• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.197-200
• /
• 2006

The bond characteristics of three different types of glass fiber reinforced polymer(GFRP) reinforcing bars with different surface deformations were studied experimentally. Each specimen consisted of a concrete prism, 150 by 150 mm on each edge, with the longer axis in the vertical direction. Two rebars were embedded in each specimen, perpendicular to the longer axis and parallel to and equidistant from the sides of the prism. In vertical direction, one rebar was located at 75 mm from the bottom of the prism, and the other 225 mm from the bottom. All testing procedures including specimens preparation, set-up of test equipments and measuring devices were made according to the recommendations of CSA Standard S806-02.It was found that the bottom reinforcements showed higher bond stress than that of the top rebars.

• 소성∙가공
• /
• 제5권2호
• /
• pp.115-121
• /
• 1996

Recently it is attempted to manufacture gears by various cold forging methods to meet requirements of mass production and uniform qualities. Compared to machined gears cold forged ears reveal higher tooth strength and better surface roughness but they reveal lower geometrical accuracies. Therefore in the present study a series of experiments are performed to investigate relations between geometrical accuracies of dies and billet and those of the final product. The geometrical accuracies of forged gears are considered through functional gear-element tolerances by measuring pitch error profile error lead error radial error tooth thickness and rolling test. Results of the experiments can be summarized as follows: (1) involute spur gears of KS 5(or AGMA7) accuracies can be made,(2) concentricity of die set should be maintained within 0.01mm (3) clearance between the billet and die set should be less than 0.1mm (4) con-centricity and radial runout should be less than 0.08mm and 0.1mm respectively. However it is thought that FEM analysis of elastic/thermal deformations of dies and the billet is necessary for a better understanding of the findings obtained through the present study.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권2호
• /
• pp.162-171
• /
• 2012

A method of hydrodynamic discrete sources is applied for two-dimensional modeling of stepped planing surfaces. The water surface deformations, wetted hull lengths, and pressure distribution are calculated at given hull attitude and Froude number. Pressurized air cavities that improve hydrodynamic performance can also be modeled with the current method. Presented results include validation examples, parametric calculations of a single-step hull, effect of trim tabs, and performance of an infinite series of periodic stepped surfaces. It is shown that transverse steps can lead to higher lift-drag ratio, although at reduced lift capability, in comparison with a stepless hull. Performance of a multi-step configuration is sensitive to the wave pattern between hulls, which depends on Froude number and relative hull spacing.

• 디지털산업정보학회논문지
• /
• 제15권2호
• /
• pp.63-70
• /
• 2019

To increase the efficiency of task on the desk, this paper proposes a reconfigurable desk. The proposed reconfigurable desk is based on the Pin Art technology. For the design of the proposed desk, the upper surface of the desk is divided into small units, and then the user easily controls the height of the divided pieces to make desk a desired shape by using the proposed user interface. The Arduino module controls the hardware and the user interface is configured by using Android applications, making it easy for anyone to use. Through extensive experiments, the proposed system shows that various types of deformations are possible and thus the utilization is very high by mounting diverse devices.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 사면안정학술발표회
• /
• pp.65-81
• /
• 2003

During the last few decades in Korea, the development of hillside or mountain areas has rapidly increased for infrastructure construction such as railroads, highways and housing. Many landslides have occurred during these constructions. Also, the amount and scale of damage caused by landslides have increased every year. In the case of Far East Asia including Korea, the damage of landslides is consequently reported during the wet season. In this paper, the effect of stabilizing piles on slope stability is checked and the behavior of slope soil and piles are observed throughout the year by field measurements in the large-scale cut slopes. In particular a large-scale cut slope situated on the construction site for the express highway in Donghae, Korea. First of all, The behavior of the slope soil was measured by inclinometers during slope modification. Landslides occurred in this area due to the soil cutting for slope modification. The horizontal deformations of slope soil gradually increased and rapidly decreased at depth of sliding surface indicating that the depth of sliding surface below the ground surface can be predicted. On the basis of being able to predict the depth of the sliding surface, stabilizing piles were designed and constructed in this slope. To ensure the stability of the reinforced slope using stabilizing piles, an instrumentation system was installed. The maximum deflection of piles is measured at the pile head and it is noted that the piles deform like deflection on a cantilever beam. The maximum bending stress of piles is measured at the soil layer. The pile above the soil layer is subjected to lateral earth pressure due to driving force of the slope, while pile below soil layer is subjected to subgrade reaction against pile deflection. As a result of research, the effect and applicability of stabilizing piles in large-scale cut slopes could be confirmed sufficiently.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.283-288
• /
• 2004

The measurement of ultra low aspect ratio fluid film thickness is very crucial technique both for the verification of lubrication media characteristics and for the clearance design in many precision components such as MEMS, precision bearings and other slideways. Many technologies are applied to the measurement of ultra low aspect ratio fluid film thickness (i.e. elastohydrodynamic lubrication film thickness). In particular, in-situ optical interferometric method has many advantages in making the actual contact behaviors realized with the experimental apparatus. This measurement method also does the monitoring of the surface defects and fractures happening during the contact behavior, which are delicately influenced by the surface conditions such as load, velocity, lubricant media as well as surface roughness. Careful selection of incident lights greatly enhances the fringe resolutions up to $\~1.0$ nanometer scale with digital image processing technology. In this work, it is found that coaxial aligning trichromatic incident light filtering system developed by the author can provide much finer resolution of ultra low aspect ratio fluid film thickness than monochromatic or dichromatic incident lights, because it has much more spectrums of color components to be discriminated according the variations of film thickness. For the measured interferometric images of ultra low aspect ratio fluid film thickness it is shown how the film thickness is finely digitalized and measured in nanometer scale with digital image processing technology and space layer method. The developed measurement system can make it possible to visualize the contact deformations and possible fractures of contacting surface under the repeated loading condition.

