• Journal of Energy Engineering
• /
• v.23 no.4
• /
• pp.56-60
• /
• 2014

Highly concentrated sunlight obtained from a solar concentrator mounted on a solar tracker can be divided into the infrared and visible region before it is actually applied. That is, solar rays are directed toward a unit optically separating sunlight into the infrared and visible region by a hot mirror as they impinge on the surface of a secondary reflector. The Infrared rays can be utilized for thermoacoustic applications while visible rays can be utilized for indoor lighting. This work introduces the separation of two different kinds of light; sunlight and artificial light. As for the artificial light, its wavelength extended from 400m to 720m for the visible region and 620m to 940m for the infrared region. Comparatively, a series of tests performed on sunlight revealed its separation in the visible region from 460m to 680m whereas from 620m to 940m for the artificial light.

• Journal of Bio-Environment Control
• /
• v.14 no.3
• /
• pp.218-231
• /
• 2005

This paper reviews the engineering approach needed to support humans during their long-term missions in space. This approach includes closed plant production systems under microgravity or low pressure, mass recycling, air revitalization, water purification, waste management, elimination of trace contaminants, lighting, and nutrient delivery systems in controlled ecological life support system (CELSS). Requirements of crops f3r space use are high production, edibility, digestibility, many culinary uses, capability of automation, short stems, and high transpiration. Low pressure on Mars is considered to be a major obstacle for the design of greenhouses fer crop production. However interest in Mars inflatable greenhouse applicable to planetary surface has increased. Structure, internal pressure, material, method of lighting, and shielding are principal design parameters for the inflatable greenhouse. The inflatable greenhouse operating at low pressure can reduce the structural mass and atmosphere leakage rate. Plants growing at reduced pressure show an increasing transpiration rates and a high water loss. Vapor pressure increases as moisture is added to the air through transpiration or evaporation from leaks in the hydroponic system. Fluctuations in vapor pressure will significantly influence total pressure in a closed system. Thus hydroponic systems should be as tight as possible to reduce the quantity of water that evaporates from leaks. And the environmental control system to maintain high relative humidity at low pressure should be developed. The essence of technologies associated with CELSS can support human lift even at extremely harsh conditions such as in deserts, polar regions, and under the ocean on Earth as well as in space.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.246-251
• /
• 2016

The use of security lighting that emits spill light is considered a cause of light trespass problems in the residential areas. Therefore, a cutoff panel was installed as an alternative way to reduce light trespass. On the other hand, it has another problem in that it is less effective and is not good enough for aesthetics and safety. In this study, a light cutoff panel was designed and manufactured to reduce the light trespass, and the structure of a proper light cutoff panel was studied. Using a goniophotometer, the light distribution file (IES file) was extracted and the characteristics of light distribution were analyzed using the RELUX program. The results showed that the reduction of spilt light in the backward direction was decreased significantly for all types of light cutoff panels except the coated globe. In the case of a black powder coated light cutoff panel, the forward light caused by light reflected from the surface of the light cutoff panel was also reduced, which means that the black powder coated light cutoff panel is effective in the performance of light cutoff in the forward and backward directions. In addition, the coated glove increased the spilt light in the forward and backward directions because it reflects the upward light to go down. A 90 % accuracy between the measurement value of light trespass and the expected value of the light trespass was obtained from a simulation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.7
• /
• pp.9-15
• /
• 2019

The purpose of present study is to assess the maximum width of the surface cracks using the histogram analysis of image processing techniques in concrete structures. For this purpose, the concrete crack image is acquired by the camera. The image is Grayscale coded and Binary coded. After Binary coded image is Dilate and Erode coded, the image is then recognized as separated objects by applying Labeling techniques. Over time, dust and stains may occur naturally on the surface of concrete. The crack image of concrete may include shadows and reflections by lighting depending on a surrounding conditions. In general, concrete cracks occur in a continuous pattern and noise of image appears in the form of shot noises. Bilateral Blurring and Adaptive Threshold apply to the Grayscale image to eliminate these effects. The remaining noises are removed by the object area ratio to the Labeled area. The maximum numbers of pixels and its positions in the crack objects without noises are calculated in x-direction and y-direction by Histogram analysis. The widths of the crack are estimated by trigonometric ratio at the positions of the pixels maximum numbers for the Labeled objects. Finally, the maximum crack width estimated by the proposed method is compared to the crack width measured with the crack gauge. The proposed method by the present study may increase the reliability for the estimation of maximum crack width using image processing techniques in concrete surface images.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.231-238
• /
• 2011

