propagation algorithm.