• Journal of Wetlands Research
• /
• v.24 no.4
• /
• pp.367-376
• /
• 2022

LID technologies are capable of mitigating the negative impacts of non-point source (NPS) pollution generated in different land uses. Apart from the increase in point and non-point pollutant generation, highly developed and paved areas generally affect microclimate conditions. This study evaluated both the efficiency of Low Impact Development (LID) facilities in treating NPS pollutant loads as well as the unit pollutant loads (UPL) generated in various urban features (such as parking lots and highways). This investigation also looked at how LID technology helped to alleviate Urban Heat Island (UHI) conditions. As compared to the typical unit pollutant loads in South Korea, the unit pollutant loads at Kongju National University were relatively low, because of no classes, limited vehicular transmission, and low anthropogenic activities during vacation. After receiving treatment from the LID facilities, the effluent pollutant loads were significantly decreased. The sedimentation in filtration mechanisms considerably reduced the pollutant fractions in the influent. Additionally, it was shown that LID facilities' mean surface temperatures are up to 7.2℃ lower than the nearby paved environment, demonstrating the LID systems reducing the UHI impact on an urban area.

• Journal of the Korean Society of Radiology
• /
• v.17 no.1
• /
• pp.25-30
• /
• 2023

As 3D printing technology is used in the medical field, interest in metal materials is increasing. The Department of Radiation Oncology uses a shielding block to shield the patient's normal tissue from unnecessary exposure during electron beam therapy. However, problems such as handling of heavy metal materials such as lead and cadmium, reproducibility according to skill level and uncertainty of arrangement have been reported. In this study, candidate materials that can be used for metal 3D printing are selected, and the physical properties and radiation dose of each material are analyzed to develop a customized shielding block that can be used in electron beam therapy. As candidate materials, aluminum alloy (d = 2.68 g/cm³), titanium alloy (d = 4.42 g/cm³), and cobalt chromium alloy (d = 8.3 g/cm³) were selected. The thickness of the 95% shielding rate point was derived using the Monte Carlo Simulation with the irradiation surface and 6, 9, 12, and 16 energies. As a result of the simulation, among the metal 3D printing materials, cobalt chromium alloy (d = 8.3 g/cm³) was similar to the existing shielding block (d = 9.4 g/cm³) in shielding thickness for each energy. In a follow-on study, it is necessary to evaluate the usefulness in clinical practice using customized shielding blocks made by metal 3D printing and to verify experiments through various radiation treatment plan conditions.

• Journal of Life Science
• /
• v.32 no.4
• /
• pp.298-302
• /
• 2022

Sulforaphane is a sulfur-containing substance found in large amounts in cruciferous plants and has been reported in several studies to have anticancer effects. Kale is a representative cruciferous plant known as a superfood and is widely used as an ingredient in various dishes. In this study, in order to investigate a cultivation method for increasing kale's content of sulforaphane, kale was treated with geraniol or methyl jasmonate and water stressed during cultivation using a aeroponic culture system in a fully enclosed plant factory. Geraniol or methyl jasmonate were sprayed on the kale's leaf surface once a day for 2 days, and water deprivation stress was conducted for 3 days after 7 days from first treatment day. No difference in growth between control, geraniol, methyl jasmonate treated groups were observed during cultivation. The study results showed that the kale sulforaphane content increased by 60% in the group treated with geraniol compared to the control group and that the group treated with water deprivation stress in addition to geraniol showed a significant increase of 414%. These results show that kale with an increased content of sulforaphane can be grown and that geraniol can be a good research material for increasing the content of functional substances in plants.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.2
• /
• pp.15-25
• /
• 2024