Variable message signs(VMS) in use are being displaying with the LED device as the luminous source, and it is a recent trend to be changed from the Lamp type to the Surface-Mount Devices(SMD) type. The LED device leads to get VMS display brightly and clearly, leading to have visibility and legibility better than the existing VMS. However, the lights which display off the road, the unnecessary energy, might have negative effect on ecosystem. This study developed the way of getting the lights be displayed only to drivers without the unnecessary energy and estimated the energy efficiency of the development by the optical testing. As a result, this study showed that the energy consumption of the developed display device appeared to decrease by about 36.1% compared to the existing device. Also the upward and downward angle of the lights changed from an angle of $24^{\circ}C$ to $0^{\circ}C$and from an angle of $-24^{\circ}C$ to $-11^{\circ}C$, respectively. Therefore, it anticipates that the developed device would benefit highway safety due to an improvement in visibility and legibility compared to the existing VMS and the energy consumption would be less lower than the existing VMS.

• Journal of the Korean association of regional geographers
• /
• v.13 no.6
• /
• pp.609-622
• /
• 2007

This paper examines the lava tubes designated as a natural monument in Jeju Island, and then makes the several suggestions for conserving and managing them. The cave entrances should be scientifically and strictly managed to prevent the deterioration, and to preserve the interior ecosystem, of the lava tubes. The land use and vegetation of the ground surface over the lava tubes should be also systematically managed; the destroyed sand dunes must be recovered for the development of speleothem in the lava tubes, and the plants with deep roots must be removed for the prevention of ceiling collapse. The provincial authorities should manage the ground surface over the lava tubes as a public land to remove the factors threatening the stability of the lava tubes. Since the roads crossing the ground surface are likely to cause the collapse of the lava tubes, new roads bypassing the caves need to be constructed, and warning signs should be also installed at the traverse points. A monitoring system on the cultural properties protection area over the lava tubes could be effectively established by encouraging residents to participate the conservation program of lava tubes. Since the falling blocks from ceilings have been usually observed in the lava tubes, it is urgent to examine their stability. In particular, the dangerous sections must be continuously monitored for taking a quick measure against the collapse. The air environments of lava tubes need to be scientifically analyzed based upon the long-term observations. The lighting equipments must be improved to minimize the green pollution in the lava tubes open to the public. The numbers of visitors should be also controlled to prevent the destruction and contamination of lava tubes caused by a large number of visitors.

• Journal of Bio-Environment Control
• /
• v.26 no.2
• /
• pp.123-132
• /
• 2017

This study was aimed to investigate the effect of 1)irradiation with several different ratios using red, green, and blue LEDs and 2)various pulsed light irradiation with 50% duty ratio using red and blue LEDs on the growth and morphogenesis of three lettuce cultivars (Lactuca sativar L. cv. 'Jukchukmeon', 'Lolo Rosa', and 'Grand Rapid') in hydroponics culture system for 4 weeks after transplanting. Seeds were sown in rock-wool plug trays and they were placed in a culture room which was controlled at $23{\pm}1^{\circ}C/18{\pm}1^{\circ}C$ temperature and 50-60/70-85% for day and night, respectively, during cultivation period. Irradiated RGB ratios with LEDs were 6:3:1, 5:2.5:2.5, 3:3:4, 2:2:6, and 1:1:8 with $110{\pm}3{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ PPFD on the surface of cultivation bed. The frequencies of pulsed lighting was 50, 100, 500, 1,000, 5,000, 10,000, 25,000Hz (20, 10, 0.1, 0.04 ms) with red and blue LEDs and 50% duty ratio. At the RGB ratio of 6:3:1, the average fresh weight of 'Jukchukmeon' was significantly higher than that of other RGB treatments, but no significant difference compared to the fluorescent treatment. The average fresh weight at 1:1:8 RGB ratio in 'Lolo Rosa' was significantly lower than that of other RGB treatments. Leaf number and fresh weight of 'Grand Rapid' were significantly lower in the control and 1:1:8 RGB treatments, compared to the other RGB treatments. As the ratio of blue light increased, leaf length decreased and leaf shape became round in three lettuces. Although there is little change in growth, it could not be found any tendency to affect the growth and morphogenesis of three lettuces caused by increasing or decreasing frequency of pulsed lighting with 50% duty ratio at the $72{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ PPFD.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.5
• /
• pp.344-349
• /
• 2015