• 한국전산구조공학회논문집
• /
• 제24권4호
• /
• pp.439-447
• /
• 2011

강바닥판 교량의 교면포장은 차량의 윤하중을 상판에 고르게 분포시켜 교량 상판을 보호하는 역할을 한다. 하지만 교량의 장대화가 가속화됨에 따라 포장체와 강바닥판의 두께가 얇아지고 이 때문에 교면포장의 횡방향 균열이 빈번하게 발생한다. 본 연구에서는 강바닥판 교면포장의 파손원인 규명과 저감 방안을 모색하기 위해 윤하중을 받는 강박스형 거더를 가진 강바닥판의 유한요소해석을 수행하였다. 다양한 구조적 매개변수 변화에 따른 교면포장 상면 변형도를 조사한 결과 해석결과에서 공통적으로 웹 상단에서 큰 인장변형이 발생하였고, 이것이 교면포장의 구조적인 파손의 주요 원인이 되는 것을 알 수 있다.

• 대한금속재료학회지
• /
• 제47권7호
• /
• pp.416-422
• /
• 2009

Approaches for analyzing indentation hardness are still controversial, although the instrumented indentation technique has been generalized as one powerful method that can record surface deformation behaviors. Material pile-ups around the indenter/surface contact region make the conventional Oliver and Pharr's analysis on the instrumented indentation curve inaccurate. Thus, in order to prove the validity of the hardness analyses, five approaches were applied to the experimental data obtained from fused quartz and (100) monocrystalline tungsten specimens; an elastic recovery analysis on instrumented indentation curves, three indentation work analyses on the unit plastic volume, and a differentiation analysis on remnant indentation morphologies were tried. Five kinds of indentation hardness overlapped on one result plot showed the validity of each analysis. The modified indentation work approach based on a new definition of plastic volume showed consistent results with those from the Oliver-Pharr's and image differentiation methods. In the case of pile-up accompanying deformation, the Oliver-Pharr's and image differentiation methods showed the upper and lower limits of indentation hardness, respectively.

• 콘크리트학회논문집
• /
• 제18권3호
• /
• pp.303-312
• /
• 2006

본 연구에서는 GFRP 보강근의 인장특성치 시험을 위한 그립 시스템의 적합성을 검증하기 위하여 캐나다 규준에서 제안하는 그립(CSA 그립), ASTM에서 제안하는 그립(ASTM 그립) 및 프리스트레싱 강연선의 정착에 일반적으로 사용되는 쐐기형 그립 등을 사용하여 GFRP 보강근에 대한 인장특성치 시험을 실시하였다. 또한, 현재 외국에서 상용화되고 있는 대표적인 2종류의 GFRP 보강근(나선형 GFRP 보강근, 모래분사형 GFRP 보강근) 및 국내에서 자체 제작한 원형 GFRP 보강근을 대상으로 하여 인장특성치 분석을 위한 시험을 실시하고 각각의 제안된 그립의 적용성 여부를 검토하였다. 본 시험에 사용된 시험편의 제작, 가력 및 측정장치의 설치 등은 CSA S806-02에서 제안하는 권고사항에 따라 실시하였다. 외국의 상용화된 GFRP 보강근에 대하여 그립의 종류를 달리하여 실시된 본 시험결과에 의하면, CSA 그립을 사용하여 시험된 GFRP 보강근의 인장강도가 가장 높은 값을 보이는 것으로 나타났다. 그러나 ASTM 그립을 사용한 시험편에서 관측되는 강도저하 현상은 CSA 그립을 사용한 시험체에 비하여 약 10% 미만인 것으로 관측되었다. 한편, CSA 그립은 제작공정이 까다로울 뿐만 아니라 재사용이 불가능하여 경제성 측면에서도 불리한 것으로 파악되었다. 따라서, 실용적인 측면에서 판단하면 GFRF 보강근의 인장시험에는 ASTM 그립이 적절할 것으로 판단된다.

• 한국지반환경공학회 논문집
• /
• 제4권3호
• /
• pp.27-40
• /
• 2003

본 연구에서는 프리텐션을 적용한 쏘일네일링 공법을 제시하고, 프리텐션 쏘일네일링 시스템에 대한 변위제어방식 현장인발시험을 총 9회 실시하여 프리텐션 쏘일네일링 구조체의 관련 설계변수인 쉬스관 길이 및 고정콘 유 무 등에 대한 영향에 대해 분석하였으며, 아울러 프리텐션 하중의 평가도 다루어 졌다. 또한 응력제어방식 현장인발시험을 총 3회 실시하여, 일반 쏘일네일 및 프리텐션 쏘일네일의 장 단기적인 인발-변형 특성 등을 비교 분석하였다. 계속해서, 프리텐션 쏘일네일링 시스템의 안정성 평가를 위해, 예상파괴면 및 최소안전율을 결정하기 위해 사면안정해석 등에 주로 적용되고 있는 전단강도감소기법을 이용한 수치해석적 접근방법의 제시 및 분석 등이 이루어졌다.