• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.434-443
• /
• 2023

We have investigated the performance improvement of grease by synthesizing calcium sulfonate grease as an alternative to lithium grease, which is widely used globally. Since the composition ratio of the grease, when manufactured, is usually 50% base oil and 50% thickener, using grease as a lubricant in a cryogenic environment is not encouraged due to its inferior low-temperature performance. In this study, we have synthesized three types of calcium sulfonate grease with paraffin oil and PAO-based base oil and thickener. Furthermore, lithium grease was synthesized via saponification with PAO-based base oil, lithium hydroxide, 12-hydroxystearic acid, and sebacic acid. We have measured low-temperature characteristics using a rheometer and low-temperature torque meter, and tribology characteristics were obtained using a four-ball lubricant tester and schwingung reibung verschleiß (SRV). As a result, the flow point of the calcium sulfonate grease synthesized with a PAO-based base oil and thickener was found to be -40℃, overcoming the existing calcium sulfonate grease's low-temperature limitation. Moreover, the synthesized calcium sulfonate grease showed low-temperature performance similar to that of lithium grease synthesized with PAO base oil, but superior anti-wear, extreme pressure, coefficient of friction, heat resistance, adhesion, and corrosion resistance. It is thus expected to commercially replace the existing lithium grease.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.664-672
• /
• 2011

A series of hydrophilic chromophores was synthesized through introduction of dendritic sulfonate anions using click chemistry. A dendron structure bearing several sulfonate groups enhances hydrophilicity of attached chromophores. A click triazole formation connects chromophores with hydrophilic groups. A neutral trichloroethyl sulfonate has versatile features such as easy introduction, chemical endurance for isolation or storage, and convenient transformation to a hydrophilic anion. Zinc and OH mediated cleavage of trichloroethyl group from the neutral sulfonate undergoes to generate a water-soluble sulfonate anion. The solubility was examined with different counter cations and in different pH media and thus increased with the number of attached sulfonate ion. Two hydrophilic chromophores of stilbene-derived and azobenzene-derived dipolar structures exhibit clear negative and positive solvatochromism in protic solvents, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.36-41
• /
• 1998

Intercalation compounds of alkyl sulfonates into layered double hydroxides (LDH) have been directly synthesized. From the X-ray diffraction data and the alkyl sulfonates size, the orientation of the intercalated alkyl sulfonate into the layered double hydroxide was determined. The intercalated alkyl sulfonate is arranged with molecular chain perpendicular to the hydroxide layer with an antiparallel pattern.

• Journal of Pharmaceutical Investigation
• /
• v.2 no.1
• /
• pp.14-17
• /
• 1972

Spectrophotometric determination of isonicotinic acid hydrazide sodium methane sulfonate was examined and a new method has been established. Isonicotinic acid hydrazide sodium methane sulfonate reacts with acetylacetone solution (NASH Reagent) to produce a yellow dye, which exhibits absorption maximum at about $412\;m{\mu}$. Limits of masurement of isonicotinic acid hydrazide sodium methane sulfonate was $20-100{\mu}g/ml$. By this method isonicotinic acid hydrazide methane sulfonate can be determined in the presence of isonicotinic acid hydrazide.

• Membrane Journal
• /
• v.6 no.4
• /
• pp.273-283
• /
• 1996

A cation-exchange membranes were prepared by polystyrene and poly(sodium 4-styrene sulfonate). The degree of crosslinking of polystyrene membranes was controlled by DVB. At the same time, the structure of PS membranes was changed from RO to MF by varying the concentration of PSS in the casting solution. Water flux increased with PS-PSS membranes due to the sulfonate groups, and final membrane cast from the solution containing 5% of DVB and 3% of PSS showed MF structure.

• Journal of the Korean Chemical Society
• /
• v.7 no.1
• /
• pp.25-28
• /
• 1963

Sodium alizarin sulfonate forms stable complex with uranyl ion, particularly over pH 3.85 condition. Spectrophotometric measurements have been used to study these complex. The continuous variation method and mole ratio method have been used to establish that the most stable complex contains one uranyl ion per sodium alizarin sulfonate.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.5
• /
• pp.510-516
• /
• 2016

This study examines the effects of linear alkylbenzene sulfonate on hydrogen fermentation of food waste. The hydrogen production rate was similar with different linear alkylbenzen sulfonate (LAS) concentrations. The maximum hydrogen yield increased with increasing LAS concentration. The highest maximum hydrogen yield was $0.550{\pm}0.005mol$ H2/mol hexose at LAS for 5.52 mg/L. But the maximum hydrogen yield decreased above LAS for 11.05 mg/L. The concentration of acetate in control reactor was increased, but it decreased with increasing LAS concentration in other reactors.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.8-15
• /
• 2019

In this study, we synthesized a calcium sulfonate complex grease and a lithium complex grease to investigate their physical, rheological and tribological properties. The thermal stability of the calcium sulfonate was higher than $300^{\circ}C$ and the lithium complex grease was $245^{\circ}C$ in the dropping point test. In the grease viscosity measurement, the calcium sulfonate complex grease was measured as $7.0Pa{\cdot}s$ and the lithium complex grease was as $4.5Pa{\cdot}s$. Therefore, it was confirmed that the calcium sulfonate complex grease is superior to the lithium complex grease in terms of thermal stability and cohesiveness. In the 4-ball wear test, the calcium sulfonate complex grease was measured to be 0.43 mm and the lithium complex grease to 0.85 mm. In the 4-ball extreme pressure test, calcium sulfonate complex grease was measured as 620 kgf and the lithium complex grease was as 125 kgf. Therefore, it was confirmed that the calcium sulfonate complex grease is superior to the lithium complex grease in abrasion resistance and load-bearing property. It was found that the calcium sulfonate complex grease is more effective than the lithium complex grease in the lubrication at high temperature and high load.

• Korean Chemical Engineering Research
• /
• v.48 no.4
• /
• pp.444-449
• /
• 2010

In this study, the petroleum sulfonate(PS) was synthesized from pyolyzed fuel oil by sulfonation reaction with sulfuric acid. The PS synthesized had surfactant behaviors relating to the interfacial properties such as surface tension, surface adsorption, and wetting, etc. These interfacial properties were affected by the sulfonation ratio in the synthesis. As the sulfonation ratio increased, the surface tension of the PS aqueous solution decreased. However, when the ratio was too high, the surface tension was increased due to the extremely higher value of hydrophilicity of PS. At the optimum sulfonation ratio, the PS had a good wettability on the cement particles and a good fluidity of the cement mortar with a high adsorption.

• Polymer(Korea)
• /
• v.26 no.4
• /
• pp.516-522
• /
• 2002

The ion exchange characteristic of quaternary ammonium as functional group containing aminated acrylic fibrous ion exchanger were studied for the adsorption of linear alkylbenzene sulfonate (LAS) in a continuous ion exchange process. The adsorption capacities of aminated acrylic for LAS as the adsorption temperature were increased with increasing adsorption temperature and were equilibrated at $40^{\circ}C$. The maximum adsorption capacities as column packing ratio (L/D) were obtained at L/D>2. The adsorption capacity for LAS was increased with increasing pH and the maximum adsorption capacity as pH was obtained at pH 7. The effects of temperature and pH were similar to those of flow rate and concentration of LAS tin the breakthrough curves, the breakthrough time and slope of breakthrough corves decreased with increasing flow rate and concentration of LAS in adsorption process.