A new information society of late has arrived by the rapid development of various information & communications technologies. Accordingly, mobile devices which are light and thin, easy and convenient to carry on the market. Also, the requirements for the larger television sets such as fast response speed, low-cost electric power, wider visual angle display are sufficiently satisfied. The currently most widely studied display material, the Organic Light-emitting Diodes(OLEDs) overwhelms the Liquid Crystal Display(LCD), the main occupier of the market. This new material features a response speed of more than a thousand times faster, no need of backlight, a low driving voltage, and no limit of view angle. And the OLEDs has high luminance efficiency and excellent durability and environment resistance, quite different from the inorganic LED light source. The OLEDs with simple device structure and easy produce can be manufactured in various shapes such as a point light source, a linear light source, a surface light source. This will surely dominate the market for the next generation lighting and display device. The new display utilizes not the glass substrate but the plastic one, resulting in the thin and flexible substrate that can be curved and flattened out as needed. In this paper, OLEDs device was produced by changing thickness of Teflon-AF of hole injection material layer. And as for the electrical properties, the four layer device of ITO/TPD/$Alq_3$/BCP/LiF/Al and the five layer device of ITO/Teflon AF/TPD/$Alq_3$/BCP/Lif/Al were studied experimentally.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.55-62
• /
• 2005

In this paper, a CAB/CAE integrated optimal design system is developed, in which design and analysis process is automated using CAD/CAE softwares, for a complicated model for which parametric modeling provided by CAD software is not possible. CAD modeling process is automated by using UG/OPEN API function and UG/Knowledge Fusion provided by Unigraphics. The generated model is transferred to the analysis code ANSYS in parasolid format. Visual DOC software is used for optimization. The system is developed for PLS(Plasma Lighting System), which is a next generation illumination system that is used to illuminate stadium or outdoor advertizing panel. The PLS system consists of more then 20 components, which requires a lot of human efforts in modeling and analysis. The analysis for PLS includes static load, wind load and impact load analysis. As a result of analysis, it is found that the most critical component is a tilt assembly, which links lower & upper body assembly. For more reliable analysis, experiment is conducted using MTS and compared with the Finite element analysis result. The objective in the optimization is to minimize the material volume under allowable stresses. The design variables are three parameters in the tilt assembly that are chosen to be the most sensitive in stress values of twelve parameters. Gradient based method and RSM(Response Surface Method) are used for the algorithm and the results are compared. As a result of optimization, the maximum stress is reduced by 57%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.293.1-293.1
• /
• 2016

Various materials including conductive, dielectric, and semi-conductive materials, constitute suitable candidates for printed electronics. Metal nanoparticles (e.g. Ag, Cu, Ni, Au) are typically used in conductive ink. However, easily oxidized metals, such as Cu, must be processed at low temperatures and as such, photonic sintering has gained significant attention as a new low-temperature processing method. This method is based on the principle of selective heating of a strongly absorbent film, without light-source-induced damage to the transparent substrate. However, Cu nanoparticles used in inks are susceptible to the growth of a native copper-oxide layer on their surface. Copper-oxide-nanoparticle ink subjected to a reduction mechanism has therefore been introduced in an attempt to achieve long-term stability and reliability. In this work, a flash-light sintering process was used for the reduction of an inkjet-printed Cu(II)O thin film to a Cu film. Using a photographic lighting instrument, the intensity of the light (or intense pulse light) was controlled by the charged power (Ws). The resulting changes in the structure, as well as the optical and electrical properties of the light-irradiated Cu(II)O films, were investigated. A Cu thin film was obtained from Cu(II)O via photo-thermal reduction at 2500 Ws. More importantly, at one shot of 3000 Ws, a low sheet resistance value ($0.2527{\Omega}/sq.$) and a high resistivity (${\sim}5.05-6.32{\times}10^{-8}{\Omega}m$), which was ~3.0-3.8 times that of bulk Cu was achieved for the ~200-250-nm-thick film.