In this study, the regeneration effect of pressurized water and ultrasonic cleaning was investigated for contaminated filter cloth from the sewage sludge filter press process. For this purpose, contaminated filter cloth was collected from a 3-ton sewage sludge hydrothermal carbon treatment filter press. First, the contamination characteristics were analyzed. According to the location of the filter cloth, air permeability and unit mass were measured, and compared with the values of a new filter cloth. Next, the results were mapped over the entire area to evaluate the contamination characteristics. Finally, pressure cleaning at 3 bar and ultrasound at frequencies of 34, 76, 120, and 168 kHz were performed on the contaminated filter cloth. In addition, the cleaning efficiency was evaluated by 3 levels of contamination degree. As a result, pore contamination occurred mainly at the bottom and both sides of the filter cloth, where the filter material was continuously injected and compressed. Surface contamination appeared evenly over the entire area. As a result of washing, air permeability increased by 1.3-3.1%p and contaminant removal was by 2.7-4.4% under pressure. In ultrasonic cleaning, air permeability increased by 12.5-61.5%p and contaminants were removed by 2.7-29.2%. In ultrasonic cleaning the lower the frequency, the higher air permeability and contaminant removal rate. Also, The higher pore contamination level, the better the air permeability improvement and contaminant removal.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.4
• /
• pp.3-57
• /
• 1985

This research was conducted to examine the feasibility of developing fire retardant particleboard and complyboard. Particleboard were manufactured using meranti particle(Shorea spp.)made with Pallmann chipper, and complyboard meranti particle and apitong veneer (Dipterocarpus spp.). Particles were passed through 4mm (6 mesh) and retained on 1mm (25 mesh). Urea formaldehyde resin was added 10 percent on ovendry weight of particle. Face veneer for complyboard was 0.9, 1.6 and 2.3mm in thickness and spread with 36 g/(30.48 cm)$^2$ glue on one side. Veneers were soaked with 10 percent solution of five fire retardant chemicals (diammonium phosphate, ammonium sulfate, monoammonium phosphate, Pyresote and Minalith), and particles with 5, 10, 15 and 20 percent solution of five chemicals. Particleboard and complyboard were evaluated on physical and mechanical properties, and fire retardancy. The results obtained were summarized as follows. 1. Among five fire retardant chemicals treated to particleboard and complyboard, the retention of ammonium sulfate in 5 percent solution showed the lowest as 1.39 kg/(30.48 cm)$^3$ exceeding the minimum retention of 1.125 kg/(30.48 cm)$^3$ recommended by Forest Products Laboratory and Koch. 2. Particleboard and complyboard treated with diammonium phosphate showed higher modulus of rupture (MOR), modulus of elasticity (MOE), internal bond strength and screw holding power than those with the other chemicals. 3. MOR and MOE of complyboard treated with fire retardant chemicals were greater than those of fire retardant particleboard. 4. Thickness swelling of fire retardant complyboard was lower than that of fire retardant particleboard. 5. The moisture content of the boards treated with Pyresote and Minalith increased and with monoammonium phosphate reduced. 6. Fire retardant particleboard showed no ignition, and fire retardant complyboard started ignition, but time required to ignite was prolonged comparing the controlboard. Complyboard with only shell veneer treated showed ignition and lingering flame, but lingering flame time was shorter than controlboard. Complyboard with treated both core and veneer showed ignition but not lingering flame. 7. Flame length, carbonized area and weight loss were smaller than controlboard but had no significant difference among chemicals treated. 8. Temperature of unexposed surface of fire retardant particleboard was lowered with the increasing concentration of five chemicals. 9. Temperature of unexposed surface of fire retardant particleboard was lowered with the highest in Pyresote and the lowest in Minalith. 10. Temperature of unexposed surface of fire retardant complyboard was lower than that of controlboard.

• Korean Journal of Weed Science
• /
• v.14 no.2
• /
• pp.120-127
• /
• 1994

To establish an efficient herbicide screening method for purple nutsedge(Cyperus rotundus) control, its sprouting characteristics, tuber production and responses on several herbicides were investigated under greenhouse condition. The tubers stored at $4^{\circ}C$ after sterilization with the diluted prochloraz(Spotac) solution showed higher sprouting than the non-sterilized did. The harvested tubers were not dormant, and the sterilized tubers which stored at low temperature had a sprouting capability of about 80% after 6 months. If the fresh weight of purple nutsedge tubers was decreased to below 48%, they could not sprout. However, the tubers soaked in water and then stored at low temperature could sprout by 88% even 6 months later. Sprouting and initial growth of tuber were much better at $35^{\circ}C$-day/$25^{\circ}C$-night than at 30/$20^{\circ}C$ or 25/$15^{\circ}C$. The half-sected tubers, which were prepared by setting the intact tuber of above 1.2g latitudinally, were shown similar initial growth to the intact but those sected crucifically were not. These results suggest that the half-sected tuber itself can be used as a material on herbicide screening. About 1000 tubers could be harvested when 10 tubers planted in a pot($56{\times}35{\times}16cm$) filled with the artificial soil were cultivated in greenhouse of $35^{\circ}C$-day/$25^{\circ}C$-night for 3 months(April-July, 1993). Chlorimuron, Bentazon and Norflurazon were selected as the standards for the screening because of providing relatively effective control on purple nutsedge in both soil-surface and foliar spray treatment.

• Korean Journal of Soil Science and Fertilizer
• /
• v.40 no.1
• /
• pp.85-94
• /
• 2007

To determine the influence of food waste compost (FWC) application on paddy soil, FWC was applied to the paddy soil and then compared with farmer's practice as to the effects on rice and soil environment. Initially, pig manure compost (PMC) had high content of phosphorus ($15g\;kg^{-1}$) and potassium ($23g\;kg^{-1}$), while FWC had high content of total nitrogen ($13g\;kg^{-1}$) and salinity ($18.5g\;kg^{-1}$). Comparison was also made between chemical fertilizer and FWC use as a trial in the paddy field under the clay loam and sandy loam soil. In the panicle formation stage, chemical fertilizer application was proper in clay loam while PMC application was proper in sandy loam. However, chemical fertilizer produced higher yield compared to compost treatment, both on clay loam and sandy loam with 20~25% and 17~19%, respectively. The lower yield in sandy loam maybe due to slow mineralization of compost such that the crop did not effectively use it. Organic matter content in paddy soil after experiment was higher in FWC and PMC plots compared to that in chemical fertilizer plots. But the other soil properties were comparable. Therefore, the FWC compost had little effect on soil when it use as a trial in paddy field. Likewise, after the application of FWC as a trial, analysis of nitrate nitrogen and ammonium nitrogen in the surface water and 60 cm depth of paddy soil water nine days after planting was done. Results revealed that concentration of ammonium nitrogen was similar to irrigation water while nitrate nitrogen concentration was not detected, and hence did not contribute to water pollution. It is concluded that the application of FWC in the paddy field had not affected on environmental pollution in the paddy field. But its use as compost during rice culture reduced yield quantity. Such study should include selection of compost material, amount and method of compost application.

• Korean Journal of Food Science and Technology
• /
• v.53 no.4
• /
• pp.382-390
• /
• 2021

In this study, solubilized yuzu pulp powder (EYP) was produced using enzyme treated yuzu pulp powder (YP) and used to manufacture yuzu granules (0-20% EYP content). The physicochemical, product stability, and functional properties of Yuzu granules were compared among five enzyme treatments. Among the five treatments, CL had the highest YP solubilization yield (48.68%). Microstructural observation of EYP using FE-SEM revealed that its surface became irregular and porous after enzymatic treatment. Compared to YP, EYP had 2 times lower insoluble dietary fibers and 3 times lower hemicellulose and cellulose content. Among the yuzu granules, IV (yuzu granules with 15% EYP) had an excellent water and oil holding capacity and flowability. IV granule had the highest narirutin and hesperidin content of 3.4 mg and 2.2 mg/g DW, respectively and the highest antioxidant (68.4%) and tyrosinase inhibitory activities (82.5%). Therefore, EYP or granule with EYP can be used as a functional component in food industry or pharmaceutical field.

• Radiation Oncology Journal
• /
• v.12 no.3
• /
• pp.271-284
• /
• 1994

Purpose : Phospholipase C(PLC) isozymes play significant roles in transmembrane signal transduction. PLC-${\gamma}1$ acts as the intracellular effector in signal transduction for cellular proliferation and differentiation. Ras oncoprotein is also involved in cell growth. We determined the biological significance of PLC and ras oncoprotein in regeneration following radiation and the effect of different modes of administration of 5-FU. Materials and Methods : To determine the effect of the administration mode of 5-FU on the regeneration of intestinal mucosa of rats following radiation, we compared the expression of PLC and ras oncoprotein in six groups. Group I had no treatment. Group II received radiation(8 Gy) only. Group III received radiation(8 Gy) and 5-FU(150mg/kg) continuous intravenous (iv) infusion for 12 hours. Group IV received radiation(8 Gy) and 5-FU(750mg/kg) iv bolus injection. Group V received only 5-FU(150mg/kg) continuous iv infusion for 12 hours, Group VI received only 5-FU (150mg/kg) iv bolus injection. Through immunoblotting and immunohistochemistry, we examined the expression of PLC and ras oncoprotein in rat jejunum at 96 hours after radiation or 5-FU administration and at 120 hours after radiation and 5-FU adminstration. We also investigated the histological findings using hematoxylin and eosin stain. Results : In the immunohistochemistry study, PLC-${\gamma}1$ expression was the highest in group III followed by groups II and VI in that order and was weakly positive in groups V and VI. PLC-${\gamma}1$ was hardly detected in the control group. The expression of ras oncoprotein was the same as the PLC-${\gamma}1$ expression for all groups. These results were confirmed by the histological findings regarding the mucosal regeneration. In the immunoblotting analysis, PLC-${\gamma}1$ expression was the highest in group III followed by group IV and II in that order. This difference between the immunoblotting and immunohistochemistry study was due to the high expression of PLC-${\gamma}1$ on the damaged surface epithelium rather than to its expression in the regeneration region as observed in the immunohistochemistry study for group IV. The expression of PLC-${\delta}1$ was positive only in group V and VI, which received both radiation and 5-FU, and the expression of PLC-${\beta}1$ was negligible for all groups. Conclusion : These results suggest that PLC-${\gamma}1$ mediated signal transduetion and ras oncoprotein may have a significant role in mucosal regeneration after radiation, and that continuous iv infusion of 5-FU may induce active regeneration in intestinal mucosa following radiation. In addition, the expression of PLC-${\delta}1$ in combined group of radiation and 5-FU implies that PLC-${\delta}1$ may be involved in signal transduction mediated by concerted action between radiation and 5-FU.

• The Korean Journal of Physiology and Pharmacology
• /
• v.22 no.2
• /
• pp.203-213
• /
• 2018

Tumor undergo uncontrolled, excessive proliferation leads to hypoxic microenvironment. To fulfill their demand for nutrient, and oxygen, tumor angiogenesis is required. Endothelial progenitor cells (EPCs) have been known to the main source of angiogenesis because of their potential to differentiation into endothelial cells. Therefore, understanding the mechanism of EPC-mediated angiogenesis in hypoxia is critical for development of cancer therapy. Recently, mitochondrial dynamics has emerged as a critical mechanism for cellular function and differentiation under hypoxic conditions. However, the role of mitochondrial dynamics in hypoxia-induced angiogenesis remains to be elucidated. In this study, we demonstrated that hypoxia-induced mitochondrial fission accelerates EPCs bioactivities. We first investigated the effect of hypoxia on EPC-mediated angiogenesis. Cell migration, invasion, and tube formation was significantly increased under hypoxic conditions; expression of EPC surface markers was unchanged. And mitochondrial fission was induced by hypoxia time-dependent manner. We found that hypoxia-induced mitochondrial fission was triggered by dynamin-related protein Drp1, specifically, phosphorylated DRP1 at Ser637, a suppression marker for mitochondrial fission, was impaired in hypoxia time-dependent manner. To confirm the role of DRP1 in EPC-mediated angiogenesis, we analyzed cell bioactivities using Mdivi-1, a selective DRP1 inhibitor, and DRP1 siRNA. DRP1 silencing or Mdivi-1 treatment dramatically reduced cell migration, invasion, and tube formation in EPCs, but the expression of EPC surface markers was unchanged. In conclusion, we uncovered a novel role of mitochondrial fission in hypoxia-induced angiogenesis. Therefore, we suggest that specific modulation of DRP1-mediated mitochondrial dynamics may be a potential therapeutic strategy in EPC-mediated tumor angiogenesis.